A Safe Fleet Brand Instruction Manual G-SERIES Backup Camera System with Auto Dimming, Compass and Temperature RVS-776718-DCT Reverse With Confidence ™ Rear View Safety, Inc.
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 08-09 Adjustable Grid Line. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation and Wire. . . . . . . . . . . . . . . . . . . . . . . . . 11-13 Digital Compass Calibration. .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified. Failure damage.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
Replacement Monitor The mirror monitor replaces the existing car mirror. Carefully remove the mirror off the “pin”. Slide the replacement mirror on to the pin and secure it with the screw provided (already in the screw hole).Different cars have different brackets, depending on your vehicle make and manufacturer. There are many methods to remove the original rearview mirror, however, please don’t force the mirror off the bracket.
INSTALLATION GUIDE + TIPS Wiring After connecting the camera to the “camera cable” the camera should be plugged into AV2 input. Connect the RED 12V power wire to an ignition power source and the BLACK 12V ground wire to a chassis ground. The GREEN wire is the REVERSE trigger wire. Connect this wire to the vehicle’s backup light circuit to activate the rear-view image whenever the vehicle shifts into reverse. To connect a second camera, connect it to AV1 input.
ADJUSTABLE GRID LINE Grid Lines Generally, to help drivers estimate the distance from obstacles, there are three lines for reference- red, yellow, and green. Those three lines are displayed on the monitor when car is reversing. The green line is 3M from the back of the car and the yellow line is 6.5 ft. The distant red line is 1M from the backside of car while the close red line is 0.4M. Both reference lines on the left and right should leave 0.2M space from the car.
FIGURE 1.1 INSTALLATION AND WIRE FIGURE 1.
HOW TO WIRE + SPLICING FIGURE 2.1 1. RED- Power (+) 2. YELLOW- Video 3. GREEN- Mirror / Normal Imaging 4. WHITE- Audio 5.
FIGURE 2.
Digital Compass Calibration DIGITAL COMPASS CALIBRATION The compass can be calibrated by driving your vehicle in several complete circles. See figures below. If the vehicle’s compass headings become inaccurate, the compass can also be manually calibrated: 1.Press the “MENU” three times to enter into the “SETTING” menu, and press “SEL/REC” to choose “ANGLE”. Scroll UP/DOWN to adjust the angle. Please visit: http://magnetic-declination.com/ to find out the compass angle of your area. (5-1) 2.
Caution 1. Make sure the rear view mirror is clearly visable to the driver before calibration. 2. Do not calibrate the compass near a large truck. 3. Make sure that you drive in several complete circles, the steering wheel needs to reach a certain angle for calibration to function properly. The diameter of the driving circle should be close to 5 meters. 4. Do not drive too fast when calibrating, your pace should be equal to one third normal adult walking speed.
Q&A TEMPERATURE SETTING Q: Why does the compass need to be calibrated? A: The magnetism of a car is stronger than the magnetism of the Earth. The compass will only function properly if it is calibrated to the magnetic conditions of Earth. Q: Why is the compass not accurate in some areas? A: In some areas, such as iron mines, high-intensity magnetic fields change the Earth’s magnetism. Q: Why are old cars more difficult to calibrate than new cars? A: The older a car is, the more magnetized it will be.
Temperature Sensor Installation Locate the temperature sensor between the front of the radiator and the front bumper. Slide the metal clip over the edge of the sheet metal or plasic shield until it is secure. Do not install the temperature sensor near the engine. We do not recommend using the compass in an area with high magnetic lines of flux. For example, in the north of Canada.
Rear View Safety MAGNETIC FLUXLINE DISTRIBUTION
MAGNETIC FLUXLINE DISTRIBUTION 19 Reverse With Confidence ™
About Our Monitor 10.25” MONITOR SPECIFICATIONS 3” SPECIFICATIONS: 20 Screen Size: Display Screen: Display Resolution: Aspect Ratio: Color Depth: Pixel Pitch (mm) Power Consumption: Working Voltage: 4.3” TFT-LCD 400(H)x234(V) 16:9 16.7M dithering 0.219x0.
About Camera Reverse With Confidence ™ CAMERA SPECIFICATIONS SPECIFICATIONS: 21
CAMERA INSTALLATION Camera Installation Mounting Position view angle installation 22 position Rear View Safety 170º
No Image On Screen • Do a hard reset, unplug all cables and power cables, leave out for 1 minute and then re-connect them • Check to ensure that the connection to the camera is tight • Verify camera cable is plugged into port labeled Backup Camera • Verify cable is connected to monitor • Verify camera is connected to cable • Connect known working camera and cable to monitor • Verify Green trigger is receiving power Reverse With Confidence ™ TROUBLESHOOTING • Verify that the green positive trigger on pow
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER Reverse With Confidence ™ DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
A Safe Fleet Brand If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.