Instruction Manual Backup Camera System with Waterproof Quad View Monitor and Heated Camera RVS-8129900Q Reverse With Confidence ™ Rear View Safety, Inc.
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . 08-09 Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Remote. . . . . . . . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects, helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified. Failure damage.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
INSTALLATION GUIDE Wiring After connecting the monitor to the power harness, plug the camera into the CAM 3 input. Connect the RED 12V power wire to an ignition power source and the BLACK 12V ground wire to a chassis ground. The BROWN wire is the REVERSE trigger wire. Connect this wire to the vehicle’s backup light circuit to activate the rear view image whenever the vehicle shifts into reverse. To attach a second camera, connect it to the CAM 1 input.
Precautions For Use Of Monitor I. The monitor is made of glass and plastic. Do not subject it to a mechanical shock by dropping it from a high place, etc. II. Do not apply excessive force to the monitor surface or the adjoining areas since this may cause the color tone to vary. III. Only clean with a soft dry cloth and/or Windex. IV. Do not attempt to disassemble the mirror monitor.
MONITOR Components 10 Rear View Safety Waterproof Camera
7” Waterproof Quad View Monitor with a TFT LCD digital color touch screen display. Monitor comes with a U-Bracket, swivel head mount, and a waterproof rating of IP69K.
MONITOR Monitor Dimensions 12 Dimension 7” TV System NTSC/ PAL Resolution 800 x 3 (RGB) x 480 Brightness 400 cd/m² Contrast 500 :1 Viewing Angle U: 50°/ D: 60°, R/L: 70° Aspect Ratio 16:9 Operating Temperature -10 ~ +65ºC Storage Temperature -30 ~ +80ºC Power Consumption Max. 25W Power for Cameras Max. 4×300mA, 12V Dot Pitch 0.192 (H) x 0.
MONITOR Reverse With Confidence ™ 13
MONITOR 1. Remote control signal sensor 2. Power button 3. Increase / decrease volume and switch sub-menu values 4. Menu selection and toggle display mode (SINGLE/DUAL/TRIPLE/ QUAD/PIP IMAGE) 5. Menu button 6.
Connections CONNECTIONS Reverse With Confidence ™ 15
REMOTE Remote Operations 1. MUTE: MUTE / UNMUTE volume 2. POWER: Turn monitor ON / OFF 3. MENU: Toggle between menus 4.
5. DN: Toggle selection DOWN & toggle display mode (SINGLE/ DUAL/TRIPLE/QUAD/PIP IMAGE) 6. VOL: Decrease volume & toggle sub-menu values 7. VOL: Increase volume & toggle sub-menu values 8. MODE: Toggle display mode (SINGLE/DUAL/TRIPLE/QUAD/PIP IMAGE) 9. SEL.: Toggle jump key 10. P/N: Toggle between PAL/NTSC 11. LANG: Toggle language 12. REST: Restore factory settings 13.
On-Screen Display (OSD) OSD SETUP • SCALE: Toggle distance grid lines ON/OFF. When ON, distance grid lines will be displayed when backup camera (CAM 3) is triggered. • INPUT SCAN: Toggle camera input auto identification. When ON, monitor will display connected cameras and skip inputs not connected. • BOUNDARY: Toggle border color between camera inputs (WHITE/GRAY/ BLACK/UNCOLORED). • LANGUAGE: Toggle OSD language (ENGLISH/FRENCH/DUTCH/SPANISH/GERMAN). • Software version appears under LANGUAGE.
Trigger Setting • TURN IMAGE: Display options when side cameras (CAM 1, CAM 2) are triggered. When on SINGLE, the corresponding camera will display when either camera is triggered. When on SPLIT, a split image of side and rear view camera will be displayed when either side camera is triggered. • REAR IMAGE: Display options when backup camera is triggered. When on BACK, just the backup camera will display when triggered. When set as TRIPLE, the left, right, and backup camera will simultaneously display.
Jump Key Setting JUMP KEY MENU AND TOUCH-SCREEN OPERATIONS 20 Rear View Safety
• REC-V OUT: Toggle which camera view will record when a DVR is attached (LEFT/RIGHT/FRONT/QUAD). • AUTOSCAN: When setting is ON, the monitor automatically switches between connected camera inputs and quad view. • SCAN DELAY: Toggle AUTOSCAN delay (0-60 seconds). • JUMP KEY: Toggle jump key destination. Select from 13 display modes as shown on the left. • POWER ON: Toggle default display mode. Select from 13 display modes as shown on the left. • BEEP: Control audible alert (beep) when buttons are pressed.
TOUCH SCREEN OPERATIONS When in quad view, press any channel to view full screen 22 Rear View Safety
Touch screen menu TOUCH SCREEN OPERATIONS Reverse With Confidence ™ 23
TOUCH SCREEN OPERATIONS Exchange picture locations of any two cameras displayed in multi-viewing mode 24 Rear View Safety
Swap display position (dual/ triple view) TOUCH SCREEN OPERATIONS Reverse With Confidence ™ 25
Switch to next display mode TOUCH SCREEN OPERATIONS Switch to previous display mode 26 Rear View Safety
Camera Dimensions CAMERA DIMENSIONS Reverse With Confidence ™ 27
Camera Specifications CAMERA SPECIFICATIONS Image Device TV System Total Number Of Pixels Effective Pixels Sensing Area Sync. System Resolution Minimum Illumination Microphone Video Output Gamma Correction AGC S/N Ratio White Balance Electronic Shutter BLC Current Consumption Power Supply Anti-vibration Operating Temperature Storage Temperature Lens Lens Angle 28 1/3” SONY® Super HAD CCD PAL/NTSC PAL: 537 (H) x 597 (V) / NTSC: 537 (H) x 505 (V) PAL: 500 (H) x 582 (V) / NTSC: 510 (H) x 492 (V) 4.
Troubleshooting Problem Possible Causes/Solutions No picture/sound No picture No sound Dark picture No color Upside down/inverted picture Backup camera does not display when car is in reverse Adaptor is connected incorrectly. Improper power supply. Unit is off. Check cable connection. Audio cable improperly connected. Volume is off or set very low. Adjust brightness/contrast. Low environmental temperature. Adjust the color settings. Use horizontal/vertical selection switch on remote control.
ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER Reverse With Confidence ™ DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
