Instruction Manual Backup Camera System With Dual Lens Camera RVS-813613-NM Reverse With Confidence ™ 1
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04-06 Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . 07 Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08-09 Adjustable Grid Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installation and Wire. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified. Failure damage.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot/moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
Cable 1. Be sure to position the cable properly. The camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts. 2. Fasten all cables and secure all excess cable. INSTALLATION GUIDE Monitor 1. To Attach the Pedestal mount to the dashboard or to the head-liner use self-tapping screws and/or the adhesive pad. 2.
Wiring Reverse With Confidence ™ INSTALLATION GUIDE To power the system connect the power (RED) 12V+ wire to ignition power and the ground (BLACK) wire to chassis ground. • These are the only wires needed to power the entire system and all the cameras. Each camera can be seen at any time by simply pressing the power button and using the V1/2 button to toggle.
INSTALLATION AND WIRE • Audio: There is audio on channels 2 and 3. On channel 3 the blue trigger wire must be energized (12V) to activate the audio. On channel 2 the audio is always on. • Grid-lines: The grid-lines are also carried through the blue wire. To use the grid-lines for reversing, connect the blue wire to a reverse power. • There is a built-in voltage regulator for our systems which can handle 12-24 volts. Real consumption is 10 to 30 Volts. 1. 2. 3. 4. 5.
Monitor INSTALLATION AND WIRE 1 2 3 4 3 Amp Fuse 1. DC12V-24V (red) 2. Ground (black) 3. Port #3 (blue) 4. Port #2 (white) 5.
Camera selection Toggle selection down Menu Toggle selection up MONITOR OPERATION Power Rotate Image • "Brightness" "Contrast "Saturation" "Sharpness": adjust image properties • Picture Adjust: Stretch image horizontally (right/left and left/right) • Turn: Toggle between mirror/normal image on each individual channel • Day/Night: Toggle between back-lit buttons and auto dimming • Name: Change name of each individual channel • Trigger Source: Toggle channel destination for each trigger • Trigger Delay
Reverse With Confidence ™ CAMERA FEATURES Dual Camera - Perfect for Viewing Traffic and Vehicle Bumper 130° Ultra-Wide all Encompassing View 18 Infra-Red Lights - 9 on Each Camera Completely Waterproof - IP68 Rating Built-in High Gain Mic 13
Monitor Information MONITOR SPECIFICATIONS Type Screen Size Dot Resolution Display Format/Contrast Display Brightness Video Input Video Source Power Supply Power Consumption Audio Output Operating Temperature Storage Temperature Video System Overall Dimensions Weight Vibration Rating DOT PITCH Active Area Sync System 14 LED Digital Panel 7" 800 X 3 (RGB) X 480 16:09 / 500:01:00 400cd/m2 3 channel CVBS 1Vp-p, 750 DC 9V - 32V 5W 0.5W speaker -20°C ~ +70° C -30°C ~ +85°C Auto NTSC/PAL 7" (L) x 5.
Camera Information 1/3" Sony® CCD 250,000 pixels r=0.45 to 1.0 480 TV Lines PAL: 500 (H) X 582 (V), NTSC: 510 (H) X 492 (V) View Angle 130° Lens 2.1mm Sync System Internal Synchronization Infra-red distance 50 Feet (18 Infrared) Usable Illumination 0 Lux (IR On) Power Source DC 9v-32V S/N Ratio More than 48dB Electronic Iris 1/50, 160-1/100,000sec Video Output 1Vp-p 75 Ω IR Switch Control ACDS Automatic Control Vibration Rating 5.
WARRANTY ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER Reverse With Confidence ™ DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
