Table of Contents Introduction ..................................................................................................3 Safety Information .................................................................................4-6 Before Beginning Installation...................................................................7 Installation Guide.....................................................................................8-9 Installing the Monitor..............................................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before Beginning Installation Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations.
Installation Guide Cable 1. Be sure to position the cable properly. The camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts. 2. Fasten all cables and secure all excess cable. Monitor 1. To Attach the Pedestal mount to the dashboard or to the headliner use self-tapping screws and/or the adhesive pad. 2.
• To power the system connect the power (RED) 12V+ wire to ignition power and the ground (BLACK) wire to chassis ground. • These are the only wires needed to power the entire system and all the cameras. Each camera can be seen at any time by simply pressing the power button and using the V1/2 button to toggle. • The trigger wire represents channel 2 and will turn on when the trigger wire is energized with 12V.
Installing the Monitor MONITOR 2*3pcs fuse POWER POWER GND BACK 5 video 1 video 2 yellow connects to video 2 audio 1 3*4pcs audio 2 red connects to audio 2 CAMERA 10 REAR VIEW SAFETY
Monitor Operation “-” DOWN CAMERA SELECTION MENU/ SELECTION BUTTON “+” UP ROTATE IMAGE POWER ON / OFF (Back/Exit when in Menu Mode) !! # " !!$ % )* $ %!!& )* + )* • Name: the name of each individual channel. Change !! " !! " • Trigger Change the channel destination source: !! # !! # for each trigger.
Splitting & Splicing 2 x 3pcs fuse net red black blue yellow green white orange RED - POWER BLACK - GND BLUE - BACK 5 video 1 video 2 audio 1 3*4pcs 12 audio 2 REAR VIEW SAFETY
Monitor Specifications TFT LCD Digital Monitor Screen Size 9” Dot Resolution 800H x 3 (RGB) x 480V Display Brightness 400cd/m2 Video Input 2 Channel Display Format Viewing Angle Video Source Power Supply Power Consumption 16:9 / 500:1 U:50° / D:60° / R:70° 1Vp-p, 75 DC 12V-24V (+/- 10%) 5W Operating Temperature -30°C ~ +80° C Overall Dimensions 9”L x 6”H x 1”D Video System Auto NTSC/PAL Weight 400G Dot Pitch 0.192H x 0.
Monitor Dimensions 9” Menu/ Selection Button Camera Selection 6” Rotation Imager (Exit in Menu Mode) Down Up Power On/Off power video select down/up menu mirror/ normal image 14 REAR VIEW SAFETY
Troubleshooting Monitor Displays Blue Screen & Displays No Signal • Verify that the blue trigger is • Do a hard reset, unplug all connected to 12v+. cables, leave out for 1 minute and then re-connect them. If the problem still persists, ver• Check to ensure that the connection to the camera is tight. ify that alternate ports work. If • Verify camera cable is plugged alternate ports do not work, remove Blue Trigger wire from into port labeled Backup 12V+ and select alternate chanCamera nels.
Warranty One Year Warranty Rear View Safety, Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.