Table of Contents Introduction ...................................................................................................3 Safety Information ..................................................................................4-6 Before Beginning Installation...................................................................7 Installation Guide.........................................................................................8 Wiring Camera & Monitor.........................................
Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already ex- ists in your vehicle.
Safety Information Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. USAGE • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION • Electric shock or product malfunction may occur if this product is installed incorrectly. • Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction. • Take special care when cleaning the monitor. • Make sure to firmly affix the product before use. • If smoke or a burning smell is detected, disconnect the system immediately.
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before You Begin Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations.
Installation Guide Cable 1. Be sure to position the cable properly. The aviation camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather elements. Do not run the cable over sharp edges, do not kink the cable and keep away from HOT and rotating parts. 2. Fasten all cables and secure all excess cable. Replacement Monitor 1. The Mirror Monitor replaces the existing rear view mirror in vehicle. 2.
Wiring Camera & Monitor • To power the system connect the power (RED) 12V+ wire to ignition power and the ground (BLACK) wire to chassis ground. • These are the only wires needed to power the entire system and all the cameras. Each camera can be seen at any time by simply pressing the power button and using the V1/2 button to toggle. • The three positive trigger wires (BLUE-CH1, WHITE-CH2, YELLOW-CH3) each represent one channel and will turn on their channel when the trigger wire is energized with 12V.
Wiring Camera & Monitor • Audio: There is audio on channels 2 and 3. On channel 3 the blue trigger wire must be energized (12V) to activate the audio. On channel 2 the audio is always on. • Grid-lines: The grid-lines are also carried through the blue wire. To use the grid-lines for reversing, connect the blue wire to a reverse power. • There is a built-in voltage regulator for our systems which can handle 12-24 volts. Real consumption is 10 to 30 Volts.
Replacement Installation Diagram Replacement Monitor Figure 1.1 Figure 1.2 Figure 1.
Clip-On Installation Diagram Clip-On Monitor Figure 1.1 Figure 1.2 Figure 1.
Installing the Monitor 33ft Extension Cable Monitor Power Harness 3 Amp Fuse 1 2 3 4 5 Optional Camera Available 1. DC12V-24V 2. Ground 3. Port #3 (blue) 4. Port #2 (brown) 5.
Monitor Operation UP MENU DOWN V1/V2 ON/OFF • • • • • • • • • Brightness, Contrast, Saturation, Sharpness: Adjust image properties Picture Adjust: Stretch image horizontally (right/left and left/right) Turn: Toggle between mirror/normal image on each individual channel Name: Change name of teach individual channel Trigger Delay: Adjust time delay on each trigger Trigger Source: Toggle channel destination for each trigger Distance Grid: Toggle which channel distance grid lines will display on Grid Position
Splicing 1. 2. 3. 4. 5. 1. Red - Power (+) 2. Yellow - Video 3. Green - Mirror / Normal Imaging 4. White - Audio 5.
Positioning General Installation Location 16 REAR VIEW SAFETY
Monitor Dimensions Replacement Monitor 17 Clip-On Monitor REAR VIEW SAFETY
Monitor Specifications TFT LCD Digital Monitor Screen Size Digital 7” Display Format 16:9 Dot Resolution Display Brightness 800H x 3 (RGB) x 480V 400cd/m2 Viewing Angle 90° min Video Source 1Vp-p, 75Ω Video Input Power Supply 3 channel DC 12V-24V (+/-10%) Power Consumption 5W Video System Auto NTSC/PAL Weight 400G Dot Pitch 0.192H x 0.1805V Operating Temperature Overall Dimensions Impact Rating Sync System Reverse With Confidence™ -10°C - +65° C 9”L x 4.
Troubleshooting Monitor Displays Blue Screen & Displays No Signal • Do a hard reset, leave out for 1 minute and then re-connect them. • Check to ensure that the connection to the camera is tight. • Verify camera cable is plugged into port labeled Backup Camera • Verify that the blue positive trigger on power harness is put to power 12v+. If the problem still persists, verify that alternate ports work. If alternate ports do not work, remove Blue Trigger wire from 12V+ and select alternate channels.
Warranty One Year Warranty Rear View Safety Inc. warrants this product against material defects for a period of one year from date of purchase. We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mis-handling of the electronic components. Rear View Safety Inc. is not responsible for consequential damages of any kind.
Disclaimer Rear View Safety and/or its affiliates does not guarantee or promise that the user of our systems will not be in/part of an accident or otherwise not collide with an object and/or person. Our systems are not a substitute for careful and cautious driving or for the consistent adherence to all applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or for any other motor vehicle equipment mandated by law.
Take Notes Reverse With Confidence™ 22
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
