Instruction Manual 9" TFT LCD Digital Single View Color Monitor (3 Channel) RVS-97 Reverse With Confidence ™ 1
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before Beginning Installation . . . . . . . . . . . . . . . . . . . . . . Monitor Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trigger Introduction. . . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. INTRODUCTION The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life. Be sure to obey all applicable local traffic and motor vehicle regulations as it pertains to this product. Improper installation will void manufacturer’s warranty. SAFETY INFORMATION USAGE: 4 • The Rear View Camera System is designed to help the driver safely detect people and/or objects helping to avoid damage or injury.
INSTALLATION: • Electric shock or product malfunction may occur if this product is installed incorrectly. or disconnected wire may cause a fire. • If smoke or a burning smell is detected, disconnect the system immediately. • Do not install the monitor where it may obstruct drivers view or obstruct an air bag device. SAFETY INFORMATION • While installing the Rear View System be careful with the wire positioning in order to avoid wire • Use this product within the voltage range specified. Failure damage.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot/moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly. Step 1: Choose the monitor and camera locations. BEFORE YOU BEGIN Step 2: Install all cables in vehicle, when necessary a 0.
MONITOR INTRODUCTION Monitor Introduction 2 3 1 4 5 6 7 1) Digital Color LCD Screen 2) Power Indicator/Remote Control Sensor 3) Power Switch 4) Toggle Brightness Down 5) Toggle Brightness Down 6) Channel Selection 7) Menu 8) Toggle AV1/AV2/AV3 9) Speaker 10) Mounting Bracket 8 Rear View Safety 8 9 10
Wiring 1 3 2 10 5-9 11 12 4 Reverse With Confidence ™ WIRING 1) To Monitor 2) White 5 Pin Male 3) Blue 5 Pin Male 4) Brown 5 Pin Male 5) Red Power (DC 10-32V) 6) White Wire (Trigger Wire For Left Turn Signal) 7) Black (GND) 8) Blue Wire (Trigger Wire For Left Turn Signal) 9) Brown Wire (Trigger Wire For Reverse) 10) Camera Cable (Not Included) 11) Camera Cable (Not Included) 12) Camera Cable (Not Included) 9
Remote Introduction 2 3 1 4 7 3 5 6 8 REMOTE INTRODUCTION 9 10 11 13 14 12 15 1) MUTE - Enable/disable sound 2) POWER - Turn monitor on/off 3) HORIZONTAL FLIP: Toggle picure horizontally 4) CHANNEL UP: Toggle Selection Up 5) VERTICAL FLIP: Toggle picure vertically 6) BRIGHTNESS DECREASE: Toggle brightness down 10 Rear View Safety
When the white wire is attached to positive left turn signal, the monitor will automatically switch to CAM1 (left side camera) when left turn signal is used.
When the blue wire is attached to positive right turn signal, the monitor will automatically switch to CAM1 (right side camera) when right turn signal is used. TRIGGER INTRODUCTION When the brown wire is attached to reverse signal, the monitor will automatically switch to CAM3 (backup camera) when the vehicle is put into reverse. The distance grid lines will also display. Press M to display the following options and settings.
Picture BRIGHT,CONTRAST, COLOR, VOLUME, AUTO DIM and SCALE ADJUST options will display on the screen as illustrated below: MENU OPTIONS Reverse With Confidence ™ 13
MENU OPTIONS Option LANG , SCALE , CAM1 , CAM2, CAM3 options display on the screen as illustrated on next page.
MENU OPTIONS Reverse With Confidence ™ 15
MENU OPTIONS System Auto Scan 16 Rear View Safety
Troubleshooting TROUBLESHOOTING Reverse With Confidence ™ 17
WARRANTY ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER Reverse With Confidence ™ DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
