Instruction Manual 3.
TABLE OF CONTENTS Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 03 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04-05 Display Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06 System Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07-08 System Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09-10 Reflective Film. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE! Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a RVS-SA150 Heads Up Display With this manual you will be able to properly install and operate the unit. INTRODUCTION Please read the entire manual and follow the instructions and warnings carefully. Failure to do so can cause serious damage and/or injury, including loss of life.
If you have questions about this product, contact: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 1.800.764.1028 SAFETY INFORMATION IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
SAFETY INFORMATION Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot/moving parts and electrical noisy components. We recommend doing a benchmark test before installation to insure that all components are working properly.
DISPLAY FUNCTIONS Display Functions 1) Light sensor 2) Voltage icon 3) Driver fatigue alarm 4) Water temperature Icon 5) Speed unit (KM/H) 6) Speed unit (MPH) 7) RPM (1 circle is 200R) 8) Speaker (can be turned on/off) 9) Speed, water temperature, voltage (can be toggled) 6 Rear View Safety
HUD Installation 1. RVS-SA150 is compatible with ODBII/EUODB vehicles (see below) 2. Find vehicle 16 pin diagnostic link and connect it to the Heads Up Display HUD Function SYSTEM INTRODUCTION 1 2 3 1. OBDII cable input 2. Power button 3. Rotatable Control Switch A. Up button: Move control switch up B. Ok button: Press button C.
Vertically short press button: Toggle water temperature, voltage, and speed icons Pull down setting button (5 seconds): toggle alarm volume on/off Reset setting: When the HUD is off long press the setting button/turn on HUD on. This resets settings SYSTEM INTRODUCTION Clear the fault code: Turn on the HUD and waiting for it scans the OBD2 program successfully,long pull up the setting button,full screen will be on, and it means clear the fault codes completed.
Menu Parementers Adjustement Range Explanation Default State Display Speed 50-150 2 Brightness 0-5 Adjustment 3 Water Temp 50-150 Alarm 4 Low Voltage 100-150 Alarm 5 RPM Alarm 10-75 6 Speed Alarm 0-199 Move up/ down to toggle speed 107 0: Auto brightness 5: Brightest Alarm will alert user when temp reaches 120 Alarm will alert user when voltage is less than 11v HUD gives alarm when over 5000 rmp If default value is changed, there are 3 levels of alarms (50, 80, 120) 0 Reverse With Confidence
SYSTEM ADJUSTMENT Menu Parementers Adjustement Range Explanation Default State Display 10 7 Driver Fatigue 0-10 8 Speed Unit 1-2 9 Power on Voltage 0-150 10 Delayed Shutdown 10-180 0 is off. 4 4 will give user an alarm every 4 hours 1: KM 1 2: MPH If HUD can- 0 not power off, adjust to 13.2 14.
Reflective Film Installation Follow these instructions if a double image appears when installed. 1.Place the mounting mat in the desired position on the dashboard with the HUD on top. 2.Observe where the HUD reflects & place the reflective film in position. Reverse With Confidence ™ REFLECTIVE FILM A. Ensure the surface is clean and dry before installing the film B. Remove the back protective side marked (1) and attach the film to the clean windscreen C.
TROUBLESHOOTING Troubleshooting 1. No display Start the car engine, check if the OBD cable line. Test car OBD diagnostic interface. 2. When HUD power on, HUD only shows the car voltage and auto powers off after 30 seconds HUD just available for OBD2/EU-OBD vehicles 3.Difficult to see HUD Check if HUD host surface protective film is torn. Toggle brightness. 4. Inaccurate data Reset device 5. Inaccurate Speed a. Confirm speed unit b.
6. Setting for Automatic start/stop system The default value for HUD shutdown time is 10 seconds. When the car is gas-electric hybrid and automatic start/stop system, you can delay the shutdown time in menu 10 (Between 10 seconds to 180 seconds.) If still not working set voltage at 13.2v or 13.6v, which automativally turns off when the car voltage is less then 13.2v. 7. HUD cannot power off or HUD can power off but re-starts Change the menu 9 value to any of one between 13.2V and 140V.
WARRANTY ONE YEAR WARRANTY REAR VIEW SAFETY, INC. WARRANTS THIS PRODUCT AGAINST MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM DATE OF PURCHASE. WE RESERVE THE RIGHT TO REPAIR OR REPLACE ANY SUCH DEFECTIVE UNIT AT OUR SOLE DISCRETION. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR A DEFECT IN THE SYSTEM AS A RESULT OF MISUSE, IMPROPER INSTALLATION, DAMAGE OR MISHANDLING OF THE ELECTRONIC COMPONENTS. REAR VIEW SAFETY, INC. IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES OF ANY KIND.
DISCLAIMER Reverse With Confidence ™ DISCLAIMER REAR VIEW SAFETY AND/OR ITS AFFILIATES DOES NOT GUARANTEE OR PROMISE THAT THE USER OF OUR SYSTEMS WILL NOT BE IN/PART OF AN ACCIDENT OR OTHERWISE NOT COLLIDE WITH AN OBJECT AND/OR PERSON. OUR SYSTEMS ARE NOT A SUBSTITUTE FOR CAREFUL AND CAUTIOUS DRIVING OR FOR THE CONSISTENT ADHERENCE TO ALL APPLICABLE TRAFFIC LAWS AND MOTOR VEHICLE SAFETY REGULATIONS.
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 Better Cameras. Better Service. IT’S OUR GUARANTEE.
