Installation Manual

ManualsBrandsRVS Systems ManualsAnalog CamerasRVS System Backup Camera For Jeep Wrangler

INSTALL A T ION(INSTR U C T IO N S (

8848 Instructions 12-18-14.docx Page 1 of 5

Jeep Wrangler Adjustable Rear Vision Camera, 2007 – Current

(Kit # 9002-8848)

Items Included in the Kit

Camera

Chassis Harness

Power Harness

Zip lock bag with 15 Wire Ties & 3 Push Nuts

Camera Extension Bracket

These Instructions

Required Tools & Supplies

T15 & T20 Torx Bits

7mm & 10mm Sockets

Phillips Screwdriver

3/8” Wrench or Socket Drive

Plastic Trim Removal Tool

Soldering Iron, Solder, & Heat Shrink Tubing

(RECOMMENDED) or T-taps as an alternate

splicing method

Electrical Tape

Install Camera

Step 1: Loosen lug nuts to remove spare tire.

Step 2: Slide Camera on studs placing harness end

inside of tire carrier.

Step 3: Adjust Camera head to fit your specific wheel.

Bracket is shipped in factory wheel configuration.

Adjustment Bracket for Camera Clearance using Phillips

Screwdriver and 3/8” Wrench or Socket Drive

Note: Short Bracket has been designed for Factory

offset wheels. Use the Long Bracket for wheels with

larger offsets.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Jeep Wrangler Adjustable Rear Vision Camera, 2007 – Current (Kit # 9002-8848) Items Included in the Kit Required Tools & Supplies Camera Chassis Harness Power Harness Zip lock bag with 15 Wire Ties & 3 Push Nuts Camera Extension Bracket These Instructions T15 & T20 Torx Bits 7mm & 10mm Sockets Phillips Screwdriver 3/8” Wrench or Socket Drive Plastic Trim Removal Tool Soldering Iron, Solder, & Heat Shrink Tubing (RECOMMENDED) or T-taps as an alternate splicing method Elect
PAGE 2
INSTALLATION INSTRUCTIONS Step 4: Remove spare tire and slide (3) supplied Push Nuts on the studs. Step 8: Pull harness through the rear gate openings. Step 9: Use supplied Wire Ties to secure Chassis Harness to existing harness. Step 5: Reinstall spare tire. Install Chassis Harness Step 6: Insert connector from Camera connector through the rear gate vent behind tire carrier. Step 10: Use supplied Wire Ties to secure Chassis Harness to existing harness.
PAGE 3
INSTALLATION INSTRUCTIONS Step 12: Use a T20 Torx bit to remove subwoofer box. Step 13: Using a plastic trim removal tool, pry off rear seat belt closeout. Step 17: Run Chassis Harness under B-pillar cover to passenger door sill. Use a plastic trim removal tool to remove the (2) plastic push pins and remove passenger sill plate/kick panel. Step 14: Using a plastic trim removal tool, remove rear access panel to expose 10mm bolt, and remove bolt. Step 18: Remove rubber bin insert from top of dash.
PAGE 4
INSTALLATION INSTRUCTIONS Step 19: Remove 7mm bolt . Step 22: Remove 7mm bolt. Step 20: Using a plastic trim removal tool, remove window switch panel. Step 23: Remove driver knee bolster cover. Step 21: Disconnect harness from window switches. Step 24: Remove (2) 7mm bolts on both sides of the steering column. Step 25: Remove center stack/cluster surround. 8848 Instructions 12-18-14.
PAGE 5
INSTALLATION INSTRUCTIONS Step 26: Remove glove box for access and run Mirror Harness toward center of dash. Step 29: Connect Chassis Harness to Power Harness . Step 27: Using a plastic trim removal tool, remove HVAC panel. Step 30: Plug the Chassis Harness RCA connector into your aftermarket display. Step 31: Test the system. Start vehicle and shift into Reverse in order to check that all connections were made properly.