OPERATOR’S MANUAL 18 VOLT HEDGE TRIMMER P2600 BATTERIES AND CHARGERS SOLD SEPARATELY Your hedge trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for your purchase.
TABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 �n General Safety Rules ....................................................................................................................................................... 3 �n Specific Safety Rules.............................................................................................................
GENERAL SAFETY RULES n Keep hands, face, and feet at a safe distance from moving parts. Do not touch or try to stop the cutting blades when they are moving. n Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SPECIFIC SAFETY RULES n Before starting the hedge trimmer, make sure the blade is not in contact with any object. MODEL BATTERY PACK (P100) CHARGER (P110) P2600 130255004 1423701, 140237023 or 130224028 or 140237021 n To reduce the risk of explosion and possible injury, DO NOT place battery units or their batteries near fire or heat. n Do not mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.
SAFETY RULES FOR CHARGER n An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
FEATURES PRODUCT SPECIFICATIONS Motor .................................................................. 18 Volt DC Blade Length .............................................................. 18 in. Cutting Capacity........................................................ 3/8 in. Charger Input ................................... 120 V, 60 Hz, AC only Charge Rate ..............................................................1 hour Net Weight.................................................................
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are damaged or missing do not operate this tool until the damaged or missing parts are replaced. Failure to do so could result in possible serious personal injury. n Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
OPERATION NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature range, the red LED on charger will come on.
OPERATION CHARGING A HOT BATTERY PACK P100 BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger.
OPERATION WARNING: Battery tools are always in operating condition. Therefore, switch should always be locked when not in use or carrying at your side. STARTING THE HEDGE TRIMMER See Figure 4. n Remove the blade cover. n Press and hold the trigger lock. n Depress the switch trigger. n Release the trigger lock. Continue to depress the trigger for extended operation. TRIGGER LOCK STOPPING THE HEDGE TRIMMER See Figure 4. n Release the switch trigger to stop the hedge trimmer. SWITCH TRIGGER Fig.
OPERATION OPERATING TIPS See Figures 6 - 7. DANGER �� �� � If blade jams on any electrical cord or line, DO NOT TOUCH THE BLADE! IT CAN BECOME ELECTRICALLY LIVE AND VERY DANGEROUS. Continue to hold the hedge trimmer by the insulated rear handle or lay it down and away from you in a safe manner. Disconnect the electrical service to the damaged line or cord before attempting to free the blade from the line or cord. Failure to heed this warning will result in serious personal injury or possible death. Fig.
MAINTENANCE WARNING: WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. WARNING: Only the parts shown on the parts list are intended to be repaired or replaced by the customer.
MAINTENANCE WARNING: BLADE COVER SCREWS Blades are sharp. When handling the blade assembly, wear non-slip, heavy-duty protective gloves. Do not place your hand or fingers between blades or in any position where they could get pinched or cut. NEVER touch blades or service unit with battery pack installed. REPLACING BLADES See Figures 8 - 9. Periodically inspect the blades for damage and wear. Always use the manufacturer’s specified replacement blades.
MAINTENANCE LUBRICATING THE BLADE See Figure 10. For easier operation and longer blade life, lubricate the hedge trimmer blade before and after each use. n Remove the battery pack from the hedge trimmer. n Lay the hedge trimmer on a flat surface. Apply light weight machine oil along the edge of the top blade. If you will be using the hedge trimmer for an extended period, it is advisable to oil the blade during use. NOTE: Do not oil while the hedge trimmer is running. n Stop the hedge trimmer.
MAINTENANCE CLEANING THE HEDGE TRIMMER n Slide the blade cover over the blade. n Remove the battery pack. n Clean dirt and debris from the body of the hedge trimmer, using a damp cloth with a mild detergent. NOTE: Do not use any strong detergents on the plastic housing or the handle. They can be damaged by certain aromatic oils such as pine and lemon, and by solvents such as kerosene. BLADE COVER n Moisture can cause a shock hazard. Wipe off any moisture with a soft dry cloth.
OPERATOR’S MANUAL 18 VOLT HEDGE TRIMMER P2600 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO.
