OPERATOR'S MANUAL String Trimmer PLT3043E RY70103 Your new trimmer has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual. Thank you for buying a Ryobi trimmer.
TABLE OF CONTENTS ■ Safety ..................................................................................................................................................................... 2 - 3 ■ Symbols ................................................................................................................................................................. 4 - 5 ■ Technical Data .................................................................................................................
SAFETY ■ Secure long hair so it is above shoulder level to prevent entanglement in any moving parts. ■ Keep all bystanders, children, and pets at least 15 m (50 ft.) away. ■ Do not operate this unit when you are tired, ill, or under the influence of alcohol, drugs, or medication. ■ Do not operate in poor lighting. ■ Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance or exposure to hot surfaces. ■ Keep all parts of your body away from any moving part.
SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates danger, warning or caution. It means attention!!! Your safety is involved. Read Your Operator’s Manual Your manual contains special messages to bring attention to potential safety concerns as well as operating and servicing information.
SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
UNPACKING INSTRUCTIONS PACKING LIST FOR OWNER'S KIT ■ Carefully remove the product from the carton. ■ Inspect the product to make sure no breakage or damage occurred during shipping. ■ Do not discard the packing material until you have inspected and operated the product.
ASSEMBLY ASSEMBLY INSTRUCTIONS: HANDLE BASE SCREWS GRASS DEFLECTOR See Figure 2. 1. Remove wing nut, flat washer, lock washer, and bolt from the Owner’s Kit. 2. Place grass deflector over shaft and bracket. 3. Install bolt through the slots in the tabs on grass deflector and bracket on driveshaft housing. 4. Install flat washer, lock washer and wing nut. 5. Tighten Securely. HANDLE BASE GRASS DEFLECTOR BOLT NUTS BRACKET FLAT WASHER LOCK WASHER WING NUT BRACKET SPACER Fig.
ASSEMBLY MUFFLER GUARD ASSEMBLY See Figure 4. 1. Remove muffler guard and two screws from the owner's kit. 2. Attach the muffler guard to the rear housing. NOTE: Make sure the bent end of the muffler guard fits securely into the opening of the rear housing. 3. Using the torx wrench supplied, install the two screws and tighten securely. REAR HOUSING TORX WRENCH SCREWS MUFFLER GUARD BENT END OF MUFFLER GUARD OPENING IN REAR HOUSING Fig.
OPERATION FUEL AND REFUELING WARNING HANDLING THE FUEL SAFELY ■ Always handle fuel with care, it is highly flammable. ■ Always refuel outdoors where there are no sparks and flames. Do not inhale fuel vapors. ■ Do not let gasoline or oil come in contact with your skin. ■ Keep gasoline and oil away from the eyes. If gasoline or oil comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately. ■ Clean up spilled fuel immediately.
OPERATION ADVANCING THE STRING GRASS DEFLECTOR LINE TRIMMING CUTOFF BLADE ADVANCING STRING USING THE EZ LINE™ TAP ADVANCE SYSTEM String advance is controlled by tapping string head on grass while running engine at full throttle. 1. Run engine at full throttle. 2. Tap string head on ground to advance string. String advances each time the head is tapped. 3. Several taps may be required until string strikes the cut off blade. 4. Resume trimming.
OPERATION STARTING AND STOPPING TO START A WARM ENGINE: 1. Lay trimmer on a flat, bare surface. 2. Choke lever should already be in the “WARM START” position. If not, squeeze and release throttle trigger. Pull the starter rope until unit runs. See Figures 8 and 9. NOTE: The unit is equipped with an automatic choke feature. The starting instructions for this feature are different from units with a manual choke. Be sure to read and follow the starting instructions below.
MAINTENANCE 6. Make sure the string head and the spool retainer are installed on the drive shaft by turning the retainer clockwise to tighten. 7. Pull the strings again to rotate the spool into cutting position. Push the spool retainer down while pulling on string(s) to manually advance the string and to check for proper assembly of the string head. WARNING: Use only original manufacturer's replacement parts, accessories and attachments.
MAINTENANCE STRING REPLACEMENT See Figures 12, 13, 14 and 15. 1. Stop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer. Turn counterclockwise. 2. Remove the spool from the string head. NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool. 3. Cut two pieces of string, each being approximately 2.7 m (9 ft.) long. 4. Insert the first string into the anchor hole in the upper part of the spool.
MAINTENANCE REPLACING AND CLEANING AIR FILTER LATCH See Figures 16 and 17. For proper performance and long life, keep air filter clean. 1. Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover. 2. Remove the filter, clean it in warm soapy water. Rinse and let dry completely. For best performance, replace annually. 3. Install the filter, align tabs, push in, and make sure the latches are locked into place. PULL COVER TO OPEN Fig.
TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM POS SIBLE CA USE POSSIBLE CAUSE SOLUTION Engine will not start: 1. No spark. 1. Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the starter rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug. 2. Push primer bulb until bulb is full of fuel.
TROUBLESHOOTING IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER. PROBLEM POS SIBLE CA USE POSSIBLE CAUSE SOLUTION Grass wraps around driveshaft housing and stringhead: 1. Cutting tall grass at ground level. 2. Operating trimmer at part throttle. 1. Cut tall grass from the top down. Spool retainer hard to turn: Screw threads dirty or damaged. Clean threads and lubricate with grease - if no improvement, replace spool retainer. Oil drips from muffler: 1.
WARRANTY GUARANTEE – STATEMENT (RTSA / RTUK / RTG) All Ryobi products are guaranteed from defects in material and workmanship, for a period of twenty-four (24) months, effective and evidenced from date of original invoice or delivery note. Defects caused by normal wear and tear, unauthorized/improper maintenance/handling or overload are excluded from this guarantee as are accessories such as battery packs, bulbs, blades and bits,etc.
OPERATOR'S MANUAL String Trimmer PLT3043E RY70103 Ryobi Technologies GmbH Itterpark 7 D-40724 Hilden Germany Tel.: +49 (0)2103 / 29 58 0 Fax : +49 (0)2103 / 29 58 29 info@ryobi-rtg.