Operator`s manual

ManualsBrandsRyobi ManualsPower Tool4060300

WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this

product.

OPERATOR'S MANUAL

LONG MITER/RIP FENCE KIT

4060300

FOR USE WITH RYOBI BT3000, BT3100 AND

BT3100-1 TABLE SAWS

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your new Long Miter/Rip Fence kit has been engineered and manufactured to Ryobi's high standard for dependability,

ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

Thank you for buying a Ryobi accessory kit.

THIS KIT MAKES EITHER A LONG MITER FENCE OR A LONG RIP FENCE FOR USE WITH BT3000, BT3100 AND BT3100-1 TABLE SAW

TABLE SAW IS NOT INCLUDED WITH THIS KIT

LONG RIP FENCE

LONG MITER FENCE

Summary of content (10 pages)

PAGE 1
OPERATOR'S MANUAL LONG MITER/RIP FENCE KIT 4060300 FOR USE WITH RYOBI BT3000, BT3100 AND BT3100-1 TABLE SAWS THIS KIT MAKES EITHER A LONG MITER FENCE OR A LONG RIP FENCE FOR USE WITH BT3000, BT3100 AND BT3100-1 TABLE SAW LONG MITER FENCE LONG RIP FENCE TABLE SAW IS NOT INCLUDED WITH THIS KIT Your new Long Miter/Rip Fence kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety.
PAGE 2
TABLE OF CONTENTS         Introduction....................................................................................................................................................................... 2 Rules For Safe Operation ................................................................................................................................................. 2 Symbols...................................................................................................................
PAGE 3
SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
PAGE 4
UNPACKING Your new long miter/rip fence kit includes a 41 in. extension rail, plus the necessary brackets, and connecting hardware required to assemble a long miter fence and attach it to the sliding miter table of your BT3000/BT3100/BT3100-1 table saw. It also includes connectors and hardware required for attaching a long rip fence to your saw.  Remove the parts from the box. Make sure that all items listed in the loose parts list are included.
PAGE 5
TOOLS NEEDED You need an adjustable wrench and phillips screwdriver to assemble this accessory. ADJUSTABLE WRENCH #2 PHILLIPS SCREWDRIVER ASSEMBLY  Slide the locator pin into the bottom channel of the long miter fence rail. Note: The locator pin assembled to the miter fence provided with your BT3000/BT3100/BT3100-1 table saw is assembled identical to this assembly. This locator pin fits in either hole "A" or hole "B" when mounting the long miter fence to the sliding miter table.
PAGE 6
ASSEMBLY ASSEMBLE THE SAW GAGES SQUARE HEAD BOLT (1/2 in.) See Figure 3.  Place a saw gage into each end of the long miter fence rail. Correct orientation of the saw gage to the rail is important. Align the slot in the saw gage with the slot in the rail. MITER/RIP FENCE RAIL (LONG MITER FENCE RAIL) 1/4 in. WASHER KNOB NUT  Secure both saw gages to the rail with the plastite screws provided. The long miter fence rail has drilled holes on the bottom at each end.
PAGE 7
ASSEMBLY MITER/RIP FENCE RAIL (LONG MITER FENCE RAIL) ADJUSTING KNOB MITER FENCE HOLDER SLIDING MITER TABLE RIGHT POSITIVE STOP BRACKET SUPPORT BRACKET LEFT POSITIVE STOP BRACKET SLOT 5/16 in. WASHER SQUARE HEAD BOLT (1/2 in.) HEX BOLT (7/8 in.) KNOB NUT WORK SUPPORT BRACKET 1/4 in. WASHER 5/16 in. WASHER KNOB BOLT Fig. 4 LONG MITER FENCE ASSEMBLY SHOWN ATTACHED TO A BT3000/BT3100/BT3100-1 TABLE SAW Fig.
PAGE 8
ASSEMBLY This kit also includes connectors and hardware required for attaching a long rip fence to your saw. If you have been using this kit as a long miter fence, it will be necessary to remove all connectors, brackets, hardware, etc. If you are assembling for the first time, proceed as follows. HEX BOLT (1/2 in.) ASSEMBLE THE LONG RIP FENCE CONNECTOR 5/16 in. WASHER See Figures 6, 7, and 8.
PAGE 9
RYOBI LONG MITER/RIP FENCE KIT NO. 4060300 Now that you have purchased your Long Miter/Rip Fence Kit, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. 4 7 6 8 5 3 9 2 10 11 4 1 15 14 17 Key No.
PAGE 10
OPERATOR'S MANUAL LONG MITER/RIP FENCE KIT 4060300 FOR USE WITH RYOBI BT3000, BT3100 AND BT3100-1 TABLE SAWS • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.