3 5 7 9 OWNER’S OPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NO. HP61 THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER. Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator’s manual before using your new cordless drill-driver.
TABLE OF CONTENTS ■ Table Of Contents/Typical Applications. .......................................................................................2 ■ Rules For Safe Operation ........................................................................................................ 3-5 A. Precautions On Using Your Cordless Tool .............................................................................4 B. Important Safety Instructions For Charger ............................................................
RULES FOR SAFE OPERATION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
RULES FOR SAFE OPERATION (Continued) 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. when working outdoors. Wear protective hair covering to contain long hair and keep it from being drawn into nearby air vents. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. PROTECT YOUR LUNGS. Wear a face mask or dust mask if operation is dusty. PROTECT YOUR HEARING. Wear hearing protection during extended periods of operation. SECURE WORK.
RULES FOR SAFE OPERATION (Continued) 7. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and c.
OPERATION SPECIFICATIONS: Switch Two-Speed No Load Speed 300/500 RPM Clutch 24 Positions Charger Input 120V, 60 Hz, AC only Charge Rate 3-6 Hours 7 DC Motor 6.0V BIT STORAGE AREA 5 Motor 1 3 3/8 in. Keyless LEVEL 9 Chuck TORQUE ADJUSTMENT RING SWITCH TRIGGER KNOW YOUR DRILL-DRIVER DIRECTION OF ROTATION SELECTOR KEYLESS CHUCK See Figure 1. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. Fig.
OPERATION IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES REVERSE DIRECTION OF ROTATION SELECTOR 1 3 5 7 When using your drill-driver continuously, the batteries become hot. You should let the batteries cool down for approximately 30 minutes before attempting to recharge. Note: This situation occurs when continuous use of your drill-driver causes the batteries to become hot. It does not occur under normal circumstances. Refer to "Charging Your Drill-Driver" for normal recharging of batteries.
OPERATION KEYLESS CHUCK RELEASE (UNLOCK) See Figure 4. A keyless chuck has been provided with your drill to allow for easy installation and removal of bits. As the name implies, you can hand tighten or release drill bits in the chuck jaws. Grasp and hold the collar of the chuck with one hand. Rotate the chuck body with your other hand. The arrows on the chuck indicate which direction to rotate the chuck body in order to GRIP (tighten) or RELEASE (unlock) the drill bit.
OPERATION REMOVING BITS SCREWDRIVING 9 TO DECREASE TORQUE 3 5 7 TORQUE ADJUSTMENT RING 1 See Figure 5. ■ Place the direction of rotation selector in center position. This will turn off the power to your drill. ■ Loosen the chuck jaws from drill bit. ■ To loosen: grasp and hold the collar of the chuck with one hand, while rotating chuck body with your other hand. Note: Rotate chuck body in the direction of the arrow marked RELEASE to loosen chuck jaws.
OPERATION WARNING: Always wear safety goggles or safety glasses with side shields when operating tool. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. DRILLING 21 23 WARNING: 19 See Figure 10. When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off center as the hole is started.
OPERATION CHUCK REMOVAL MALLET KEYLESS CHUCK 9 CHUCK JAWS 1 3 5 7 See Figures 11, 12, and 13. The chuck must be removed in order to use some accessories. To remove: ■ Lock the switch trigger by placing the direction of rotation selector in center position. ■ Insert a 5/16 inch or larger hex key wrench into the chuck of your drill and tighten the chuck jaws securely. ■ Tap the hex key wrench sharply with a mallet in a clockwise direction. See Figure 11.
MAINTENANCE BATTERIES Your drill is equipped with Nickel-Cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. The batteries in this tool have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble your drill and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.
BATTERY REMOVAL DISPOSAL OF EXHAUSTED BATTERIES C YC R ER B R CL E To preserve natural resources, please recycle or dispose of batteries properly. DRILL HANDLE 37 1.8 This product contains nickel-cadmium battery. Local, state, or federal laws may N i Cd prohibit disposal of Nickel-Cadmium 00 .822.88 batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/or disposal options. For more information on battery recycling call 1-800-8 BATTERY.
OWNER'S OPERATOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NO. HP61 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please refer to the Service Center insert or call 1-800-525-2579 in the United States or 1-800-265-6778 in Canada for your nearest Authorized Service Center. You can also check our web site at www.ryobi.