OPERATOR’S MANUAL MANUEL D’UTILISATION MANUAL DEL OPERADOR GARAGE DOOR OPENER OUVRE-PORTE DE GARAGE SISTEMA DE APERTURA PARA PORTÓN DE GARAJE GD200 HomeLink® and the HomeLink® house icon are registered trademarks of Gentex Corporation. HomeLink® et l’image de maison HomeLink® sont des marques déposées de Gentex Corporation. HomeLink® y el icono de la casa de HomeLink® son marcas comerciales registradas de Gentex Corporation.
TABLE OF CONTENTS TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO Introduction....................................................................................................................................................................... 2 Introduction / Introducción Specific Safety Rules.........................................................................................................................................................
SPECIFIC SAFETY RULES WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THIS GARAGE DOOR OPENER to reduce the risk of electric shock, fire and/or serious personal injury. For use with residential sectional or single-panel garage doors. Not for commercial use. Only enable the RYOBI Garage Door Opener Module System App feature when installed with a sectional door. Know your product. Read operator’s manual carefully.
SPECIFIC RULES FOR BATTERY OPERATION When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire. Use battery operated products only with specifically designated battery packs. Use of any other battery packs may create a risk of fire. Do not dispose of the batteries in a fire.
SAFETY RULES FOR CHARGER IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - DANGER: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK CAREFULLY FOLLOW THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the GD200 garage door opener. 2. Before using garage door opener, read all instructions and cautionary markings on garage door opener, battery, and product using battery. 3. CAUTION: To reduce the risk of injury, charge only lithium-ion rechargeable batteries.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Direct Current Type or a characteristic of current Alternating Current Type of current No Load Speed Rotational speed, at no load Per Minute Revolutions, strokes, surface speed, orbits etc.
ELECTRICAL ELECTRICAL CONNECTION This product has a precision-built electric motor. It should be connected to a power supply that is 120 volts, AC only (normal household current), 60 Hz. Except with battery pack installed, a substantial voltage drop will cause a loss of power and the motor will overheat. If your product does not operate when plugged into an outlet, double-check the power supply. GROUNDING INSTRUCTIONS See Figure 1. This product must be grounded.
FEATURES PRODUCT SPECIFICATIONS Module Capacity......................................................up to 7 Max Garage Door Height.............................................7 ft.* Bulb Type..................................................................... LED Drive Type........................................................... Belt Drive Input......................................... 120V AC, 60 Hz. or 18V DC Motor.......................................................................
FEATURES Wire Terminal (Sensor) Wire Terminal (Keypad) Wi-Fi Antenna Module Port #2 Module Port #7 Battery Door RF Antenna AC Receptacle Module Port #1 Brackets Rail Assembly Module Port #3 Console Door Module Port #4 Module Port #5 10 - English AC Receptacle Module Port #6 Fig.
FEATURES Module Port #6 Module Port Cover Module Port #7 Module Port #5 Battery Port Battery Door Console Door Motion Sensor Outdoor Keypad Indoor Keypad Light Cover Safety Sensor (2) Car Remote (2) Fig.
FEATURES KNOW YOUR GARAGE DOOR OPENER See Figures 3 - 5. The safe use of this product requires an understanding of the information on the product and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. AC RECEPTACLE The garage door opener has two 120 Volt AC GFCI protected receptacles with a combined rating of 10 Amps.
LOOSE PARTS B A C G F E D I H K J Child can become trapped or pinned under an automatic garage door resulting in serious injury or death. • Do not allow children to walk or run under a closing door. • Do not allow children to operate door opener controls. • Always keep a closing door within sight. • In the event a person is trapped under the door, push the control button or use the emergency release. • This operator system is equipped with an unattended operation feature.
LOOSE PARTS The following items are included with your garage door opener: A. Header Bracket...................................................................................................................................................... 1 B. Wing Nut................................................................................................................................................................ 2 C. Mounting Strap.......................................................................
TOOLS NEEDED The following tools (not included or drawn to scale) are needed for assembly and adjustments: 3/16 in. Drill Bit Socket Bit (10, 11, and 13 mm) Level Flat Head Screwdriver Rubber Mallet Adjustable Wrench Phillips Head Screwdriver Socket Wrench (10, 11, and 13 mm) Wire Stripper Drill 6 or 7 Foot A-Frame Ladder Tape Measure Pliers Hammer Pencil Hacksaw 2 x 4 board (1 ft.) Fig.
ASSEMBLY WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1 when assembling and performing maintenance on this product. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. Insert the edge of the end rail into the sleeve. Slide together until rail clicks in place. If you cannot get the rail to fit by hand, try gently tapping it with a rubber mallet until it is snug and clicks into place.
ASSEMBLY Move the front pulley toward the middle of the front rail. Insert the edge of the front brace into the front rail. Slide together until brace clicks in place. If you cannot get the brace to fit by hand, try gently tapping it with a rubber mallet until it is snug. Pull the front pulley forward and slide the rod through the hole in the brace. Install spring and tension nut onto pulley rod. Move the inner and outer trolley to the middle of the rail assembly.
ASSEMBLY ADJUSTING THE BELT TENSION See Figures 18 - 21. Using a 13 mm socket, turn the tension nut clockwise to tighten the belt and counter-clockwise to loosen it. Adjust the nut until there is approximately 3/8 to 1/2 in. of exposed thread showing above it or until the base of the nut is aligned with the edge of the brace. When properly tensioned, there should be about a 1/8 in. gap between the belt and the edges of the intermediate rail near the center of the rail assembly.
ASSEMBLY Place the sprocket onto the motor shaft with the round side of the sprocket facing up. Hold the rail assembly above the power head with arrow pointing toward the front of the power head and the garage door. Front of Power Head Rotate the rail assembly until the opening in the rail is aligned with the sprocket. Wi-Fi Antenna Lower the end rail onto the sprocket with the channel (open end) facing down. Slowly rotate the rail to the correct orientation as you lower it into position. Fig.
INSTALLATION IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of injury to persons – Only enable the RYOBI Garage Door Opener Module System App feature when installed with a sectional door. WARNING: TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: 1. R E A D A N D F O L L O W A L L I N S TA L L AT I O N INSTRUCTIONS. 2. Install only on a properly balanced garage door. An improperly balanced door could cause severe injury.
INSTALLATION CHECK THE CONDITION OF THE DOOR AND IDENTIFY THE SPRING TYPE See Figure 26 - 28. Half-Open Position WARNING: If the garage door does not move smoothly, binds, or is out of balance, have it repaired or replaced by a qualified service person. An unbalanced or damaged garage door may not reverse on command, which can result in death or serious personal injury. Sectional Door NOTICE: The garage door opener may not function as intended if installed onto an unbalanced garage door.
INSTALLATION INSTALLING THE HEADER BRACKET 2 x 4 board. The 2 x 4 board can be installed between two studs or into masonry using lag screws and concrete anchors (not supplied). See Figures 29 - 31. Locate the following items: WARNING: Header Bracket To avoid serious personal injury, attach header bracket to sound structural support on header wall. NEVER install the header bracket into weak surfaces such as drywall that can cause the header bracket to fall.
INSTALLATION Stand on a ladder near the garage door as someone slowly raises it. While it’s moving, find and mark the highest point of travel along the center line. The high point will vary based on the type and construction of your garage door, but typically it will be 10-12 inches above the top of the door. WARNING: Use extreme care when standing on a ladder. Ensure someone is holding the ladder on the ground to keep it stable.
INSTALLATION ATTACHING RAIL ASSEMBLY TO HEADER BRACKET Angle the rail assembly so that it rests against the header bracket. NOTE: If a door spring or other obstruction is in the way, have someone hold the garage door opener or help to balance it on a raised support while you position the rail assembly. See Figure 32. Locate the following items: Large Clevis Pin Hitch Pin Place the power head on top of a prop or on the ground with a towel or packaging material beneath it.
INSTALLATION MOUNTING THE POWER HEAD TO THE CEILING See Figures 33 - 38. Lower the garage door completely. Measure the space between the header bracket and the ceiling. NOTE: For unfinished ceilings, measure the space between the header bracket and the nearest joists on either side. WARNING: Mount garage door opener to sound structural support on ceiling. NEVER mount the garage door to drywall or false ceiling grids.
INSTALLATION To mount the power head to finished ceilings: Install center bracket or brackets (not supplied) to the nearest joists or other structural supports in garage ceiling using lag screws (not supplied). Using a hack saw, cut pieces of the mounting straps that are a half inch longer than the measured length between the header bracket and the ceiling. NOTE: Mounting straps that will be attached diagonally should be cut longer than the vertical measured distance in figure 33.
INSTALLATION POSITIONING THE RF ANTENNA Lower the garage door completely. See Figure 39. Insert one end of the emergency release rope through the hole in the handle and tie a knot at the bottom. Remove the tape securing the RF antenna. Carefully move the antenna so it hangs below the opener. NOTE: If the RF antenna is not positioned below the opener, the signal reception between the opener and the outdoor keypad or car remotes may be weakened.
INSTALLATION Mark the middle holes on the left and right of the bracket. Secure the bracket in place by installing self-tapping screws in the center holes on the left and right sides of the bracket. Tighten screws with a 10 mm socket. NOTE: For wooden doors, drill hole completely through the door and install bracket using bolts (not provided) and nuts (not provided), see figure 42. To install the bracket on single-panel doors: Lower the garage door completely.
INSTALLATION CONNECTING DOOR BRACKET TO OUTER TROLLEY To connect sectional doors: Lower the garage door completely. See Figures 45 - 50. Locate the following items: Pull the emergency release rope down and slide outer trolley toward the garage door. Secure straight door arm to the rear of the outer trolley using medium clevis pin and hitch pin. Curved Door Arm Straight Door Arm Secure curved door arm to the door bracket using small clevis pin and hitch pin.
INSTALLATION To connect single-panel doors: Lower the garage door completely. Pull the emergency release rope down and slide outer trolley toward the garage door. Place the curved and straight arms together and align the holes. Choose two sets of aligned holes and install bolts and nuts. Tighten bolts and nuts with a 13 mm socket. WARNING: DO NOT operate the garage door opener unless the safety sensors are installed and working correctly.
INSTALLATION NOTE: The top of the sensor should be between four and six inches above the floor. NOTE: The receiving sensor has a green LED. Ensure that the lens on this sensor is not exposed to direct sunlight. Mark the position of the hole in the bracket. Secure brackets in place using nails or drill 3/16 in. pilot holes and secure with lag screws. Tighten screws with an 11 mm socket.
INSTALLATION Twist the white wires from both sensors together and insert them into the left terminal marked with W. For alignment instructions, see Aligning The Safety Sensors in the Operations section. Wires (Striped) WARNING: Make sure the keypad is mounted high enough to prevent unauthorized activation of the garage door opener. It should be placed at least five feet above the floor so that it is inaccessible to children.
INSTALLATION Insert a flat head screwdriver into the tabs on the indoor keypad and remove the back cover. Insert the white wire into the right terminal marked with W. Hold the back cover against the wall. Use a pencil and a level to mark screw hole placement. Mount the back cover to the wall using screws. Install screws using Phillips screwdriver. NOTE: Use screws and drywall anchors when installing the keypad into drywall.
INSTALLATION INSTALLING THE OUTDOOR KEYPAD See Figures 62 - 64. Locate the following items: Outdoor Keypad Outdoor Keypad Pencil Screws (1.5 in., Phillips Hd.) [2] WARNING: Do not use garage door opener if keypads or remotes do not start and stop the motor. An opener that cannot be controlled with a keypad or remote is dangerous, can result in death or serious personal injury, and must be repaired. Key Hole Screwdriver Top Screw WARNING: Fig.
OPERATION IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: WARNING: Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to cause death or serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious death or personal injury. 1. READ AND FOLLOW ALL INSTRUCTIONS. 2.
OPERATION CHARGING A BATTERY PACK NOTICE: This product is designed to be powered by either a RYOBI ONE+™ 18V lithium-ion (Li-ion) battery pack (DC mode) or by electric power (AC mode). The unit will operate in AC mode whenever it is connected to an electric power source. It will switch to DC mode when an approved battery pack is installed and the unit is not connected to an AC power source. CONNECTING THE GARAGE DOOR OPENER TO A POWER SUPPLY See Figures 65 and 66.
OPERATION INSTALLING MODULES See Figures 67 and 68. The garage door opener can power a variety of AC and DC modules. For a complete list of modules, visit www.ryobitools.com. NOTE: If the garage door opener is unplugged and a charged battery pack is installed, the AC receptacles and module ports will be disabled but the sensors and LED lights will continue to function normally. Hooks WARNING: Use only recommended accessories listed on our website, in this manual, or in addendums.
OPERATION ALIGNING THE SAFETY SENSORS NOTICE: See Figure 69 - 70. The garage door will not close unless the safety sensors are installed, wired, and aligned correctly. WARNING: DO NOT operate the garage door opener unless the safety sensors are installed and working correctly. Failure to properly install and ensure that the safety sensors are working correctly can result in death or serious personal injury.
OPERATION receiving sensor. The most common cause of interference is direct sunlight. If necessary, remove the fasteners securing the sensor and move it away from the garage door opening to avoid sunlight. If the red LED light is ON and the green LED light is off, then the sensors may need to be aligned.
OPERATION SAFETY SENSOR DIAGNOSTIC FEEDBACK LED FUNCTIONS RED LED (TRANSMITTER) GREEN LED (RECEIVER) ON ON OFF OFF OFF ON ON ON PROBLEM SOLUTION No problem indicated No action required Power head is unplugged or the battery is depleted Wires from power head may be damaged Wires not connected Wires connected to the wrong terminal One or both sensors are defective Connect to power supply or charge the battery pack Replace damaged or broken wires One or both sensors are defective Contact custo
OPERATION SETTING THE DOOR TRAVEL LIMITS See Figures 71 - 78. DANGER: Ensure that the safety sensors are installed and working properly. Without the proper safety devices in place, a closing garage door could kill or seriously injure someone in its path. The console on your garage door opener makes it easy to set the open and close positions of your door. The opener will automically sense the weight of your door and provide the force required to open and close it.
OPERATION NOTICE: Do not open or close the garage door using the indoor keypad or remotes until the travel limits have been properly set. Doing so could cause severe damage to the garage door or the garage door opener. Correct (Fully Open Position) Before setting the travel limit: Pull the emergency release rope down and manually open the garage door until the outer trolley engages the inner trolley. Once you begin setting the travel limits, you have two minutes to complete each step.
OPERATION To set the travel limit for the closed position: Press and hold the DOWN button for three seconds. After you release the button, it will begin blinking and continue blinking until the travel limit has been set. Set Press and hold the DOWN button to move the garage door to the closed position. Down Up For fine adjustments, press and release the UP or DOWN buttons. Once the door is in the closed position, press the SET button to program the travel limit.
OPERATION USING THE INDOOR KEYPAD can only be controlled using the indoor keypad and smart phone. The unit will not respond to car remotes or the outdoor keypad. See Figure 79. NOTE: The LEDs in the indoor keypad will blink when the unit is in vacation mode. WARNING: Keep moving door in sight when using indoor keypad. Contact with moving door can cause DEATH or serious injury. The indoor keypad has backlights that turn on when garage door opener is connected to a power supply.
OPERATION TESTING THE AUTOMATIC REVERSAL SYSTEM See Figure 80. DANGER: Test the automatic reversal system every month and after any adjustments are made to the garage door travel limits. If the door contacts an object higher than 1-1/2 in. off the garage floor (approx. the size of a 2x4 laid flat), it should stop and reverse to the fully open position. If the automatic reversal system does not function properly, a closing garage door could kill or seriously injure someone in its path.
OPERATION PROGRAMMING THE OUTDOOR KEYPAD See Figures 81 - 82. WARNING: Program Keep moving door in sight when using outdoor keypad. Contact with moving door can cause DEATH or serious injury. Once you begin programming the outdoor keypad, you have two minutes to complete each step. If a step is not completed within two minutes, programming information will be erased. For best results, stand beneath the garage door opener when programming the keypad.
OPERATION PROGRAMMING THE CAR REMOTES Visor Clip See Figure 83. Car Remote WARNING: Keep moving door in sight when using car remotes. Contact with moving door can cause DEATH or serious injury. Once you begin programming the car remotes, you have two minutes to complete each step. If a step is not completed within two minutes, programming information will be erased. Press the PROGRAM button on the garage door opener’s console.
MAINTENANCE IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: WARNING: Before inspecting, cleaning or servicing the machine, lower the garage door, shut off motor, wait for all moving parts to stop, disconnect unit from power supply, and remove all modules. Failure to follow these instructions can result in serious personal injury or property damage. WARNING: When servicing, use only identical replacement parts.
MAINTENANCE REPLACING CAR REMOTE BATTERIES Reassemble the remote by aligning the sections as shown. See Figure 85. Snap the sections together to close. Make sure the remote is securely reassembled before attaching the visor clip. WARNING: KEEP BUTTON/COIN CELL BATTERIES OUT OF SIGHT AND REACH OF CHILDREN. Swallowing batteries can lead to serious injury or death. If you suspect a child has ingested a battery, go to the hospital immediately.
ACCESSORIES The following accessories are not included with your garage door opener but may be available where you purchased this product. For assistance call 1-877-205-5714. Extension Kits........................................................................................................GDAEXT100 (8 ft.), GDAEXT110 (10 ft.), GDAEXT112 (12 ft.), and GDAEXT114 (14 ft.) Carbon Monoxide Alarm...........................................................................................................
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION When programming the outdoor keypad, a buzzer sounds and all console buttons blink seven times. A step for programming the outdoor keypad was not completed within two minutes. Complete each step for programming the outdoor keypad within two minutes. When programming a car remote, a buzzer sounds and all console buttons blink seven times. A step for programming the car remote was not completed within two minutes.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Garage door cannot be opened or closed with car remote or outdoor keypad The garage door opener is in Vacation Mode. Press the LOCK ( ) button on the indoor keypad or smart phone app to unlock the garage door opener Garage door opener is loud or noisy Fasteners may not be tightened securely Inspect the entire product for loose parts such as screws, nuts, bolts, caps, etc.
WARRANTY LIMITED WARRANTY STATEMENT One World Technologies, Inc., warrants to the original retail purchaser that this RYOBI™ brand garage door opener is free from defect in material and workmanship and agrees to repair or replace, at One World Technologies, Inc.’s discretion, any defective product or part free of charge for the following time periods starting from the date of purchase. Three years for the power head, gearbox, rails, door arms, sensors, remotes, and keypads.
FCC COMPLIANCE The following FCC compliance information is for the GD200 garage door opener only. For information regarding other products, like modules and accessories, refer to the labels and documentation included with those items. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC rules.
OPERATOR’S MANUAL / GD200 GARAGE DOOR OPENER MANUEL D’UTILISATION / OUVRE-PORTE DE GARAGE DE GD200 MANUAL DEL OPERADOR / SISTEMA DE APERTURA PARA PORTÓN DE GARAJE DE GD200 To request service or purchase replacement parts: Visit www.ryobitools.com or call 1-877-205-5714 If any parts or accessories are damaged or missing, do not return this product to the store. Call 1-877-205-5714 for immediate service. Please obtain your model and serial number from the product data plate.
