OPERATOR'S MANUAL Orbital Scrolling Jig Saw with Laser JS550L Your new jig saw has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product.
TABLE OF CONTENTS n Introduction ...................................................................................................................................................................... 2 n General Safety Rules.....................................................................................................................................................3-4 n Specific Safety Rules ...............................................................................................................
GENERAL SAFETY RULES n Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents. n Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury. n Do not overreach. Keep proper footing and balance at all times.
GENERAL SAFETY RULES n When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. SERVICE n Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ELECTRICAL DOUBLE INSULATION EXTENSION CORDS Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the tool will draw.
FEATURES PRODUCT SPECIFICATIONS Input ............................................................................................................................. 120 Volts, 60 Hz, AC Only, 5.5 amps No Load Speed ....................................................................................................................................................0-3200/min. Stroke Length.............................................................................................................................
FEATURES KNOW YOUR JIG SAW BLADE SUPPORT ROLLER See Figure 1. Before attempting to use this product, familiarize yourself with all operating Features and Safety Rules. The blade support roller reduces blade flexing to ensure accurate cutting. SWITCH Four position orbital adjustment for fine to aggressive cutting. ORBITAL ADJUSTMENT KNOB The jig saw has a conveniently located trigger switch.
UNPACKING PACKING LIST This tool has been shipped completely assembled except for the blade. n Carefully remove the tool and accessories from the box. n Make sure that all items listed in the packing list are included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping. n Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. n If any parts are damaged or missing, please call 1-800-525-2579 for assistance.
OPERATION WARNING: LOCK-ON BUTTON Do not allow familiarity with your tool to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating this tool. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
OPERATION VARIABLE SPEED See Figure 5. The saw has a variable speed control selector designed to allow operator control and adjustment of speed and power limits. The speed and power of your saw can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 5. NOTE: Hold the saw in normal operating position and turn the variable speed control selector to the positive symbol to increase speed and power.
OPERATION STRAIGHT CUT See Figures 7 - 9. Your saw is equipped with a lock for locking the scrolling knob in the forward facing position. This should be locked for all straight cuts as shown in figure 8. A straight cut can be made by clamping a piece of wood or straightedge to the workpiece and guiding the edge of the saw against it. Make the cut from one direction only. Don't cut halfway and complete the cut from the opposite end. You can also use the supplied edge guide as shown in figure 8.
OPERATION SCROLL CUTTING See Figures 10, 11, and 12. The scroll cutting feature is designed to permit 360° rotation of the saw blade so that intricate designs may be cut with minimum effort. n Set the orbit adjustment to “0”. n� Loosen the base locking lever as shown in figure 10. n� Slide the base back to move the blade-support roller out of the way of the saw blade as shown in figure 11. �n Retighten the base locking lever.
OPERATION ANGLE CUTTING (BEVEL CUTTING) See Figures 13 and 14. Bevel cutting angles may be adjusted from 0° to 45° right or left. Angles for cuts from 0° to 45° in 15° increments are marked on a scale on both the left and right side of the base. An arrow under the motor assembly provides an indicator at each of the above mentioned 15° increments. A protractor is recommended when accurate cuts are required. n Unlock the base by moving the base locking lever forward.
OPERATION PLUNGE CUTTING See Figures 15, 16, and 17. WARNING: To avoid loss of control, broken blades, or damage to the material being cut, always use extreme caution when making plunge cuts. We do not recommend plunge cutting on materials other than wood. TO MAKE A PLUNGE CUT n Mark the line of cut clearly on the workpiece. � Set the orbit adjustment to “0”.
ADJUSTMENTS WARNING: BASE PLATE SCREWS Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury. BASE PLATE BASE LOCKING LEVER ADJUSTMENT See Figures 18 and 19. The base locking lever may need occasional adjustment. It may be necessary to tighten the lever. n Unplug the saw. �n If attached, remove the vacuum attachment.
ADJUSTMENTS LASER GUIDE ADJUSTMENT See Figure 20. NOTE: Draw a pencil line on a scrap workpiece parallel to the long edge of the base as a straight line guide to aid in the adjusting process. n Unplug the jig saw. WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. n If the laser guide is on the right side of the line, turn the laser adjustment screw counter clockwise one half of a turn.
MAINTENANCE WARNING: WARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc. come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, which may result in serious personal injury.
OPERATOR'S MANUAL Orbital Scrolling Jig Saw with Laser JS550L • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO.