OPERATOR’S MANUAL 10 in. Table Saw RTS10 Your table saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this product. Thank you for your purchase.
table of contents Introduction.......................................................................................................................................................................2 Warranty............................................................................................................................................................................2 General Safety Rules..............................................................................
GENERAL SAFETY RULES SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool. DON’T OVERREACH. Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. DISCONNECT TOOLS. When not in use, before servicing, or when changing attachments, blades, bits, cutters, etc.
GENERAL SAFETY RULES STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush. DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. USE ONLY CORRECT BLADES. Do not use blades with incorrect size holes. Never use blade washers or blade bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).
SPECIFIC SAFETY RULES NEVER perform any operation “freehand” which means using only your hands to support or guide the workpiece. Always use either the rip fence or miter gauge to position and guide the work. NEVER stand or have any part of your body in line with the path of the saw blade. NEVER reach behind, over, or within three inches of the blade or cutter with either hand for any reason. MOVE THE RIP FENCE out of the way when cross cutting.
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Safety Alert Indicates a potential personal injury hazard. Read Operator’s Manual To reduce the risk of injury, user must read and understand operator’s manual before using this product. Eye Protection Always wear eye protection marked to comply with ANSI Z87.1.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ELECTRICAL Extension Cords SPEED AND WIRING Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat.
GLOSSARY OF TERMS Anti-Kickback Pawls (radial arm and table saws) A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation. Arbor The shaft on which a blade or cutting tool is mounted. Bevel Cut A cutting operation made with the blade at any angle other than 90° to the table surface. Compound Cut A cross cut made with both a miter and a bevel angle.
FEATURES PRODUCT SPECIFICATIONS Input......................................................................15 Amps No Load Speed..................................... 5,000 r/min. (RPM) Cutting Depth at 0°....................................................... 3 in. Cutting Depth at 45°...............................................2-5/8 in. Blade Arbor............................................................... 5/8 in. Blade Diameter........................................................... 10 in.
FEATURES HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on the front of the cabinet, use this handwheel to lower and raise the blade for height adjustments or blade replacement. This handwheel also makes the adjustment for bevel angles easy. KNOW YOUR TABLE SAW See Figure 2. The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting.
FEATURES Operating Components WARNING: The upper portion of the blade projects up through the table and is surrounded by an insert called the throat plate. The height of the blade is set with a handwheel on the front of the cabinet. To accommodate wide panels, the saw table has rails on each side. Detailed instructions are provided in the Operation section of this manual for the basic cuts: cross cuts, miter cuts, bevel cuts, and compound cuts.
FEATURES BLADES WARNING: For maximum performance, it is recommended that you use the 24-tooth, 10 in. carbide-tipped combination blade provided with your saw. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local dealer can provide you with complete information. Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.
LOOSE PARTS The following items are included with the table saw: d c e b f A g M L h K j I Fig. 5 A. B. C. D. E. F. G. Anti-Kickback Pawls................................................. 1 Blade Guard.............................................................. 1 Switch Key................................................................ 1 Handle....................................................................... 1 Miter Gauge..............................................................
LOOSE PARTS The following items are included with the table saw leg stand: I G D C C D E I F E B H A A E I B H H F I H A. Lower Brace...............................................................2 B. Lower Side Brace.......................................................2 C. Upper Brace...............................................................2 D. Upper Side Brace.......................................................2 E. Hex Nut........................................................
ASSEMBLY UNPACKING WARNING: This product requires assembly. Carefully lift saw from the carton and place it on a level work surface. NOTE: This tool is heavy. To avoid back injury, keep your knees bent and lift with your legs, not your back, and get help when needed. Do not lift the saw without help. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.
ASSEMBLY TO ASSEMBLE THE LEG STAND See Figure 7. Assembly is best done in the area where the saw will be used. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s). CARRIAGE Bolt upper brace Hex Nut Take the following from a small hardware pack: 16 bolts (1/4 - 20 x 1/2 in.) 16 hex nuts (1/4 - 20) Take 4 legs and 8 braces from loose parts.
ASSEMBLY to install the Handle See Figure 9. Hold the nylon nut securely and turn the screw counterclockwise to remove the nut completely. NOTE: Do not remove the screw from the handle. Place the nylon nut into the recessed hole on the back of the height/bevel adjusting handwheel and hold in place. Slide the handle, screw, and washer into the hole on the height/bevel adjusting handwheel. Using a flathead screwdriver, turn the screw clockwise and tighten in place.
ASSEMBLY to CHANGE BETWEEN A spreader AND A riving knife release lever (UNLOCKED) See Figure 12. This saw is shipped with the spreader/riving knife placed in the non-through cutting or “down” position (riving knife position). NOTE: The spreader/riving knife must be placed in the through cutting, or “up” position (spreader position), for all other cutting operations. Unplug the saw. To place in spreader position (or “up” position for all through cutting): Remove the throat plate.
ASSEMBLY TO check SAW BLADE installation OPEN END blade wrench See Figure 13. caution: CLOSED END blade wrench blade nut To work properly, the saw blade teeth must point down toward the front of the saw. Failure to do so could cause damage to the saw blade, the saw, or the workpiece. Unplug the saw. Lower the saw blade and remove the throat plate. Make sure the bevel locking lever is securely pushed to the right.
ASSEMBLY TO INSTALL THE BLADE GUARD AND ANTIKICKBACK PAWLS BLADE guard See Figures 14 - 16. guard LEVER WARNING: Replace dull or damaged anti-kickback pawls. Dull or damaged pawls may not stop a kickback increasing the risk of serious personal injury. NOTE: Anti-kickback pawls should only be installed for through cuts. Unplug the saw. Raise the saw blade by turning the height/bevel adjusting handwheel clockwise. Fig. 14 Place spreader/riving knife in “up” position.
ASSEMBLY TO Check and Align the spreader/riving knife and Saw Blade hex key See Figures 17 - 18. To check alignment of the spreader/riving knife: Unplug the saw. Raise the saw blade by turning the height/bevel adjusting handwheel clockwise. Remove the anti-kickback pawls and blade guard assembly. Place a framing square or straight edge against both the saw blade and the spreader. Note: Place framing square between carbide teeth and measure from blade.
ASSEMBLY PUSH STICK STORAGE push stick storage SCREW(S) See Figure 19. Insert the push stick storage screws from the loose parts bag into the holes on the side of the saw table. Use a Phillips head screwdriver to tighten screws securely. Place the slots in the push stick over the screws and slide the push stick toward the back of the saw. PUSH STICK Fig.
OPERATION from the workpiece and may contact the blade. Kickback can cause serious injury. Use precautions to avoid the risks. Kickback can be caused by any action that pinches the blade in the wood such as: WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1.
OPERATION cutting aids See Figure 20. Push sticks are devices that may be used for pushing a workpiece through the blade in any rip cut. When making non-through cuts or ripping narrow stock, always use a push stick, push block, and/or featherboard so your hands do not come within 3 inches of the saw blade. They can be made in various sizes and shapes from scrap wood and used in a specific project.
OPERATION FEATHERBOARD WARNING: A featherboard is a device used to help control the workpiece by holding it securely against the table or fence. Featherboards are especially useful when ripping small workpieces and for completing non-through cuts. The end is angled with a number of short kerfs to give a friction hold on the workpiece and locked in place on the table with a C-clamp. Test to ensure it can resist kickback. Mount the featherboard in front of the saw blade.
operation types of cuts See Figure 25. There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6) the compound (bevel) miter cut. All other cuts are combinations of these basic six. Operating procedures for making each kind of cut are given later in this section. 1 Cross Cut WARNING: Always make sure the blade guard and anti-kickback pawls are in place and working properly when making these cuts to avoid possible injury.
operation TO CHANGE BLADE DEPTH gullet See Figure 26. The blade depth should be set so that the outer points of the blade are higher than the workpiece by approximately 1/8 in. to 1/4 in. but the lowest points (gullets) are below the top surface. Turn the bevel lock lever to the right. Raise the blade by turning the height/bevel adjusting handwheel clockwise or lower it by turning the handwheel counterclockwise. Fig. 26 TO CHANGE BLADE ANgle (BEVEL) 90º adjustment SCREW See Figure 27.
operation WARNING: clamp screw To reduce the risk of injury, always make sure the rip fence is parallel to the blade before beginning any operation. locking lever TO use the Rip Fence See Figure 29. Place the rear lip on the rear of the saw table and pull slightly toward the front of the unit. Lower the front end of the rip fence onto the guide surfaces on top of the front rail. With the rip fence flat on the saw table, push the fence towards the front rail to align the fence to the saw table.
operation TO use the miter gauge See Figure 30. The miter gauge provides greater accuracy in angled cuts. For very close tolerances, test cuts are recommended. MITER GAUGE BODY There are two miter gauge grooves, one on either side of the blade. When making a 90° cross cut, you can use either miter gauge groove.
operation heeling (paralleling) the blade to the miter gauge groove See Figures 32 - 34. adjusting SCREWS WARNING: RIGHT MITER gauge GROOVE COMBINATION SQUARE The blade must be parallel to the miter gauge groove so the wood does not bind resulting in kickback. Failure to do so could result in serious personal injury. Do not loosen any screws for this adjustment until you have checked with a square and made test cuts to be sure adjustments are necessary.
operation MAKING CUTS CROSS CUT This table saw can perform a variety of cuts that are not all mentioned in this manual. DO NOT attempt to make any cuts not covered here unless you are thoroughly familiar with the proper procedures and necessary accessories. Your local library has many books on table saw usage and specialized woodworking procedures for your reference.
operation making a RIP cut RIP CUT See Figure 37. BLADE RIP FENCE WARNING: Make sure the blade guard assembly is installed and working properly to avoid serious possible injury. Set the blade to the correct depth for the workpiece. Position the rip fence the desired distance from the blade for the cut and securely lock the handle. Make sure the wood is clear of the blade before turning on the saw.
operation making a bevel cross cut VIEWED FROM THE FRONT, BELOW THE TABLE SAW See Figures 39 - 40. TO LOOSEN WARNING: TO TIGHTEN Make sure the blade guard assembly is installed and working properly to avoid possible serious injury. Remove the rip fence. Unlock the bevel locking lever. Adjust the bevel angle to the desired setting. Lock the bevel locking lever. Set the blade to the correct depth for the workpiece. Set the miter gauge to 0° and tighten the lock knob.
operation Position the workpiece flat on the table with the edge flush against the rip fence. Let the blade build up to full speed before feeding the workpiece into the blade. BEVEL RIP CUT RIP FENCE BLADE ANGLED Once the blade has made contact with the workpiece, use the hand closest to the rip fence to guide it. Make sure the edge of the workpiece remains in solid contact with both the rip fence and the surface of the table.
operation making a NON-THROUGH cut NON-THROUGH CUT See Figure 43. BLADE GUARD REMOVED WARNING: DO NOT install dado blades on this machine. The arbor shaft has insufficient threads to mount a dado blade. Mounting a dado blade could result in the risk of serious personal injury. Non-through cuts (made with a standard 10 in. blade) can be made with the grain (ripping) or across the grain (cross cut). The use of a non-through cut is essential to cutting grooves.
ADJUSTMENTS WARNING: closed end blade WRENCH OPEN END blade WRENCH Before performing any adjustment, make sure the tool is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury. The table saw has been adjusted at the factory for making very accurate cuts. However, some of the components might have been jarred out of alignment during shipping.
ADJUSTMENTS TO SET the blade at 0° and 45° 0° adjustment screw See Figures 47 - 49. The angle settings of the saw have been set at the factory and, unless damaged in shipping, should not require setting during assembly. After extensive use, they may need to be checked. 45° adjustment SCREW Unplug the saw. Raise the blade. If the blade is not perfectly vertical (0°): Loosen the adjustment screw and the bevel locking lever. Place a combination square beside the blade on the left.
ADJUSTMENTS TO CHECK THE ALIGNMENT OF THE RIP FENCE TO THE BLADE framing square See Figure 50. Unplug the saw. Raise the locking lever to permit the rip fence to be moved. Place a framing square beside the blade and move the rip fence up to the square. Take the dimension on the rip scale. Move the fence back and turn the framing square 180° to check the other side. If the two dimensions are not the same, loosen the two bolts on the fence and align it. Retighten the two bolts.
TROUBLESHOOTING Problem Cause Solution Blade is out of balance. Replace blade. Blade is damaged. Replace blade. Saw is not mounted securely. Tighten all hardware. Work surface is uneven. Reposition on flat surface. Blade is warped. Check saw blade installation. Replace blade if necessary. Rip fence not mounted correctly. Remount the rip fence. Rails are dirty or sticky. Clean and wax rails. Clamp screw is out of adjustment. Adjust clamp screw counterclockwise.
Troubleshooting Problem Saw does not make accurate 90˚ or 45˚ cuts. Cause Solution Positive stops inside cabinet need adjusting (Bevel Cuts). Adjust positive stops. Miter gauge is misaligned (Miter Cuts). Adjust the miter gauge. Height/bevel adjusting handwheel is hard to turn. Gears or screw post inside cabinet are clogged with saw dust. Clean the gears or screw post. Saw does not start. Motor cord or wall cord is not plugged in. Plug in motor cord or wall cord. Circuit fuse is blown.
OPERATOR’S MANUAL 10 in. Table Saw RTS10 WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber.