Replacement Part List

11 in. WATER BROOM
RY31211
WARNING:
To reduce the risk of injury, user must read and understand the opera-
tor’s manual for their pressure washer before using this accessory.
To reduce the risk of injury or property damage, spray the pressure
stream in a safe direction to ensure proper connection of all accesso-
ries before starting any cleaning project. Fits most pressure washers.
Ensure compatibility and proper fit before using this accessory. Wear
eye protection with side shields marked to comply with ANSI Z87.1.
Risk of fluid injections; do not point at people, pets, electrical devices
or the unit itself. Turn off the pressure washer before changing or ad-
justing accessories. For cold water use only. Save these instructions.
Refer to them frequently and use them to instruct other users. If you
loan someone this tool, loan them these instructions also.
SYMBOLS
Some of the following symbols may be used on this product. Please
study them and learn their meaning. Proper interpretation of these
symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert
Indicates a potential personal injury
hazard.
Read Operator’s
Manual
To reduce the risk of injury, user
must read and understand operator’s
manual before using this product.
Eye Protection
Always wear eye protection with side
shields marked to comply with ANSI
Z87.1.
Risk of Injection
To reduce the risk of injection or injury,
never direct a water stream towards
people or pets or place any body part in
the stream. Leaking hoses and fittings
are also capable of causing injection
injury. Do not hold hoses or fittings.
Kickback
To reduce the risk of injury from kick-
back, hold the spray wand securely
with both hands when the machine
is on.
PRODUCT SPECIFICATIONS
Connections ...............................................1/4 in. Quick Connect Plug
Broom Width ................................................................................11 in.
Maximum Pressure .................................................................3,300 psi
Maximum Water Flow .............................................................. 3.0 gpm
Maximum Water Temperature ..................................................... 140°F
INSTALLING THE WATER BROOM ON THE SPRAY WAND
See Figure 1.
Insert the water broom inlet plug into the spray wand quick connect
coupler and secure.
USING THE WATER BROOM
See Figures 2 - 4.
n Once the water broom is installed, connect the hose to the pressure
washer as described in your pressure washer manual.
n Start the pressure washer as described in your pressure washer
manual.
n Pull the pivot knob out and move the pivot coupler back or forward
to achieve the desired nozzle orientation.
A
B
C
A
B
A
B
 Use with the nozzles pointed down and forward (pivot coupler in
back position) to wash large flat surfaces like sidewalks or drive-
ways. Walk slowly behind the water broom, cleaning as you go.
WARNING:
To reduce the risk of injection or injury, never lift the water broom while
operating the pressure washer.
 Pivot so the nozzles are pointed upward (pivot coupler in forward
position) to clean the underside of raised items like your car’s
undercarriage.
WARNING:
To reduce the risk of injection or injury, do not depress the trigger until
the water broom nozzles are completely underneath the surface being
cleaned, and always release the trigger before removing the water
broom from underneath the surface
NOZZLE MAINTENANCE
See Figure 5.
When shipped, the nozzles are pre-assembled to the water broom.
These nozzles are appropriate for use with pressure washers operating
at 2300 to 3300 psi with a maximum flow rate of 3.0 gpm.
Excessive pump pressure (a pulsing sensation felt while squeezing the
trigger and/or a higher vibration in the water broom) may be the result
of a clogged or dirty nozzle.
NOTE: Never point the nozzles at your face.
nTurn off the pressure washer and shut off the water supply. With the
water broom on the ground, pull trigger to release water pressure.
nDisconnect water broom from spray wand.
nUsing a straightened paper clip or fine needle, free any foreign ma-
terials clogging or restricting the nozzle.
nRemove high pressure filter as described in the next section, then
use a garden hose to flush any debris out of nozzles by running the
water through the nozzle openings into the water broom and allowing
debris to drain out through the water broom’s inlet plug.
nReinstall high pressure filter as described in the next section and
tighten securely.
nReconnect the water broom to the spray wand.
nTurn on the water supply and start the pressure washer.
CHANGING THE HIGH PRESSURE FILTER
See Figure 6.
Once you have cleaned the nozzles, if the water still doesn’t flow freely,
it may be necessary to replace the high pressure filter.
To replace the filter:
n Disconnect the water broom from the spray wand.
n Place a flat head screwdriver in the slot in the water broom’s inlet
plug and turn counterclockwise. This will allow the filter to be lifted
out of the machine.
n Once the filter is removed from the inlet plug, replace it with a new
filter (not included).
n Using a flat head screwdriver, turn the filter clockwise until it can no
longer be seen over the top of the inlet plug.
REPLACEMENT PARTS
The following replacement parts may be ordered by calling our customer
service department at 1-800-860-4050:
High Pressure Filter ............................................................. 308103010
3/4 in. Retaining Ring (2) ..................................................... 694723003
O-Ring (4.5 mm ID x 1.8 mm CS) ........................................ 570742132
A - Inlet plug (fiche d’entrée, clavija de entrada de la unidad)
B - Quick connect coupler (coupleur rapide, collarin accíonado por resorte)
Fig. 1
Fig. 3
Fig. 4
Fig. 5
A - Straightened paper clip (trombone droit, clip para papel abierto)
B - Nozzle (buse, boquilla)
C - Spray bar (barre de pulvérisation, tubo rociador)
Fig. 6
A - Inlet plug (fiche d’entrée, clavija de entrada de la unidad)
B - High pressure filter (filtre haute pression, filtro de alta presión)
TECHTRONIC INDUSTRIES
POWER EQUIPMENT
1428 Pearman Dairy Road, Anderson, SC 29625, USA
1-800-860-4050 n www.ryobitools.com
995000130
12-21-16 (REV:01)
Fig. 2
A - Pivot knob (bouton de
pivotement, perilla pivot)
B - Pivot coupler (coupleur de
pivotement, acoplador pivot)
A
B
PIVOT COUPLER BACK
TOURNER LE COUPLEUR
VERS L’ARRIÈRE
GIRE EL ACOPLADOR
HACIA ATRÁS
PIVOT COUPLER FORWARD
TOURNER LE COUPLEUR VERS L’AVANT
GIRE EL ACOPLADOR HACIA ADELANTE