OPERATOR’S MANUAL MANUEL D’UTILISATION MANUAL DEL OPERADOR ELECTRIC POLE SAW SCIE ÉLECTRIQUE DE MANCHE ELÉCTRICA SIERRA DE PÉRTIGA RY43160 ALL VERSIONS TOUTES LES VERSIONS TODAS LAS VERSIONES Your pole saw has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
TABLE OF CONTENTS TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO Introduction........................................................................................................................................2 Introduction / Introducción Important Safety Instructions......................................................................................................... 3-4 Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes Specific Safety Rules................
IMPORTANT SAFETY INSTRUCTIONS WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. READ ALL INSTRUCTIONS For safe operation, read and understand all instructions before using this product. Be familiar with all controls and proper use of the machine. Follow all safety instructions. Failure to follow all safety instructions listed below, can result in serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS edges, or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 16 is recommended for an extension cord 50 feet or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
SPECIFIC SAFETY SAFETY RULES RULES SPECIFIC Maintain product with care. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect cord periodically and, if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease. Check damaged parts.
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME EXPLANATION Safety Alert Symbol Indicates a potential personal injury hazard. To reduce the risk of injury, user must read and understand operator’s manual before using this product. Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with head protection.
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
ELECTRICAL DOUBLE INSULATION Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded. It is possible to tie the extension cord and power cord in a knot to prevent them from becoming disconnected during use.
FEATURES PRODUCT SPECIFICATIONS Bar Length........................................................................................................................................ 8 in. Chain Pitch.....................................................................................................................................3/8 in. Chain Type....................................................................................... Low Profile Skip Tooth Narrow Kerf Input.....................................
FEATURES KNOW YOUR POLE SAW See Figure 2. The safe use of this product requires an understanding of the information on the product and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. LOCK-OUT BUTTON To help prevent accidental starting, the lock-out button must be depressed along with the switch trigger.
ASSEMBLY BUTTON HANDLE POLE LOWER COLLAR THREADED BASE CORD INTERMEDIATE POLE BUTTON UPPER COLLAR THREADED BASE POWERHEAD POLE Fig. 3 CONNECTING THE POLES See Figure 3. Before using the pole saw, a one-time assembly is required. When removed from the box, the three poles are connected by an electrical cord as shown above. n Remove the four (4) rubber cord protectors from inside the poles. This material protects the cord during shipping and MUST be discarded immediately.
OPERATION ADDING BAR AND CHAIN LUBRICANT DANGER: Never cut near power lines, electric cords, or other electric sources. If bar and chain jams on any electrical cord or line, DO NOT TOUCH THE BAR OR CHAIN, THEY CAN BECOME ELECTRICALLY LIVE AND VERY DANGEROUS! Continue to hold the pole saw by the insulated rear handle or lay it down and away from you in a safe manner. Disconnect the electrical service to the damaged line or cord before attempting to free the bar and chain from the line or cord.
OPERATION CONNECTING TO POWER SUPPLY See Figure 5. This product is designed with a cord retainer that prevents the extension cord from being pulled loose while using. n Form a loop with the end of the extension cord. n Insert loop portion of extension cord through opening in the bottom of the rear handle and place over cord retainer. n Slowly pull loop against cord retainer until the slack is removed. n Plug product into extension cord.
OPERATION PREPARATION FOR CUTTING See Figures 7 - 8. n Wear non-slip gloves for maximum grip and protection. n Maintain a proper grip on the unit whenever the motor is running. Use your right hand to firmly grip the rear handle while your left hand has a firm grip on the pole shaft. n Hold unit firmly with both hands. Always keep your left hand on the pole shaft and your right hand on the rear handle, so your body is to the left of the chain line.
OPERATION LIMBING AND PRUNING See Figures 9 - 10. This unit is designed for trimming small branches and limbs up to 6 in. in diameter. For best results, observe the following precautions. n Plan the cut carefully. Be aware of the direction in which the branch will fall. n Branches may fall in unexpected directions. Do not stand directly under the branch being cut. n The most typical cutting application is to position the unit at an angle of 60° or less, depending on the specific situation, as shown.
MAINTENANCE WARNING: FLATS When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage. WARNING: Fig. 11 Always wear eye protection with side shields marked to comply with ANSI Z87.1, along with head protection. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.
MAINTENANCE NOTE: New chain tends to stretch; check chain tension frequently and tension as required. DRIVECASE COVER CHAIN BAR CAUTION: Chain tensioned while warm, can be too tight upon cooling. Check the “cold tension” before next use. BAR NUT REPLACING THE BAR AND CHAIN SPROCKET See Figures 13 - 16. Fig. 13 CHAIN TENSIONING PIN WARNING: To avoid possible serious injury, stop the motor and disconnect from power supply before replacing the bar, chain, or performing any maintenance operation.
MAINTENANCE CHAIN OILER See Figure 17. n Use Premium Bar and Chain Lubricant. It is designed for chains and chain oilers and is formulated to perform over a wide temperature range with no dilution required. n Remove the cap and carefully pour approximately 2 oz. of bar and chain lubricant into the bar lube reservoir. n Replace the cap and tighten securely. n Check and refill the bar lube reservoir every time the pole saw is used. NOTE: Do not use dirty, used, or otherwise contaminated lubricants.
MAINTENANCE HOW TO SHARPEN THE CUTTERS See Figures 19 - 22. Be careful to file all cutters to the specified angles and to the same length, as fast cutting can be obtained only when all cutters are uniform. n Tighten the chain tension enough that the chain does not wobble. Do all of your filing at the midpoint of the bar. Wear gloves for protection. n Use a 5/32 in. diameter round file and holder. n Keep the file level with the top plate of the tooth. Do not let the file dip or rock.
MAINTENANCE STORING THE PRODUCT See Figure 23. Clean all foreign material from the product. Store idle unit indoors in a dry, well-ventilated area that is inaccessible to children. Keep away from corrosive agents such as garden chemicals and de-icing salts. n Always place the scabbard on the saw bar when transporting or storing the pole saw. The scabbard is a snug fit and must be attached very carefully due to the sharp teeth on the saw chain.
WARRANTY LIMITED WARRANTY STATEMENT Techtronic Industries North America, Inc., warrants to the original retail purchaser that this RYOBI® brand outdoor product is free from defect in material and workmanship and agrees to repair or replace, at Techtronic Industries North America, Inc.’s, discretion, any defective product free of charge within these time periods from the date of purchase.
OPERATOR’S MANUAL / ELECTRIC POLE SAW MANUEL D’UTILISATION / SCIE ÉLECTRIQUE DE MANCHE MANUAL DEL OPERADOR / ELÉCTRICA SIERRA DE PÉRTIGA RY43160 WARNING: This product and substances that may become airborne from its use may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive harm. Wash hands after handling.