OPERATOR'S MANUAL 18.0 V Cordless “Six Pack” SPC18 R Your new “Six Pack” has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual. Thank you for buying the Ryobi 18.0 V Cordless “Six Pack.
TABLE OF CONTENTS ■ Introduction ........................................................................................................................................................ 2 ■ Rules For Safe Operation .................................................................................................................................. 3 ■ Symbols .....................................................................................................................................................
RULES FOR SAFE OPERATION ■ READ ALL INSTRUCTIONS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Know your product. Read the operator’s manual carefully. Learn the product’s applications and limitations as well as the specific potential hazards related to this product. Read thoroughly these instructions and the instructions for each tool before using this “Six Pack.” Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL EXPLANATION SAFETY ALERT SYMBOL: Indicates Danger, Warning, or Caution. May be used in conjunction with other symbols or pictographs.
FEATURES LID STORAGE SIDE AND BOTTOM STORAGE The lid provides a work surface and secure storage for the miter saw. Each side of the case provides storage for the miter saw extension rails and the bottom of the case provides storage for the miter saw and circular saw blades. UPPER DRAWER STORAGE MISCELLANEOUS STORAGE The upper drawer provides storage for three battery packs, the battery charger, and the miter saw work clamp.
FEATURES MISCELLANEOUS STORAGE CIRCULAR SAW FLASHLIGHT BATTERY PACKS R UPPER DRAWER RECIPROCATING SAW BATTERY CHARGER LOWER DRAWER DRILL SPEED SAW WOOD BORING BIT STORAGE MISCELLANEOUS SCREWDRIVER STORAGE BIT STORAGE R MITER SAW EXTENSION RAIL STORAGE DRILL BIT STORAGE SCREWDRIVER BIT STORAGE CIRCULAR SAW BLADE STORAGE MITER SAW BLADE STORAGE Fig.
OPERATION SETTING UP THE MITER SAW The MS181 Miter Saw provided in the “Six Pack” has been securely attached to the top lid. This convenient mounting allows a quick and simple set up and stow away procedure. These procedures are illustrated on the top, front surface of the lid for easy reference. See Figure 3. Follow these directions to set up the miter saw. ■ Loosen each lid latch by pulling out on the bottom of the latch, lifting the latch, and then lowering the top of the latch.
OPERATION STORING THE MITER SAW See Figure 4. Follow these directions to store the miter saw. ■ Remove the battery from the saw. ■ Remove the work clamp and any accessories that you have used. ■ Place the saw head in a 90o bevel position and secure the bevel lock. ■ Place the saw in a 90o position to the fence. ■ Lower the saw head and lock it into place. ■ Loosen each lid latch by pulling out on the bottom of the latch and then lowering the top of the latch. (1) ■ Stand in front of the case.
OPERATION ATTACHING THE MITER SAW EXTENSION RAILS R EXTENSION RAILS See Figure 5. Follow these directions to attach the miter saw extension rails. ■ Remove the extension rails from the side storage area. ■ Slide the extension rails into the correct locations on the miter saw. ■ Secure the extension rails using the wing screws provided. OPENING THE FRONT PANEL See Figure 6. Follow these directions to open the front panel. ■ Pull the front panel latches out. ■ Lower the front panel. 30 WING SCREW 22.
OPERATION LIFTING/LOWERING HANDLE See Figure 7. Follow these directions to lift and lower the handle. ■ To lift handle: Push the button located on the top of the handle, pull up the handle, and snap into place. ■ To lower handle: Push the button located on the top of the handle, lower the handle, and snap into place. R WARNING: Always make sure the handle is all the way up and firmly in the locked position before you move the “Six Pack.
MAINTENANCE WARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. GENERAL REPLACEMENT PARTS Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. Top Lid (Part No. 5834101) Front Panel Latches (Part No. 3076701) Lid Latches (Part No. 5100102) Handle (Part No.
OPERATOR'S MANUAL 18.0 V Cordless “Six Pack” SPC18 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our Web site at www.ryobitools.com for a complete list of Authorized Service Centers. • PART NO.
