Owner's manual

ManualsBrandsS&B Filters ManualsAccessories for airCold Air Intake Kit - Cotton Filter 75-5003

2/1/2010

REV-D

(909) 947

-0015 PHONE • (909) 947-0603 FAX

www.sbfilters.com

INSTALLATION INSTRUCTIONS

(OVER)

S&B P/N 75-5003

2005-2006

FORD Mustang GT

4.6L V8

(excluding models

manufactured prior to April of 2005)

Non hydrocarbon absorber equipped

models only.

For 2005 models not equipped with the HC absorber,

permitted Ford intake part numbers 6R33-9C662-BG

(manual trans) or 6R33-9C662-CG (auto trans).

To verify: Locate the label on the front facing vertical

wall of the lower part of the stock air box.

QTY PARTS LIST QTY PARTS LIST (continued)

1 1/2” x 16” Hose 1 #10-24 Pan Head Screws

1 4.5” - 2” Adapter 1 #10-24 Nylock Nuts

1 Intake Tube 2 #10 Washers

1 Air Box 1 Angled Bracket

1 Clear Lid 1 1/2” x 1/4” NPT Hose Barb

1 Air Filter 2 5/16” - 18 Acorn Nuts

2 #72 Hose Clamps 2 5/16” Jam Nuts

2 #8 Rubber Washers 2 5/16” Bolts

1 MAF Sensor Mounting Plate 4 Sealing Washers

1 MAF Sensor Mounting Gasket 4 SS Pan Head Screws

2 #10-32 Pan Head Screws 1 #8 Hose Clamp

2 #8-32 Pan Head Screws

TOOLS REQUIRED

10 mm Wrench &

Socket

1/2” Wrench & Socket

Flat Head Screwdriver

Phillips Screw Driver

T-20 Torx wrench

(supplied)

1. Turn off the ignition and disconnect the

negative battery terminal.

2. Disconnect the crank case vent line from the

intake tube and the valve cover, remove it from

the vehicle.

3. Loosen the hose clamp that attaches the

intake tube to the throttle body.

4. Disconnect the electrical connection from the

MAF sensor

5. Unlatch the air box lid and remove the intake

tube and lid assembly.

6. Remove the OEM panel filter from the air box.

7. Loosen the bolt that secures the air box using

a 10mm socket and ratchet.

8. Pull up and remove the air box from the

vehicle.

9. Remove the grommets from the OE air box.

These will be used to secure the S&B air box.

10. Use the # 8 screws and attach the MAF to the

sensor plate with rubber washers between MAF

and plate. Then attach plate to tube. Point the

arrow on the MAF sensor towards the engine.

11. Carefully install the NPT hose barb into the

intake tube making sure not to cross thread, then

install the 1/2” breather hose onto the hose barb.

Next install the 4” round adapter and hose

clamps to the throttle body end of the tube.

12. Install the S&B Intake Tube on to the throttle

body.

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS S&B P/N 75-5003 QTY 1 2005-2006 PARTS LIST 1/2” x 16” Hose QTY 1 PARTS LIST (continued) #10-24 Pan Head Screws 1 4.5” - 2” Adapter 1 #10-24 Nylock Nuts 1 Intake Tube 2 #10 Washers 1 Air Box 1 Angled Bracket manufactured prior to April of 2005) 1 Clear Lid 1 1/2” x 1/4” NPT Hose Barb Non hydrocarbon absorber equipped models only.
PAGE 2
INSTALLATION INSTRUCTIONS (continued) 18. Secure the air filter to the tube by tightening the hose clamp, then secure the air box “L” bracket. 13. Tighten the hose clamp and secure the tube to the throttle Body. PERFORMANCE TESTING 14. Assemble the air box using the 5/16” hardware. Take the stock grommets from step #9 put them back in the fender before installing the box. 15. Install the “L” bracket short side to the air box, leave loose for adjustment. ∗ Engage parking brake and start your engine.