Operating instructions

ManualsBrandsS&B Lawn Systems ManualsLawn Mower AccessoryLawn StryperLM-408111R

Visit www.patternyourlawn.com

Owner

’

s Manual

Read, Understand and Follow ALL Instructions prior to use.

Lea, entienda y siga todas las instrucciones antes de usar.

S&B Lawn Systems, Inc. / W226N825 Eastmound Drive, Suite B

Waukesha, WI 53186-1690 USA / Visit www.patternyourlawn.com

Model No.

LM–408111B

LM–408111R

LM–408111G

Patent Pending

MADE, ASSEMBLED AND PACKAGED IN AMERICA

S&B Lawn Systems, Inc.

W226N825 Eastmound Drive, Suite B

Waukesha, WI 53186-1690 USA

Printed in the USA

Summary of content (10 pages)

PAGE 1
Owner ’s Manual Visit www.patternyourlawn.com MADE, ASSEMBLED AND PACKAGED IN AMERICA Model No. LM – 408111B LM – 408111R LM – 408111G Patent Pending S&B Lawn Systems, Inc. W226N825 Eastmound Drive, Suite B Waukesha, WI 53186-1690 USA Copyright © 2008 S&B Lawn Systems, Inc. Printed in the USA Read, Understand and Follow ALL Instructions prior to use. Lea, entienda y siga todas las instrucciones antes de usar. MADE, ASSEMBLED AND PACKAGED IN AMERICA S&B Lawn Systems, Inc.
PAGE 2
Safety: Congratulations... • Read, and understand all of the instructions in this manual prior to using the Lawn StryperTM attachment. Follow those instructions whenever using the Lawn StryperTM attachment. • Lawn StryperTM attaches to and follows behind your lawn mower during normal grass-cutting operations, and should not affect the operating characteristics of your mower.
PAGE 3
Lawn Stryper Parts View Assembly: TM • TOOL Required: Phillips Screw Driver. • Roller fills with approx. 16 to 20 lbs. of DRY sand. (sand not included) IMPORTANT: Work on a flat level surface – make certain mower is NOT running. C B A I A B C K I J F F Parts: E A. (2) BSI-LNS-011 Lawn StryperTM Inner Clamp(s) B. (2) BSI-LNS-012 C. (2) Lawn Stryper TM Outer Clamp(s) BSI-LNS-015 Lawn Stryper TM Angle Adjuster(s) D. (1) BSI-LNS-003 Lawn StryperTM Hitch Tube E.
PAGE 4
Step 2 Step 1 Roller Plug Fastener ar This diagram shows the RIGHT-HAND handlebar of the lawn mower. d er H Pour DRY sand into opening. b le n Ha ow n M aw B L K A G Step 2: Attach Inner and Outer Clamps to Handlebars. e Step 1: Fill Roller Assembly With Approximately 16 to 20 lbs. of DRY Sand. Completely fill Roller Tube (G), WITH SAND, via hole located on end of tube. Once completely filled, thread and FULLY TIGHTEN Roller Plug with provided Roller Plug Fastener.
PAGE 5
Step 3 Step 4 r a eb I dl r e ow n aw n Ha M L C A C B F F Step 3: Insert Vertical Tubes into Angle Adjusters. Set Vertical Tube (F) into Angle Adjuster (C). Make certain that top portion of Vertical Tube (F) rests FLAT on inner portion of Angle Adjuster (C) as outlined in above diagram. Screw holes should match up. Insert 2" Pan Head Screw (I) as outlined in above diagram. Step 4: Attach Angle Adjuster Assembly to Handlebar Clamp Assembly.
PAGE 6
Step 5 Step 6 Valco Holes F Lawn Mower Handlebars F Valco Holes Valco Pins E Valco Pins D E 3"- 4" Step 6: Setting Angle and Height. Step 5: Attach Hitch Tube and Corner Tubes to Vertical Mount System. Attach Hitch Tube (D) to Corner Tubes (E) by pressing down on Valco Pins and locking into place as outlined in diagram above. Set width of U-bar assembly (D&E assembled) to coincide with the width of Vertical Bar assembly.
PAGE 7
Step 7 Finished Lawn Stryper TM G D Step 7: - Attach Roller Assembly to Hitch Tube. Attach sand filled Roller Assembly (G) onto Hitch Tube (D) by vertically sliding onto hitch as outlined in above diagram. User Tip! When you don’t want the patterning effect, or perimeter cut is necessary, or when there are obstructions such as fence line, retaining wall, or other objects, remove Roller Assembly (with mower turned off) while keeping tubing and clamp system intact (see helpful tips on page 16).
PAGE 8
Lawn Stryper™ Warranty: General Tips: S&B Lawn Systems, Inc. shall repair any Lawn StryperTM attachment, when used for residential use*, if defective in materials or if it ceases to function due to a failure of it’s components. S&B Lawn Systems, Inc. will repair or replace, at it’s sole discretion, a defective Lawn StryperTM unit. Owner is responsible for shipping costs.
PAGE 9
General Tips Continued: Troubleshooting: Patterning Effect: Roller Does Not Turn: • With mower turned OFF, check to see if any type of debris such as bark, The Lawn StryperTM attachment is specifically designed to properly ‘bend’ grass after it has been cut. This proper ‘bend’ results in light reflecting differently off each side of grass thus producing the pattern effect.
PAGE 10
Lawn Care Tips: Lawn Care Tips Continued: It is important to have a healthy lawn in order to experience all of the benefits Watering Your Lawn: of the Lawn StryperTM attachment. Please find below a few general lawn care tips that will help to ensure a strong and beautiful lawn. Keep Lawn Mower Blade Sharp: A common error is to neglect the lawn mower’s blade.