Motorcycle Accessories User Manual
19
1
2
6
4
5
33
31
18
14
12
11
16
17
12
14
10
7
19
25
27
24
26
13
15
30
29
28
20
25
32
21
23
22
3
9
8
7
1. Bolt, stator 10-24 x1" SHC - 4 required
(HD#2720) (10 Pack). .....................50-0194
2. Seal, sprocket shaft
(HD#12068) ...................................31-4035
3. Bearing, Timken
(HD#9028) ..........31-4013
4. Bolt, case
5/16”" -18 x 3-1/2" HHC - 8 required
(5 Pack) ........................................50-0147
5. Washer, flat
5
⁄
16
" x
11
⁄
16
" x
1
⁄
16
" - 8 required
(10 Pack) ......................................50-7069
6. Bolt center case 1/4" -28 x 5-1/2" HHC
Grade 8 (5 Pack)....................50-0126
7. Washer, flat,
1
⁄
4
" x .474" x .050"
(10 Pack) ......................................50-7076
8. Cylinder studs - 8 required ........31-2325
9. Dowel, cylinder deck - 2 required
(HD#16595-99) (10 Pack) ................50-8179
10. Nut
1
⁄
4
"-28 Grade 8 - 1 required
(10 Pack) ......................................50-5014
11. Bolt, camplate
1
⁄
4
"-20 x 1" SHC - 4 required
(10 Pack) ......................................50-0244
12. Bolt, camplate
1
⁄
4
"-20 x 1
1
⁄
4
" SHC - 2 required
(10 Pack) ......................................50-0153
13. Oring, camplate - 7 required
(HD#11301) (10 Pack) .....................50-8066
14. Dowel, camplate - 2 required
(HD#16589-99). ...............................50-8148
15. Bearing, inner cam
(HD# 9198) .....31-4080
16. Bearing, right main.
2003-up all TC
(HD#24606-00C)......................................N/A
17. Retaining ring, internal, spiraloc,
(HD#35114-02) - 2 required...............50-8160
18. Oring, oil pump
11
⁄
16
" I.D. x
15
⁄
16
" O.D. x
1
⁄
8
"
CS
(HD#11293)...............................50-8039
19. Switch, oil pressure
(HD#26561-99)........................................N/A
20. Plug, sump
(HD#765) ....................50-8330
21. Plug, magnetic drain ..................50-8335
22. Baffle Plate ..................................31-0119
23. Screw 10-24 -3/8" pan head - 2 required
(10 Pack). .....................................50-0139
24. Dowel, case alignment - 2 required
(HD#16574-99) (10 pack) ..............50-8109
25. Oring, case alignment,
9
⁄
16
" I.D. x
11
⁄
16
" O.D. x
1
⁄
6
" CS - 2 required
(HD#26432-76A) (10 Pack) .............50-8102
26. Piston oilers - kit of 2 ..................31-2026
27. Oil line fitting- vent
(HD# 26314-99) ..............................50-8147
28. Oil conduit block .........................31-2076
29. Washer, flat
1
⁄
4
" chrome
(10 Pack).....................................50-7013
30. Bolt,
1
⁄
4
"-20 x 2" HHC - 1 required
....................................................50-0303
31. Hose, oil, inlet/outlet....................50-8157
32. Spring clips - 4 required..............50-8156
33. Oil line fittings, inlet/outlet
2 required ...................................50-8158
O. Replacement Engine Assembly Parts
Use the line drawings to identify replacement parts. Parts designed to fit as direct stock replacements are listed with
corresponding H-D part number. If no H-D part number is shown, S&S part cannot be used in stock application and vice versa
Parts not shown in this diagram, are detailed by other instruction sheets accompanying the Engine.