S2Konnect N-2020T 10/100/1000Base-T Dual Port Server Adapter, PCI-X User Manual S2Konnect N-2020T
Copyright © S2Konnect GmbH, 2010. All rights reserved. This manual refers to the S2Konnect N-2020T Dual Port Server Adapter. Contents are subject to change without notice. Product and brand names are (registered) trademarks of their appropriate owners.
Conventions The following conventions apply to this manual. Warning and Notes Used to indicate a potentially hazardous situation which, if not avoided, could result in death or serious injury. Example: dangerous voltage. ! i Used to indicate a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Example: electrostatic discharge. Used for additional information and advice.
Table of Contents Conventions Warning Notes Safety Precautions Avoiding injuries Avoiding damage 4 4 7 7 7 1 Introduction 8 2 System requirements 8 3 Installation of the S2Konnect N-2020T 10/100/1000Base-T Network Interface Card 8 4 Connection of the S2Konnect Network Interface Card Transmission Distances Connection to the Network 9 9 9 5 Hardware Features Connection options 1.
Table of Figures Figure 1 : Figure 2 : Figure 3 : Figure 4 : Figure 4 : Figure 5 : S2Konnect N-2020T Connection of the RJ-45 / plug Redundancy Link Aggregation Dual Net Connection of Switches Bracket of the N-2020T
Safety Precautions To protect yourself from injuries and avoid damage to your computer and to the S2Konnect N-2020T 10/100/1000Base-T Network Interface Card, always observe the following safety instructions. Avoiding injuries Electrical current! Electrical current from power, phone, and communications cables can be hazardous. Never touch any electrical elements with bare hands.
1 Introduction Thank you for purchasing an S2Konnect product. This document describes the installation of the network adapter card. The N-2020T is a PCI-X adapter which must be installed in a PCI-X slot of the computer. The adapter contains a Network chipset “Marvell 88E8022“ 2 System requirements Computer System: The N-2020T Adapter is a typical server adapter supporting high throughput of data.
4 Connection of the S2Konnect Network Card This chapter describes the physical connection of the S2Konnect N-2020T 10/100/1000Base-T Network Interface Card to a network system. Transmission Distances All ports of the N-2020T are supporting 10/100/1000BaseT connections on Copper Category 5 unshielded twisted pair cable with a maximum distance of 100m.
3. 4. 5. 6. At the other end of the cable connect the connector to the port on the network device. The port type (e.g. 1000Base-T) on the network device and that in the S2Konnect Network Card must be identical. Reconnect the Switch and other units to the power supply. Turn on the network device and the Switch or other station. Check the SPD/LNK/ACT LED belonging to the port you plugged in the plug to find out if the cable is connected correctly.
3. Dual Net LAN 2 LAN 1 Figure 4.
6 Adapter Caracteristics 6.
N-2020T - 10/100/1000Base-T Dual Port Server Adapter, PCI-X, 2 x RJ-45 Product Highlights PCI Low Profile (Bracket included) WoL support Auto MDI/MDI-X Crossover at all speeds and ports Compatible to SysKonnect SK-9S22 Features Ultra Deep RAM, Parity monitoring on all data paths TCP, UDP, and IP checksum generation and checking on chip Jumbo Frame Dynamic Interrupt Moderation Advanced Power Management (ACPI) TCP Segmentation for reducing the CPU Load Promiscuous Mode / Multicast support PXE / RPL Suppo
N-2020T - 10/100/1000Base-T Dual Port Server Adapter, PCI-X, 2 x RJ-45 Standard Compliances IEEE 802.3x with Flow control / Auto-negotiation IEEE 802.1p Quality of Service IEEE 802.3ab Gigabit Ethernet standards IEEE 802.3 and IEEE 802.3u (Ethernet and Fast Ethernet) Driver X86 : Windows 7, Windows Vista, Windows XP, Windows 2000, Windows 2003 (.Net), NT4, Windows98 SE, ME x64 : Windows 7, Windows Vista, Windows XP, Windows 2003 (.
N-2020T - 10/100/1000Base-T Dual Port Server Adapter, PCI-X, 2 x RJ-45 Safety Standards CSA, CB, CE, UL - VCCI EN60950, IEC 60950, VDE 0805 cULus listed accessory (UL 60950, CSA C22.2) EMC CE : EN55022; IEC - CISPR-22 Class B US : FCC, CFR 47 Part 15, Conformity Class B Environment Specifications Storage: -20°C to +70°C, 30% to 80% rel. humidity (non-condensing) Operating: -0°C to +50°C, 10% to 95% rel. humidity (non-condensing) ROHs Compliant with EN 2002/95/EU Power Consumption Single port : @ +3.
6.2 LED’s The LEDs of the S2Konnect N-2020T 10/100/1000Base-T Network Interface Card have the following meaning: 10 (Port B) ACT (Port B) B LINK ACT 1000 100 10 100 (Port B) Port B 1000 (Port B) Port A Figure 5.
7 Important Information Technical Support If you encounter any problems, read the relevant section of the manual. If you cannot solve your problems, consult our technical support. If you contact our technical support engineers, have the following information ready: • switch type • configuration of your network • type of cabling • system documentation Our support team can be reached following the instructions on our website. Please go to www.s2konnect.com, support section.
Appendix A. License and Warranty Information The Americas, Asia, Australia, New Zealand, Pacific Dear Customer, if you acquired your S2Konnect product in the UNITED STATES, CANADA or any other country in the AMERICAS, ASIA, AUSTRALIA, NEW ZEALAND, PACIFIC, the following license and purchase agreement applies to you. This is a legal agreement between you, the end user and S2Konnect based in Ettlingen/Federal Republic of Germany. S2Konnect GmbH.
Europe Dear Customer, if you acquired your S2Konnect product in EUROPE, the following license and purchase agreement applies to you: This is a legal agreement between you, the end user and S2Konnect GmbH, in Ettlingen/Federal Republic of Germany. S2Konnect License and Purchase Agreement By opening the sealed disk package and taking possession of the hardware, you are agreeing to be bound by the terms of this Agreement.
Deutschland, Schweiz, Österreich, Liechtenstein Verehrte Kundin, verehrter Kunde, wenn Sie Ihr S2Konnect Produkt in DEUTSCHLAND, in der SCHWEIZ, in ÖSTERREICH oder in LIECHTENSTEIN erworben haben, gilt für Sie der folgende Lizenz- und Kaufvertrag. Dies ist ein rechtsgültiger Vertrag zwischen Ihnen, dem Endanwender, und der S2Konnect GmbH mit Sitz in Ettlingen/Bundesrepublik Deutschland.
