9-2XUScoverM06.
9-2XUScoverM06.fm Page 2 Tuesday, September 6, 2005 11:12 AM In-car safety There is an In-car safety & Quick Reference Guide found in your car which contains some quick reference concerning safety issues. Make sure you keep this Reference Guide readily available for all occupants to review.
9-2XUScoverM06.fm Page 3 Friday, September 9, 2005 1:48 PM Gas station reference Fuel octane rating Fuel • 2.5-liter non-turbo models Use only unleaded gasoline with an octane rating of 87 AKI or higher. • 2.5-liter turbo models (Aero) Use premium unleaded gasoline with an octane rating of 91 AKI or higher. If premium unleaded gasoline is not available, regular unleaded gasoline with octane rating of 87 AKI or higher may be temporarily used.
9-2XUScoverM06.fm Page 4 Tuesday, September 6, 2005 11:12 AM Saab Automobile AB, Trollhättan, Sweden US/CA MY2006 Ordering nr. 80 33 46. Printed in Sweden on chlorine-free paper 2005-09. © Copyright Saab Automobile AB, 2005. All information and illustrations in this manual are based on the specifications that were available at the time of printing. Model variants, technical data and equipment vary from market to market, and may be altered without prior notice.
A1910BE-A-GSAAB.book Page -1 Tuesday, September 6, 2005 8:37 AM 000169 Introduction This manual provides practical guidance on driving and caring for your Saab 9-2X. Although this manual describes the most important differences between model variants, it does not specify the equipment or features included on individual models. Importation and distribution of Saab automobiles, spare parts and accessories are handled exclusively by Saab Cars USA, Inc.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM 1 Warranties Warranties for U.S.A. All Saab vehicles distributed by Saab of America, Inc. and sold at retail by an authorized Saab dealer in the United States come with the following warranties: Saab Limited Warranty Emission Control Systems Warranty Emissions Performance Warranty All warranty information, including details of coverage and exclusions, is in the “Warranty and Maintenance Booklet”. Please read these warranties carefully.
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 2 Chapter 5: Audio This chapter informs you how to operate your audio system. Chapter 6: Interior equipment This chapter informs you how to operate interior equipment. Chapter 7: Starting and operating This chapter informs you how to start and operate your Saab. Chapter 8: Driving tips This chapter informs you how to drive your Saab in various conditions and explains some safety tips on driving.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM 3 Vehicle symbols Symbol There are some of the symbols you may see on your vehicle.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 4 Symbol Name Door unlock (Transmitter) Safety precautions when driving ¢ Seatbelt and SRS airbag All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Otherwise, the possibility of serious injury becomes greater in the event of a sudden stop or accident.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM 5 ¢ Child safety Never hold a child on your lap or in your arms while the vehicle is moving. The passenger cannot protect the child from injury in a collision, because the child will be caught between the passenger and objects inside the vehicle. While riding in the vehicle, infants and small children should always be placed in the REAR seat in an infant or child restraint system which is appropriate for the child’s age, height and weight.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 6 Carefully read the sections “Child restraint systems”, “*SRS airbag (Supplemental Restraint System airbag)”, and “Seatbelts” in chapter 1 of this owner’s manual for instructions and precautions concerning the child restraint system, seatbelt system and SRS airbag system. ¢ Engine exhaust gas (carbon monoxide) Never inhale engine exhaust gas.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM 7 ¢ Drugs and driving There are some drugs (over the counter and prescription) that can delay your reaction time and impair your perception, judgment and attentiveness. If you drive after taking them, it may increase your, your passengers’ and other persons’ risk of being involved in a serious or fatal accident.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 8 driving. In a collision or sudden stop, unrestrained pets or cages can be thrown around inside the vehicle and hurt you or your passengers. Additionally, the pets can be hurt under these situations. It is also for their own safety that pets should be properly restrained in your vehicle.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags Front seats .......................................................... 1-2 Fore and aft adjustment ......................................... Reclining the seatback ........................................... Seat cushion height adjustment (driver’s seat) ........................................................ Head restraint adjustment ..................................... Active head restraint .................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 1-2 Seat, seatbelt and SRS airbags Front seats Seat, seatbelt and SRS airbags Never adjust the seat while driving to avoid the possibility of loss of vehicle control and of personal injury. Before adjusting the seat, make sure the hands and feet of rear seat passengers are clear of the adjusting mechanism. Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-3 According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning child restraint systems, see the “Child restraint systems” section in this chapter.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 1-4 Seat, seatbelt and SRS airbags ¢ Seat cushion height adjustment (driver’s seat) ¢ Head restraint adjustment ¢ Active head restraint 2 1 100087 100707 1) When the lever is pushed down, the seat is lowered. 2) When the lever is pulled up, the seat rises. The height of the seat can be adjusted by moving the seat cushion adjustment lever up and down. To raise the head restraint, pull it up.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-5 Seat heater 3 Each active head restraint is effective only when its height is properly adjusted and the driver/ passenger sits in the correct position on the seat. If your vehicle is involved in a rear-end collision, have an authorized Saab dealer inspect the active head restraints. The active head restraints may not operate in the event the vehicle experiences only a slight impact in the rear.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 1-6 Seat, seatbelt and SRS airbags Rear seats There is a possibility that people with delicate skin may suffer slight burns even at low temperatures if he/she uses the seat heater for a long period of time. When using the heater, always be sure to warn the persons concerned. Do not put anything on the seat which insulates against heat, such as a blanket, cushion, or similar items. This may cause the seat heater to overheat.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-7 q Rear windows side seating position ¢ Folding down the rear seat q Rear center seating position The head restraint is not intended to be used at the lowest position. Before sitting on the seat, raise the head restraint to the click position. 100098 To raise the head restraint, pull it up. To lower it, push the head restraint down while depressing the release button on the top of the seatback.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 1-8 Seat, seatbelt and SRS airbags place and make sure that it is securely locked. Seatbelts ¢ Seatbelt safety tips 100095 100096 1. Lower the head restraints. 2. Unlock the seatback by pulling the release knob and then fold the seatback down. To return the seatback to its original position, raise the seatback until it locks into All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-9 Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 1-10 Seat, seatbelt and SRS airbags q Expectant mothers 100100 Expectant mothers also need to use the seatbelts. They should consult their doctor for specific recommendations. The lap belt should be worn securely and as low as possible over the hips, not over the waist. ¢ Emergency Locking Retractor (ELR) The driver’s seatbelt has an Emergency Locking Retractor (ELR).
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-11 NOTE If the driver unfastens the seatbelt after fastening, the seatbelt warning device operates as follows according to the vehicle speed. At speeds lower than approximately 9 mph (15 km/h) The warning light will alternate between flashing and steady illumination at 15-second intervals. The chime will not sound.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 1-12 Seat, seatbelt and SRS airbags s Adjusting the front seat shoulder belt anchor height Metallic parts of the seatbelt can become very hot in a vehicle that has been closed up in sunny weather; they could burn an occupant. Do not touch such hot parts until they cool. q Front seatbelts 1. Adjust the seat position: Driver’s seat: Adjust the seatback to the upright position.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-13 When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision. s Unfastening the seatbelt q Rear seatbelts (except rear center seatbelt) 1. Sit well back in the seat. 2.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 1-14 Seat, seatbelt and SRS airbags s Adjusting the rear seat shoulder belt anchor height (window-side seating positions only) q Rear center seatbelt When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-15 1 Fastening the seatbelt with the webbing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, especially when inserting the connector’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twisted. Be sure to fasten both tongue plates to the respective buckles.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 1-16 Seat, seatbelt and SRS airbags 3. After confirming that the webbing is not twisted, insert the connector (tongue) attached at the webbing end into the buckle on the right-hand side until a click is heard. Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-17 You should hold the webbing end and guide it back into the retractor while it is rolling up. Insert the tongue plate into the belt holder. 100289 To clean the seatbelts, use a mild soap and lukewarm water. Never bleach or dye the belts because this could seriously affect their strength.
A1910BE-A-G01SAAB.fm Page 18 Friday, September 9, 2005 1:49 PM 1-18 Seat, seatbelt and SRS airbags Seatbelt extender If the front seatbelts are not long enough to permit the tongue plate to engage with the seatbelt buckle, an optional seatbelt extender is available from your Saab dealer. When ordering an extender, only order one particularly designed for your vehicle. Several different types of extenders are available to match various varieties of front seatbelt designs.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-19 Front seatbelt pretensioners These occurrences are normal and not harmful. This smoke does not indicate a fire in the vehicle. Once the seatbelt pretensioner has been activated, the seatbelt retractor remains locked. Consequently, the seatbelt can not be pulled out and retracted and therefore must be replaced. NOTE 100121 The driver’s and front passenger’s seatbelts have a seatbelt pretensioner.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 1-20 Seat, seatbelt and SRS airbags When discarding front seatbelt retractor assemblies or scrapping the entire vehicle due to collision damage or for other reasons, consult your Saab dealer. ¢ System monitors 100291 A diagnostic system continually monitors the readiness of the seatbelt pretensioner while the vehicle is being driven. The seatbelt pretensioners share the control module with the SRS airbag system.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-21 ¢ System servicing When discarding a seatbelt retractor assembly or scrapping the entire vehicle damaged by a collision, consult your Saab dealer. Tampering with or disconnecting the system’s wiring could result in accidental activation of the seatbelt pretensioner and/or SRS airbag or could make the system inoperative, which may result in serious injury.
A1910BE-A-GSAAB.book Page 22 Tuesday, September 6, 2005 8:37 AM 1-22 Seat, seatbelt and SRS airbags Child restraint systems Children could be endangered in an accident if their child restraints are not properly secured in the vehicle. When installing the child restraint system, carefully follow the manufacturer’s instructions. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions.
A1910BE-A-GSAAB.book Page 23 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-23 Children should be properly restrained at all times. Never allow a child to stand up, or to kneel on any seat. Unrestrained children will be thrown forward during sudden stop or in an accident and can be injured seriously. Additionally, children standing up or kneeling on or in front of the front seat are exposed another serious danger.
A1910BE-A-GSAAB.book Page 24 Tuesday, September 6, 2005 8:37 AM 1-24 Seat, seatbelt and SRS airbags Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
A1910BE-A-GSAAB.book Page 25 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-25 ¢ Installing child restraint systems with A/ELR seatbelt Child restraint systems and seatbelts can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. Do not leave an unsecured child restraint system in your vehicle.
A1910BE-A-GSAAB.book Page 26 Tuesday, September 6, 2005 8:37 AM 1-26 Seat, seatbelt and SRS airbags ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully. q Installing forward facing child restraint 100506 100610 6. Push and pull the child restraint system forward and from side to side to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt. 7.
A1910BE-A-GSAAB.book Page 27 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-27 1 100137 4. Take up the slack in the lap belt. 5. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then, allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indicate the retractor functions as ALR. 100138 6.
A1910BE-A-GSAAB.book Page 28 Tuesday, September 6, 2005 8:37 AM 1-28 Seat, seatbelt and SRS airbags press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. NOTE When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully.
A1910BE-A-GSAAB.book Page 29 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-29 Never place the shoulder belt under the child’s arm or behind the child’s back. If an accident occurs, this can increase the risk or severity of injury to the child. The seatbelt should fit snugly in order to provide full restraint. Loose fitting belts are not as effective in preventing or reducing injury. Place the lap belt as low as possible on the child’s hips.
A1910BE-A-GSAAB.book Page 30 Tuesday, September 6, 2005 8:37 AM 1-30 Seat, seatbelt and SRS airbags es are sometimes referred to as the LATCH system (Lower Anchors and Tethers for CHildren). Your vehicle is equipped with four lower anchorages (bars) and three upper anchorages (tether anchorages) for accommodating such child restraint systems. 2 3 1 100614 You will find marks “ ” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars).
A1910BE-A-GSAAB.book Page 31 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-31 1. Use the “ ” marks to locate the two lower anchorages (bars) for the position where you want to install the child restraint system. 1 100616 100520 2. While following the instructions supplied by the child restraint system manufacturer, connect the lower hooks onto the lower anchorages located at “ ” marks on the bottom of the rear seatback.
A1910BE-A-GSAAB.book Page 32 Tuesday, September 6, 2005 8:37 AM 1-32 Seat, seatbelt and SRS airbags structions by the child restraint system manufacturer. q Anchorage location and anchorages for each of the two window-side seating positions on the rear wall of the cargo area. Since a top tether can provide additional stability by offering another connection between a child restraint system and the vehicle, we recommend that you use a top tether whenever one is required or available.
A1910BE-A-GSAAB.book Page 33 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-33 *SRS airbag (Supplemental Restraint System airbag) 100690 100297 2. (For both window-side seating positions) Remove the cap from the anchor fitting cover by prying it with a screwdriver. Window-side 3. Attach the child restraint top tether hook to the appropriate upper anchorage. 4. Tighten the top tether securely.
A1910BE-A-GSAAB.book Page 34 Tuesday, September 6, 2005 8:37 AM 1-34 Seat, seatbelt and SRS airbags and precautions concerning the seatbelt pretensioner, see the “Front seatbelt pretensioners” section in this chapter. To obtain maximum protection in the event of an accident, the driver and all passengers in the vehicle should always wear seatbelts when the vehicle is moving. The SRS airbag is designed only as a supplement to the primary protection provided by the seatbelt.
A1910BE-A-GSAAB.book Page 35 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-35 100082 Put children aged 12 and under in the rear seat properly restrained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or improperly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 37 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-37 ¢ Saab advanced frontal airbag system Your vehicle is equipped with a Saab advanced frontal airbag system that complies with the new advanced frontal airbag requirements in the amended Federal Motor Vehicle Safety Standard (FMVSS) No. 208.
A1910BE-A-GSAAB.book Page 38 Tuesday, September 6, 2005 8:37 AM 1-38 Seat, seatbelt and SRS airbags It is also important to wear your seatbelt to help avoid injuries that can result when the SRS airbag contacts an occupant not in proper position such as one thrown toward the front of the vehicle during preaccident braking. 100125 100155 Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child.
A1910BE-A-GSAAB.book Page 39 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-39 100157 Do not attach accessories to the windshield, or fit an extra-wide mirror over the rear view mirror. If the SRS airbag deploys, those objects could become projectiles that could seriously injure vehicle occupants. q Driver’s SRS frontal airbag The driver’s SRS frontal airbag uses a dual stage inflator.
A1910BE-A-GSAAB.book Page 40 Tuesday, September 6, 2005 8:37 AM 1-40 Seat, seatbelt and SRS airbags front passenger’s seat such as by kicking. Do not spill liquid on the front passenger’s seat. If liquid is spilled, wipe it off immediately. Do not disassemble the front passenger’s seat. Do not install any accessory (such as an audio amplifier) other than a genuine Saab accessory under the front passenger’s seat. Do not place anything (shoes, umbrella, etc.) under the front passenger’s seat.
A1910BE-A-GSAAB.book Page 41 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-41 q Conditions in which front passenger’s SRS frontal airbag is not activated The front passenger’s SRS frontal airbag will not be activated when any of the following conditions are met regarding the front passenger’s seat: The seat is empty. The seat is equipped with a rearward facing child restraint system and an infant is restrained with it. (See WARNING that follows.
A1910BE-A-GSAAB.book Page 42 Tuesday, September 6, 2005 8:37 AM 1-42 Seat, seatbelt and SRS airbags If still the ON indicator remains illuminated while the OFF indicator extinguishes, take the following actions. Ensure that no article is placed on the seat other than the child restraint system and the child occupant. Ensure that there is no article left in the seatback pocket.
A1910BE-A-GSAAB.book Page 43 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-43 correctly fasten the seatbelt, position his/ her legs out forward, and adjust the seat to the rearmost position. Turn the ignition switch to the “ON” position. If the OFF indicator remains illuminated while the ON indicator remains extinguished, take the following actions. Turn the ignition switch to the “OFF” position.
A1910BE-A-GSAAB.book Page 44 Tuesday, September 6, 2005 8:37 AM 1-44 Seat, seatbelt and SRS airbags q Operation A The SRS airbag can function only when the ignition switch is in the “ON” position. The Saab advanced frontal airbag system is designed to determine the activation or deactivation condition of the front passenger’s SRS frontal airbag depending on the total load on the front passenger’s seat monitored by the front passenger’s occupant detection system weight sensor.
A1910BE-A-GSAAB.book Page 45 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-45 case of the front passenger’s SRS frontal airbag. After deployment, the SRS airbag immediately starts to deflate so that the driver’s vision is not obstructed. The time required from detecting impact to the deflation of the SRS airbag after deployment is shorter than the blink of an eye.
A1910BE-A-GSAAB.book Page 46 Tuesday, September 6, 2005 8:37 AM 1-46 Seat, seatbelt and SRS airbags s Examples of the types of accidents in which it is possible that the driver’s/driver’s and front passenger’s SRS frontal airbag(s) will deploy. frontal airbags may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely impacted or knocked hard against an obstacle on the road such as a curb).
A1910BE-A-GSAAB.book Page 47 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-47 might not necessarily require deployment of driver’s/driver’s and front passenger’s SRS frontal airbag(s). If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset frontal impact, the driver’s/driver’s and front passenger’s SRS frontal airbag(s) may not deploy depending on the level of accident forces involved.
A1910BE-A-GSAAB.book Page 48 Tuesday, September 6, 2005 8:37 AM 1-48 Seat, seatbelt and SRS airbags ¢ SRS side airbag The SRS side airbag is stored in the door side of each front seat seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact collision, the SRS side airbag on the impacted side of the vehicle deploys between the occupant and the door panel and supplements the seatbelt by reducing the impact on the occupant’s chest and head.
A1910BE-A-GSAAB.book Page 49 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-49 1 100166 Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/her arms around the front seat seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously because his/her head or arms or other parts of the body are too close to the SRS side airbag.
A1910BE-A-GSAAB.book Page 50 Tuesday, September 6, 2005 8:37 AM 1-50 Seat, seatbelt and SRS airbags q Operation Do not put any kind of cover or clothes or other objects over either front seatback and do not attach labels or stickers to the front seat surface on or near the SRS side airbag. They could prevent proper deployment of the SRS side airbag, reducing protection available to the front seat’s occupant. The SRS side airbag is designed to function only when the ignition switch is in the “ON” position.
A1910BE-A-GSAAB.book Page 51 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-51 Do not touch the SRS side airbag system components around the front seat seatback with bare hands right after deployment. Doing so can cause burns because the components can be very hot as a result of deployment. The SRS side airbag is designed to deploy in the event of an accident involving a moderate to severe side impact collision. It is basically not designed to deploy in a lesser side impact.
A1910BE-A-GSAAB.book Page 52 Tuesday, September 6, 2005 8:37 AM 1-52 Seat, seatbelt and SRS airbags s Examples of the types of accidents in which the SRS side airbag is unlikely to deploy. 1) 2) 1 2 3) 4) 5) The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment. The vehicle strikes a telephone pole or similar object. The vehicle is involved in a side-on impact from a motorcycle.
A1910BE-A-GSAAB.book Page 53 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-53 s Examples of the types of accidents in which the SRS side airbag will basically not deploy. 1 The SRS side airbag is basically not designed to deploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are illustrated.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 55 Tuesday, September 6, 2005 8:37 AM Seat, seatbelt and SRS airbags 1-55 NOTE If you need service or repair in areas listed in the following, have an authorized Saab dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas.
A1910BE-A-GSAAB.book Page 56 Tuesday, September 6, 2005 8:37 AM 1-56 Seat, seatbelt and SRS airbags Installation of additional electrical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could interfere with proper operation of the SRS airbag system. Do not perform any of the following modifications. Such modifications can interfere with proper operation of the SRS airbag system.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Keys and doors Keys ..................................................................... 2-2 Key number ............................................................. 2-2 Immobilizer (Turbo models) .............................. 2-3 Security ID plate ..................................................... Security indicator light ........................................... Key replacement ....................................................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 2-2 Keys and doors Keys Keys and doors 1 1 2 3 4 2 3 4 5 Do not attach a large key holder or key case to either key. If it bangs against your knees while you are driving, it could turn the ignition switch from the ON position to the ACC or OFF position, thereby stopping the engine.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-3 Immobilizer (Turbo models) The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 2-4 Keys and doors equipped with an immobilizer system. It begins flashing (approximately once every three seconds) approximately 60 seconds after the ignition switch is turned from the “ON” position to the “ACC” or “LOCK” position or immediately after the key is pulled out. If the security indicator light does not flash, the immobilizer system may be faulty. If this occurs, we recommend that you contact your Saab dealer as soon as possible.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-5 ¢ Locking and unlocking from the inside 1 2 1 2 200805 1) Rotate the lock lever rearward. 2) Close the door. To lock the door from the outside without the key, rotate the lock lever rearward and then close the door. To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK” side) and then close the door.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 2-6 Keys and doors Power door locking switches ¢ Key lock-in prevention function 1 This function prevents the doors from being locked with the key still in the ignition switch. 2 200807 1) Lock 2) Unlock All doors and the rear liftgate can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors. To lock the doors, push the front side of the switch.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-7 Remote keyless entry system Two transmitters are provided for your vehicle. The remote keyless entry system has the following functions. Locking and unlocking the doors (and rear liftgate) without a key Sounding a panic alarm Arming and disarming the alarm system. See the next section “Alarm system” for detailed information. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 2-8 Keys and doors If any of the doors is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors are not properly closed. When you close the door, it will automatically lock. NOTE ¢ Illuminated entry ¢ Sounding a panic alarm The interior (dome) light and ignition switch light (for turbo models) will illuminate when the “ ” button is pressed.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-9 side of the power door locking switch, close the driver’s door once within 10 seconds after Step 4. 6. The turn signal lights flashes 3 times to indicate completion of the setting. To replace the battery: 0 2 1 NOTE If you do not close the driver’s door within 10 seconds after Step 4, a flash of the turn signal lights will signal timeout. If this happens, repeat the whole procedure from Step 1.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 2-10 Keys and doors Be careful not to damage the printed circuit board in the transmitter when replacing the battery. Programming transmitter codes into system: ¢ Replacing lost transmitters If you lose a transmitter or want to purchase additional transmitters (up to four can be programmed), you should re-program all of your transmitters for security reasons.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-11 NOTE 2 1 When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with part 3 of the procedure.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 2-12 Keys and doors number, push the unlock side of the lock switch within five seconds. again enter the transmitter code beginning with the leftmost digit. 11.Test every registered transmitter to confirm correct operation. NOTE NOTE q Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-13 Alarm system horn will stop sounding with a delay of up to 30 seconds. The alarm system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle. The starter motor is also interrupted to prevent starting the vehicle without a key. The alarm is triggered by: Opening a door or the rear liftgate.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 2-14 Keys and doors than two seconds). All doors and the rear liftgate will lock, an electric chirp will sound once, the turn signal lights will flash once, and the indicator lights will start flashing rapidly. After rapid flashing for 30 seconds (standby time), the indicator lights will then flash slowly (twice approximately every two seconds), indicating that the system has been armed for surveillance. 200885 : Press to Arm the system.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-15 The 30-second standby time can be eliminated if you prefer. Have it performed by your Saab dealer. The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period. If any of the following actions is done during the standby period, the system will not switch to the surveillance state.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 2-16 Keys and doors q Arming the system 1. Turn the ignition switch to the “ON” position. In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4 above or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk. 1 2 200817 200816 1) ON 2) LOCK 2.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-17 ings will recur each time the ignition switch is turned to the “ON” position. Rearming the alarm system cancels the flashing. Child safety locks Windows ¢ Power windows LO CK 200876 Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 2-18 Keys and doors q Driver’s side switches s Operating the driver’s window window will close as long as the switch is held. s Operating the passengers’ windows 3 1 2 3 4 5 1 2 200819 1) Lock switch 2) For driver’s window (with one-touch auto down feature) 3) For front passenger’s window 4) For rear left window 5) For rear right window All door windows can be controlled by the power window switch cluster at the driver side door.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-19 s Locking the passengers’ windows dow switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches. Rear liftgate 2 1 2 200821 1) Lock 2) Unlock To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ windows cannot be opened or closed.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 2-20 Keys and doors Do not attempt to shut the rear liftgate while holding the recessed grip. Also avoid closing the rear liftgate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand being caught and injured. 200887 To close the rear liftgate, lower it slowly and push down firmly until the latch engages. The rear liftgate can be lowered easily if you pull down on the recessed grip.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM Keys and doors 2-21 Moonroof 3 The moonroof has both tilting and sliding functions. Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause damage to the moonroof. The moonroof operates only when the ignition switch is in the “ON” position.
A1910BE-A-GSAAB.book Page 22 Tuesday, September 6, 2005 8:37 AM 2-22 Keys and doors Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof. Do not sit on the edge of the open moonroof. Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Instruments and controls Ignition switch .................................................... 3-3 LOCK ....................................................................... ACC .......................................................................... ON ............................................................................ START ...................................................................... Key reminder chime ................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM Instruments and controls Mirrors ................................................................. 3-24 Inside mirror ........................................................... Outside mirrors ....................................................... 3-24 3-25 Tilt steering wheel .............................................. Horn .....................................................................
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-3 Ignition switch Instruments and controls or to a large bunch of other keys, centrifugal force may act on it as the vehicle moves, resulting in unwanted turning of the ignition switch. Also, if a large keyholder is attached to the key, your knees or hands may accidentally touch it in a way that turns the ignition switch. 3 ¢ LOCK The ignition switch has four positions: LOCK, ACC, ON and START.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 3-4 Instruments and controls “LOCK” only when the key is pushed in while turning it. Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-5 ¢ Key reminder chime dealer immediately to have the key interlock system repaired. The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ignition switch. 3 ¢ Ignition switch light 3 For easy access to the ignition switch in the dark, the ignition switch light comes on when driver’s door is opened.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 3-6 Instruments and controls Hazard warning flasher Meters and gauges trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position. NOTE q Odometer The odometer shows the total distance that the vehicle has been driven. Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear polarized glasses.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-7 trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds. To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result. NOTE If the connection between the instrument cluster and battery is broken for any reason such as vehicle maintenance or fuse replacement, the data recorded on the trip meter will be lost.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 3-8 Instruments and controls ¢ Temperature gauge If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9. 1 ¢ Outside temperature indicator 300629 1 1) Normal operating range The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-9 Warning and indicator lights Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits checking the operation of the bulbs. Apply the parking brake and turn the ignition switch to the “ON” position.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 3-10 Instruments and controls ¢ SRS airbag system warning light When the ignition switch is turned to the “ON” position, the SRS airbag system warning light will come on for approximately six seconds and go out. This shows the SRS airbag and SRS side airbag 3 and seatbelt pretensioners are in normal operation.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-11 ¢ CHECK ENGINE warning light/Malfunction indicator lamp If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your Saab dealer as soon as possible. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 3-12 Instruments and controls ¢ ABS warning light Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage. ¢ AT OIL TEMPerature warning light (AT vehicles) (U.S.) (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately two seconds. This is an indication that the ABS system is working properly.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-13 When the battery becomes fully charged, the light will go out. ¢ Brake system warning light (U.S.) (Canada) Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a Saab dealer immediately. If at all in doubt about whether the brakes are operating properly, do not drive the vehicle.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 3-14 Instruments and controls Always make sure this light is out before you start to drive. ¢ All-Wheel Drive warning light (AWD AT vehicles) ¢ Selector lever position indicator (AT vehicles) This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. P R N Continuing to drive with the AWD warning light flashing can damage the powertrain.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-15 to the “ACC” or “LOCK” position, and then turn it again to the “ON” position. Clock Light control switch The light switch operates only when the ignition switch is in the “ON” position. ¢ Cruise control set indicator light The cruise control set indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approximately three seconds.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 3-16 Instruments and controls ¢ Headlights ¢ High/low beam change (dimmer) 300127 To turn on the headlights, turn the knob on the end of the turn signal lever. first position Parking lights, instrument panel illumination, tail lights, front side marker lights and license plate light are on. second position Headlights, parking lights, instrument panel illumination, tail lights, and license plate light are on.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-17 ¢ Daytime running light system q Cars with HID headlights The low beam headlights, tail lights, parking lights, and licence plate lights will automatically come on when the engine has started, under the following conditions: The parking brake is fully released. The light switch is in the “OFF” or “ ” position. The automatic transmission selector lever is set at other than the “P” position.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 3-18 Instruments and controls turn automatically to the neutral position when you release it. Illumination brightness control 300131 When the headlight switch is in the “ ” or “ ” position, you can adjust brightness of the instrument panel illumination for better visibility. To brighten, turn the control dial upward. To darken, turn the control dial downward.
A1910BE-A-G03SAAB.fm Page 19 Tuesday, September 6, 2005 8:53 AM Instruments and controls 3-19 lightly loaded vehicle, set the adjuster to “0”. Front fog light button 3 Parking light switch 3 300134 The parking light switch operates regardless of the ignition switch position. By pushing the front end of this switch, following lights will come on. – Parking lights – Front side marker lights – Tail lights – License plate lights To turn off, push the rear end of the parking light switch.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 3-20 Instruments and controls Wiper and washer In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view. Do not operate the washer continuously for more than ten seconds, or when the washer fluid tank is empty. This may cause overheating of the washer motor.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-21 results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water.
A1910BE-A-GSAAB.book Page 22 Tuesday, September 6, 2005 8:37 AM 3-22 Instruments and controls q Mist (for a single wipe) To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button. ¢ Rear window wiper and washer switch 300139 ON For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever.
A1910BE-A-GSAAB.book Page 23 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-23 Rear window defogger button NOTE If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the rear window defogger is operating. Turn on the rear window defogger if the wiper is frozen to the glass. The rear window defogger operates only when the ignition switch is in the “ON” position. The rear window defogger button is located on the climate control panel.
A1910BE-A-GSAAB.book Page 24 Tuesday, September 6, 2005 8:37 AM 3-24 Instruments and controls Windshield wiper deicer 3 complete when you restart your vehicle, you have to push the button to turn the deicer on again. NOTE If your vehicle is equipped with the outside mirror defogger, the outside mirror defogger operates while the rear window defogger is operating. 300143 Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving.
A1910BE-A-GSAAB.book Page 25 Tuesday, September 6, 2005 8:37 AM Instruments and controls 3-25 ¢ Outside mirrors q Outside mirror defogger 3 q Remote control mirror switch 1 3 2 300625 300146 q Convex mirror (passenger side) Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes.
A1910BE-A-GSAAB.book Page 26 Tuesday, September 6, 2005 8:37 AM 3-26 Instruments and controls The outside mirror defogger shares the button with rear window defogger. The outside mirror defogger operates only when the ignition switch is in the “ON” position. To turn on the outside mirror defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the outside mirror defogger is operating.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Climate control 1 Ventilation ........................................................... 4-2 Air flow selection .................................................... Center and side vents ............................................ Manual climate control system 3 ..................... Control panel .......................................................... Heater operation .....................................................
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Climate control 4-3 ¢ Center and side vents Manual climate control system 3 q Side vents q Center vents ¢ Control panel 6 1 2 5 3 4 2 4 400597 400376 Move the tab up and down or right and left to adjust the air flow direction. 1) Open 2) Close Move the knob in any direction you prefer to adjust the air flow direction. To open the vent, turn the knob counterclockwise. To close the vent, turn the knob clockwise.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 4-4 Climate control q Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. q Air flow control dial This dial has the following five positions: : Air flows through the instrument panel outlets. : Air flows through the instrument panel outlets and the foot outlets.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Climate control 4-5 ¢ Heater operation q Defrosting or defogging the windshield of the position of the air conditioner button to defog the windshield quickly. However, the air conditioner indicator light does not come on at this time. NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corresponding knob clockwise. q Heating and defrosting 4.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 4-6 Climate control NOTE foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection lever to the “ ” position. 2. Set the air flow control dial to the “ ” position. 3. Set the temperature control dial to the desired temperature level. 4. Set the fan speed control dial to the desired speed.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Climate control 4-7 ¢ Air conditioner operation Automatic climate control system 3 q Defrosting or defogging q Cooling or dehumidifying 400368 400373 For cooling and dehumidification of the passenger compartment, performing the following steps will allow air to flow through the instrument panel outlets: 1. Set the air inlet selection lever to the “ ” position. 2. Set the air flow control dial to the “ ” position. 3.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 4-8 Climate control turns on the air conditioner compressor automatically and the “A/C” indicator light on the control panel comes on. ¢ Control panel 1 2 3 then set the other dials and buttons as described in the following. The system’s functions will then switch to AUTO mode and be controlled automatically.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Climate control 4-9 AUTO position and the air flow control dial in the “ ”, “ ”, or “ ” position, the fan does not operate during engine warmup until the engine coolant temperature exceeds approx. 122°F (50°C).
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 4-10 Climate control OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will go off. AUTO: When the air inlet selection button is pressed for at least 1 second, the indicator flashes twice.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Climate control 4-11 – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors. Operating tips for heater and air conditioner The sensors are located as follows: – Solar sensor: beside windshield defroster grille – Interior air temperature sensor: beside the fan speed control dial – Outside temperature sensor: behind front grille.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 4-12 Climate control any problem with the air conditioning system. ¢ Air conditioner compressor shut-off when engine is heavily loaded To improve acceleration and gas mileage, the air conditioner compressor is designed to temporarily shut off during air conditioner operation whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Climate control 4-13 4 2 1 400605 2. Unhook the hooks of the air filter cover and remove the cover. 400607 1) Air filter element 2) Arrow mark 400608 5. Reinstall the air filter cover. 4. Replace the air filter element with new one. The arrow mark on the filter must point down. 1 400604 400606 1) Air filter element 3. Draw out the air filter element. 6. Connect the connector, and reinstall the glove box. 7. Close the glove box.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 4-14 Climate control Contact your dealer if the following occurs, even if it is not yet time to change the filter: Reduction of the air flow through the vents. Windshield gets easily fogged or misted. NOTE The filter can influence the air conditioning, heating and defroster performance if not properly maintained.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Audio Antenna system .................................................. 5-2 Printed antenna ....................................................... FM reception ........................................................... 5-2 5-2 Installation of accessories ................................ Audio Systems ................................................... 5-2 5-3 AM/FM/Single-CD Audio System ...........................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 5-2 Audio Antenna system Audio ¢ Printed antenna Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window. 500250 The antenna is printed on the inner surface of the rear window glass.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Audio 5-3 Audio Systems Your Saab may be equipped with one of the following audio sets. See the pages indicated in this section for operating details.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 5-4 Audio AM/FM/Single-CD Audio System 3 The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Audio 5-5 modes in the following sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Audio 5-7 q FM/AM selection button (FM/AM) Push the “FM/AM” button (4) when the radio is off to turn on the radio. Push the “FM/AM” button when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order: FM1 FM2 AM The display indicates which one is currently selected. q Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 5-8 Audio ¢ Compact disc player operation (7) (8) (7) Eject button (8) Disc slot (9) DISC button (10) Repeat/Random button (11) Track selection buttons (9) q To play back a compact disc (11) (10) 500024 s When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Audio 5-9 NOTE After the last song finishes, playback will automatically return to track 1 (the first song on the disc). q To select a song from its beginning s Forward direction Briefly press the “ ” side of the track selection button (11) to skip to the beginning of the next track. Each time this side of the button is pressed, the indicated track number will increase.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 5-10 Audio ¢ CD changer control (if optional in-dash CD changer is connected) An optional CD changer can be connected to this audio unit. Consult the instructions that accompany the CD changer for operating the CD changer itself (e.g., how to load or unload CDs). See your Saab dealer for more information.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Audio 5-11 only by pressing the corresponding number on one of the “Disc select” buttons (15). If you are to listen to the 5th disc in the CD changer, press the “5” button of the “Disc select” buttons (15). All other discs in the CD changer can also be selected in a similar way. NOTE No disc change takes place if the button corresponding to the storage tray in which no disc is loaded is pressed.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 5-12 Audio Premium AM/FM/6-CD Audio System 3 The radio will operate only when the ignition switch is in the “ACC” or “ON” position.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 5-14 Audio s Tone control The volume control dial (8) normally function as volume control. The dial becomes a control for Bass, Midrange or Treble when you select the appropriate tone control mode. Choose desired level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 seconds.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Audio 5-15 s Seek tuning Turn the tuning knob (6) and hold it for more than a half second. Seek tuning will operate and stop automatically on the next station. Continue this operation until you find the desired station. q Automatic tuning (SCAN) Press the “SCAN” button (5) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 5-16 Audio ¢ Built in CD changer operation (9) (10) (11) (12) (9) LOAD button (10) Disc slot (11) Repeat button (12) Random button (13) SCAN button (14) CD button (15) Eject button (16) Fast-forwarding/Fast-reversing and track UP/DOWN knob (17) Disc select button (13) (14) (15) NOTE Make sure to always insert a disc with the label side up.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Audio 5-17 during the period. The disc will be then automatically drawn in, and the player will begin to play back the first track of the disc. To insert more discs in succession, repeat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 5-18 Audio q Selecting a desired track (TRACK) s Fast-forwarding Turn the “TRACK” knob (16) clockwise and hold it continuously to fast-forward the disc. Release the knob to stop fast-forwarding. s Fast-reversing Turn the “TRACK” knob (16) counterclockwise and hold it continuously to fastreverse the disc. Release the knob to stop fast-reversing.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Audio 5-19 move the disc that has been ejected, the “All disc ejection mode” will be canceled. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. Precautions to observe when handling a compact disc Use only compact discs (CDs) that have the mark shown in the following illustration.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 5-20 Audio form inside the CD player, preventing normal operation. If this happens, eject the CD and wait for the player to dry out. Skipping may occur when the CD player is subjected to severe vibration (for example, when the vehicle is driven on a rough surface). To remove a disc from the case, press the center of the case and hold both edges of the disc.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Interior equipment Interior light ........................................................ 6-2 Dome light ............................................................... Cargo area light ...................................................... 6-2 6-2 Map light 3 .......................................................... Sun visors ........................................................... 6-2 6-3 Vanity mirror ............................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 6-2 Interior equipment Interior light Interior equipment When leaving your vehicle, make sure the light goes out to avoid battery discharge. ¢ Dome light the “Remote keyless entry system” section in chapter 2 for detailed information. OFF: The light stays off. Map light 3 ¢ Cargo area light OFF ON DOOR DOOR OFF 600524 Vehicle with moonroof 400333 600078 The dome light switch has three positions: ON: The light stays on continuously.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Interior equipment 6-3 To turn on the map light, push the switch. To turn it off, push the switch again. ¢ Vanity mirror Sun visors When leaving the vehicle, make sure the light is turned off to avoid battery discharge. 600219 600218 To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways. To use the vanity mirror, swing down the sun visor and open the vanity mirror cover.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 6-4 Interior equipment Storage compartments To lock the glove box, insert the key and turn it clockwise. Always keep the storage compartment closed while driving to reduce the risk of injury in the event of sudden stops or an accident. Do not store spray cans, containers with flammable or corrosive liquids or any other dangerous items in the storage compartment.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Interior equipment 6-5 Cup holder ¢ Front passenger’s cup holder Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, carpets or audio equipment. Cigarette lighter socket 6 600221 600231 A dual cup holder is built in the center console, beside the parking brake lever.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 6-6 Interior equipment ¢ Use with a cigarette lighter The electrical power outlet located on the lower part of the instrument panel is originally designed to use a genuine Saab cigarette lighter plug. Do not use non-genuine cigarette lighter plugs in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Interior equipment 6-7 If the plug on your electric appliance is either too loose or too tight for the socket, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly. Use of an electric appliance in the socket for a long period of time while the engine is not running can cause battery discharge.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 6-8 Interior equipment Floor mat 3 Coat hook 600481 600513 A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release. The floor mat is secured using the built-in grommet, by placing the grommet over the pin and pushing downward. 600224 Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retaining pin.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Interior equipment 6-9 Cargo area cover The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo. ¢ Using the cover Do not place anything on the extended cover. Putting excessive weight on the extended cover can break it and an object on the cover could tumble forward in the event of a sudden stop or collision.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 6-10 Interior equipment The cargo area cover can be stowed under the cargo floor. Cargo tie-down hooks ¢ To install the cover housing 1. Pull either sleeve on the end of the cover housing to shorten the cover’s length. 600229 600228 2. Insert the projections located on the both ends of the sleeve into the recesses of the retainers. The cargo area is equipped with four tiedown hooks so that cargo can be secured with a cargo net or ropes.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Starting and operating Fuel ...................................................................... 7-2 Fuel requirements .................................................. Fuel filler lid and cap .............................................. 7-2 7-3 State emission testing (U.S. only)/Canadian Provincial Emission Testing .......................... Preparing to drive .............................................. Starting the engine ........
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 7-2 Starting and operating Fuel Starting and operating Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage. ¢ Fuel requirements q 2.5-liter non-turbo models The 2.5-liter non-turbo engine is designed to operate using unleaded gasoline with an octane rating of 87 AKI or higher. q 2.5-liter turbo models 3 The 2.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-3 helps keep your engine in tune and your emission control system working properly, and is a way of doing your part for cleaner air. If you continuously use a high quality fuel with the proper detergent and other additives, you should never need to add any fuel system cleaning agents to your fuel tank. Many gasolines are now blended with materials called oxygenates.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 7-4 Starting and operating When opening the cap, do not remove the cap quickly. Fuel may be under pressure and spray out of the fuel filler neck especially in hot weather, which may cause injury. 2 1 700330 1) Open 2) Close 2. Remove the fuel filler cap by turning it slowly counterclockwise. 3. Stop filling the tank after the fuel filler pump automatically stops. Do not add any more fuel. 4.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-5 State emission testing (U.S. only)/Canadian Provincial Emission Testing At state inspection time, remember to tell your inspection or service station in advance not to place your Saab AWD vehicle on a two-wheel dynamometer. Otherwise, serious transmission damage will result.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 7-6 Starting and operating A vehicle fails the OBD inspection if the “CHECK ENGINE” warning light/MIL is not properly operating or there is one or more diagnostic trouble codes stored in vehicle’s computer with the “CHECK ENGINE” warning light/MIL illuminated. A state emission inspection may reject (not pass or fail) a vehicle if the number of OBD system readiness monitors “Not Ready” is greater than one.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-7 If the engine does not start, try the following. 1) Turn the ignition switch to the “OFF” position and wait for at least 10 seconds. After checking that the parking brake is firmly set, turn the ignition switch to the “START” position while depressing the accelerator pedal slightly (about a quarter of the full stroke). Release the accelerator pedal as soon as the engine starts.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 7-8 Starting and operating “N” position and that the parking brake is applied. Stopping the engine NOTE The ignition switch should be turned off only when the vehicle is stopped and the engine is idling. If you restart the engine while the vehicle is moving, shift the selector lever into the “N” position. Do not attempt to place the selector lever of a moving vehicle into the “P” position.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-9 Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased. Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmission to try shifting into reverse when the vehicle is moving.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 7-10 Starting and operating grade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components. Automatic transmission When it is necessary to reduce vehicle speed due to slow traffic, turning corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-11 When parking the vehicle, first securely apply the parking brake and then place the selector lever in the “P” position. Avoid parking for a long time with the selector lever in any other position as doing so could result in a dead battery. sure safe starting of the vehicle.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 7-12 Starting and operating NOTE If you stop the engine with the selector lever in the “N” position, move the selector lever to the “P” position immediately. Otherwise, you may find that the selector lever soon cannot be moved to the “P” position. If you find that the selector lever cannot be moved from the “N” position to the “P” position, turn the ignition switch to the “ON” position and try again.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-13 standstill on slippery road surfaces such as mud or snow. It will ensure greater traction. q 1 (First) This position is for driving up or down very steep grades, or driving through mud or sand, or on slippery surfaces. In this position, the transmission holds in the 1st gear. q Maximum speeds The following tables show the maximum speeds that are possible with each different gear.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 7-14 Starting and operating 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine. Limited slip differential (LSD) 3 Take your vehicle to the nearest Saab dealer immediately to have the system repaired.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-15 Power steering Braking The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take much more effort.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 7-16 Starting and operating ¢ Disc brake pad wear warning indicators ABS (Anti-lock Brake System) The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road surfaces. This helps prevent the loss of steering control and directional stability caused by wheel lock-up. When the ABS system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-17 the ABS system being carried out and does not indicate any abnormal condition. ¢ ABS warning light 700359 The ABS warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately two seconds. This is an indication that the ABS system is working properly.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 7-18 Starting and operating Electronic Brake Force Distribution (EBD) system The EBD system maximizes the effectiveness of the brakes by allowing the rear brakes to supply a greater proportion of the braking force. It functions by adjusting the distribution of braking force to the rear wheels in accordance with the vehicle’s loading condition and speed.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-19 Parking your vehicle Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a Saab dealer immediately. If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle towed to the nearest Saab dealer for repair.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 7-20 Starting and operating 700366 When parking on a hill, always turn the steering wheel. When the vehicle is headed up the hill, the front wheels should be turned away from the curb. 700367 When facing downhill, the front wheels should be turned into the curb. Never leave unattended children or pets in the vehicle. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-21 Cruise control ¢ To set cruise control vehicle reaches the desired speed. Cruise control enables you to maintain a constant vehicle speed without holding your foot on the accelerator pedal and it is operative when the vehicle speed is 25 mph (40 km/h) or more. Make sure the main switch is turned “OFF” when the cruise control is not in use to avoid unintentionally setting the cruise control.
A1910BE-A-GSAAB.book Page 22 Tuesday, September 6, 2005 8:37 AM 7-22 Starting and operating The vehicle will maintain the desired speed. Vehicle speed can be temporarily increased while driving with the cruise control activated. Simply depress the accelerator pedal to accelerate the vehicle. When the accelerator pedal is released, the vehicle will return to and maintain the previous cruising speed.
A1910BE-A-GSAAB.book Page 23 Tuesday, September 6, 2005 8:37 AM Starting and operating 7-23 q To increase the speed (by accelerator pedal) 1. Depress the accelerator pedal to accelerate the vehicle to the desired speed. 2. Push the control lever downward in the “SET/COAST” direction once. Now the desired speed is set and the vehicle will keep running at that speed without depressing the accelerator pedal.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Driving tips 3 Asterisk means: equipment not fitted in all cars (can depend on model variant, engine variant, market specification, options or accessories). New vehicle break-in driving – the first 1,000 miles (1,600 km) .............................................. Fuel economy hints ............................................ Engine exhaust gas (Carbon monoxide) .......... Catalytic converter .............................................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 8-2 Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 km) Fuel economy hints The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): Do not race the engine. And do not allow engine speed to exceed 4,000 rpm except in an emergency.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Driving tips 8-3 If at any time you suspect that exhaust fumes are entering the vehicle, have the problem checked and corrected as soon as possible. If you must drive under these conditions, drive only with all windows fully open. Keep the trunk lid or rear liftgate closed while driving to prevent exhaust gas from entering the vehicle. Catalytic converter The catalytic converter is installed in the exhaust system.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 8-4 Driving tips Keep everyone and flammable materials away from the exhaust pipe while the engine is running. The exhaust gas is very hot. Periodic inspections Driving in foreign countries To keep your vehicle in the best condition at all times, always have the recommended maintenance services listed in the maintenance schedule in the “Saab Warranty and Service Record Booklet” performed at the specified time or mileage intervals.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Driving tips 8-5 Driving tips for AWD vehicles 800004 All-Wheel Drive distributes the engine power to all four wheels. AWD vehicles provide better traction when driving on slippery, wet or snow-covered roads and when moving out of mud, dirt and sand. By shifting power between the front and rear wheels, AWD can also provide added traction during acceleration and added engine braking force during deceleration.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 8-6 Driving tips Off road driving Always maintain a safe driving speed according to the road and weather conditions in order to avoid having an accident on a sharp turn, during sudden braking or under other similar conditions. Always use the utmost care in driving – overconfidence because you are driving an All-Wheel Drive vehicle could easily lead to a serious accident.
A1910BE-A-G08SAAB.fm Page 7 Tuesday, September 6, 2005 8:55 AM Driving tips 8-7 Keep the door locks from freezing by squirting them with deicer or glycerin. Forcing a frozen door open may damage or separate the rubber weather strips around the door. If the door is frozen, use hot water to melt the ice, and afterwards thoroughly wipe the water away. Use a windshield washer fluid that contains an antifreeze solution.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 8-8 Driving tips your vehicle and the vehicle ahead of you to avoid the need for sudden braking. To supplement the foot brake, use the engine brake effectively to control the vehicle speed. (Shift into a lower gear when necessary.) Avoid shifting down abruptly. Such behavior can cause the wheels to lock, possibly leading to loss of vehicle control.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Driving tips 8-9 ¢ Snow tires When replacing original tires with winter (snow) tires, make sure you use only the same size, construction and load range as the original tires listed on the tire label. Using other sizes and construction may affect speedometer/odometer calibration and clearance between the body and tires. It also may be dangerous and lead to loss of vehicle control.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 8-10 Driving tips repeatedly. Do not race the engine. For the best possible traction, avoid spinning the wheels when trying to free the vehicle. When the road surface is extremely slippery, you can obtain better traction by starting the vehicle with the transmission in 2nd than 1st (both for MT and AT). Refer to the “Automatic transmission” section in chapter 7 for information on holding the transmission in 2nd position.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Driving tips 8-11 ¢ GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating) Do not carry spray cans, containers with flammable or corrosive liquids or any other dangerous items inside the vehicle. NOTE For better fuel economy, do not carry unneeded cargo. ¢ Vehicle capacity weight D00120 The load capacity of your vehicle is determined by weight, not by available cargo space.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 8-12 Driving tips In addition, the total weight applied to each axle (GAW) must never exceed the GAWR. The front and rear GAWs can be adjusted by relocating luggage inside the vehicle. Even if the total weight of your luggage is lower than the vehicle capacity weight, either front or rear GAW may exceed the GAWR, depending on the distribution of the luggage. When possible, the load should be evenly distributed throughout the vehicle.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Driving tips 8-13 Trailer towing Your vehicle is designed and intended to be used primarily as a passenger-carrying vehicle. Towing a trailer puts additional loads on your vehicle’s engine, drivetrain, brakes, tires and suspension and has an adverse effect on fuel economy. If you do decide to tow a trailer, your safety and satisfaction depend upon proper use of correct equipment and cautious operation of your vehicle.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 8-14 Driving tips Model MT models AT models Conditions Maximum total trailer weight When towing a trailer without brakes. 1,000 lbs (453 kg) When towing a trailer with brakes. 2,000 lbs (906 kg) When towing a trailer without brakes. 1,000 lbs (453 kg) When towing a trailer with brakes.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Driving tips 8-15 q Tongue load q Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR) 800261 800274 Gross Axle Weight The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehicle. The front and rear GAWR are also shown on the certification plate.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 8-16 Driving tips 1 2 F 60% 40% 800270 1) Jack 2) Bathroom scale The tongue load can be weighed with a bathroom scale as shown in the following illustration. When weighing the tongue load, be sure to position the towing coupler at the height at which it would be during actual towing, using a jack as shown. 50% 50% 800216 F: Front of vehicle The tongue load can be adjusted by proper distribution of the load in the trailer.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Driving tips 8-17 Never drill the frame or under-body of your vehicle to install a commercial trailer hitch. If you do, dangerous exhaust gas, water or mud may enter the passenger compartment through the drilled hole. Exhaust gas contains carbon monoxide, a colorless and odorless gas which is dangerous, or even lethal, if inhaled.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 8-18 Driving tips count; however, be careful not to let them drag on the ground. For more information about the safety chain connection, refer to the instructions for your hitch and trailer. Always use safety chains between your vehicle and the trailer. Towing a trailer without safety chains could create a traffic safety hazard if the trailer separates from the hitch due to coupling damage or hitch ball damage.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Driving tips 8-19 When towing a trailer, steering, stability, stopping distance and braking performance will be different from normal operation. For safety’s sake, you should employ extra caution when towing a trailer and you should never speed. You should also keep the following tips in mind: q Before starting out on a trip Check that the vehicle and vehicle-tohitch mounting are in good condition.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 8-20 Driving tips steering wheel with one hand and turn it to the left for a left turn, and turn it to the right for a right turn. If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the nearest Saab dealer.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM In case of emergency If you park your vehicle in case of an emergency ....................................................... Temporary spare tire .......................................... Flat tires .............................................................. 9-2 9-2 9-4 Changing a flat tire ................................................. 9-4 Jump starting ......................................................
A1910BE-A-G09SAAB.fm Page 2 Tuesday, September 6, 2005 8:56 AM 9-2 In case of emergency If you park your vehicle in case of an emergency In case of emergency NOTE When the hazard warning flasher is on, the turn signals do not work. Temporary spare tire The temporary spare tire is smaller and lighter than a conventional tire and is designed for emergency use only.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-3 2 1 Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle and may lead to an accident.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 9-4 In case of emergency Flat tires If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place. ¢ Changing a flat tire Do not jack up the vehicle on an incline or a loose road surface. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-5 900047 Open the lid and hang the hook provided on the under side of the lid on the rear edge of the roof to keep the lid open. Turn the attaching bolt counterclockwise, then take spare tire out. If the spare tire provided in your vehicle is a temporary spare tire, carefully read the section “Temporary spare tire” in this chapter and strictly follow the instructions.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 9-6 In case of emergency Turn the jackscrew by hand until the jack head engages firmly into the jack-up point. 900281 6. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts. 900009 900055 8. Insert the jack handle into the jackscrew, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary. 9. Remove the wheel nuts and the flat tire. 900073 900053 7.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-7 Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident. the top of the wheel nut wrench. Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have the wheel nut torque checked at the nearest automotive service facility. 12.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 9-8 In case of emergency Jump starting Battery fluid is SULFURIC ACID. Do not let it come in contact with the hooks, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and obtain immediate medical help.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-9 1) Connect one jumper cable to the positive (+) terminal on the discharged battery. 2) Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. 3) Connect one end of the other cable to the negative (–) terminal of the booster battery. 4) Connect the other end of the cable to the engine lifting bracket.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 9-10 In case of emergency Engine overheating Never attempt to remove the radiator cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously. If the engine overheats, safely pull off the road and stop the vehicle in a safe place.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-11 ¢ Towing and tie-down hooks Rear towing hook: The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow). Front towing hook: 1. Take out the towing hook, screwdriver and wheel nut wrench from the on board tool bag. 900284 4. Tighten the towing hook securely using the wheel nut wrench.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 9-12 In case of emergency Tie-down hooks: Use only the specified towing hook and tie-down hook. Never use suspension parts or other parts of the body for towing or tiedown purposes. Never use the tie-down hook on the underside of the vehicle closest to the muffler for towing purposes. 1 1 ¢ Using a flat-bed truck or “1st” for manual transmission vehicles. 2. Pull up the parking brake lever firmly. 3.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-13 1. Check the transmission and differential oil levels and add oil to bring it to the upper level if necessary. 2. Release the parking brake and put the transmission in neutral. 3. The ignition switch should be in the “ACC” position while the vehicle is being towed. 4. Take up slack in the towline slowly to prevent damage to the vehicle.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 9-14 In case of emergency Moonroof – if the moonroof cannot be closed If the moonroof cannot be closed with the moonroof switch, you can close the moonroof manually. 1. Take out the hex-headed wrench from the glove compartment and screwdriver from the tool bag. 900069 900067 4. Insert the wrench in the end of the motor shaft. To lower the moonroof, turn the wrench clockwise. To close the moonroof, turn the wrench counterclockwise. 3.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM In case of emergency 9-15 ¢ Jack and jack handle Maintenance tools 1 3 2 900279 900280 900291 Your vehicle is equipped with the following maintenance tools: Screwdriver Towing hook (eye bolt) Wheel nut wrench *Hex-headed wrench (vehicles with moonroof) *: The hex-headed wrench is stored in the glove box. The jack is stored on the left side of the cargo area.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Appearance care Exterior care ....................................................... 10-2 Washing ................................................................... Waxing and polishing ............................................. Cleaning aluminum wheels .................................... 10-2 10-3 10-3 Corrosion protection .......................................... 10-4 Most common causes of corrosion ......................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 10-2 Appearance care Exterior care Appearance care ¢ Washing When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do not wash the engine compartment and area adjacent to it.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Appearance care 10-3 If a stain will not come out easily, wash by hand. Some warm water washers are of the high temperature, high pressure type, and they can damage or deform the resin parts such as mouldings, or cause water to leak into the vehicle. ¢ Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and apply them according to the manufacturer’s instructions.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 10-4 Appearance care Corrosion protection Your Saab has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable operation. ¢ Most common causes of corrosion The most common causes of corrosion are: 1. The accumulation of moisture retaining dirt and debris in body panel sections, cavities, and other areas. 2.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Appearance care 10-5 Cleaning the interior Use a soft, damp cloth to clean the climate control panel, audio equipment, instrument panel, center console, combination meter panel, and switches. (Do not use organic solvents.) ¢ Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft blush then vacuum it.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Maintenance and service Maintenance schedule ....................................... Maintenance precautions .................................. 11-3 11-3 Automatic transmission fluid ............................ 11-20 11-4 Front differential gear oil (AT vehicles) ............ 11-22 Before checking or servicing in the engine compartment ........................................................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM Maintenance and service Tires and wheels ................................................ 11-30 Types of tires .......................................................... Tire inspection ........................................................ Tire pressures and wear ........................................ Wheel balance ........................................................ Wear indicators ....................................................
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-3 Maintenance schedule Maintenance and service The scheduled maintenance items required to be serviced at regular intervals are shown in the “Saab Warranty and Service Record Booklet”. For details of your maintenance schedule, read the separate “Saab Warranty and Service Record Booklet”.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 11-4 Maintenance and service Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get in your eyes, thoroughly wash them out with clean water. Do not tamper with the wiring of the SRS airbag system or seatbelt pretensioner system, or attempt to take its connectors apart, as that may activate the system or it can render it inoperative.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-5 from its retainer and put the end of the hood prop into the slot in the hood. To close the hood: 1. Lift the hood slightly and remove the hood prop from the slot in the hood and return the prop to its retainer. 2. Lower the hood until it approaches approximately 12 in (30 cm) from the closed position and let it drop. B00479 3.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 11-8 Maintenance and service Engine oil ¢ Checking the oil level 1 Check the engine oil level at each fuel stop. 1. Park the vehicle on a level surface and stop the engine. 2 3 B00418 1) Notch 2) Upper level 3) Lower level B00467 2. Pull out the dipstick, wipe it clean, and insert it again. 3. Be sure the dipstick is correctly inserted until it stops with the graphic symbol “ ” on its top appearing as shown in the illustration. 4.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-9 Do not touch the exhaust manifold or turbocharger. These get very hot when the engine has been running. B00450 Non-turbo models B00449 Turbo models 4. Drain out the engine oil by removing the drain plug while the engine is still warm. The used oil should be drained into an appropriate container and disposed of properly.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 11-10 Maintenance and service 8. Before installing a new genuine Saab oil filter, apply a thin coat of engine oil to the seal. 9. Clean the rubber seal seating area of the bottom of engine and install the genuine Saab oil filter by hand turning. Be careful not to twist or damage the seal. 10.Tighten the oil filter by the amount indicated in the following table after the seal makes contact with the bottom of engine.
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-11 ¢ Recommended grade and viscosity Oil grade: -30 -20 -10 0 ILSAC GF-4, which can be identified with the ILSAC certification mark (Starburst mark) or API classification SM with the words “ENERGY CONSERVING” These recommended oil grades can be identified by looking for either or both of the following marks displayed on the oil container.
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 11-12 Maintenance and service eas with very high temperatures, or used for heavy-duty applications such as towing a trailer, use of oil with the following grade and viscosities is recommended. API classification SM (or SL): SAE viscosity no.: 30, 40, 10W-50, 20W-40, 20W-50 ¢ Synthetic oil You can use synthetic engine oil that meets the same requirements given for conventional engine oil.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-13 ¢ Engine coolant q Changing the coolant q Checking the coolant level 1 FULL LOW 2 B00018 B00468 1) “FULL” level mark 2) “LOW” level mark Check the coolant level at each fuel stop. 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL” level mark.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 11-14 Maintenance and service on the coolant tank on top of the engine. Non-turbo models: MT. 7.4 US qt (7.0 liters, 6.2 Imp qt) AT. 7.3 US qt (6.9 liters, 6.1 Imp qt) Never attempt to remove the radiator cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boiling hot coolant when the cap is removed. 4. Install the under cover.
A1910BE-A-GSAAB.book Page 15 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-15 Be careful not to spill engine coolant when adding it. If coolant touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If engine coolant gets on the exhaust pipe, be sure to wipe it off. Do not splash the engine coolant over painted parts. The alcohol contained in the engine coolant may damage the paint surface. 6. Pour the coolant and fill to the reservoir tank’s “FULL” level mark.
A1910BE-A-GSAAB.book Page 16 Tuesday, September 6, 2005 8:37 AM 11-16 Maintenance and service ¢ Replacing the air cleaner element q Turbo models B00025 1) Air cleaner case cover 2) Air cleaner element B00024 1. Unsnap the two clamps holding the air cleaner case cover. 2. Open the air cleaner case cover and remove the air cleaner element. 3. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element. B00026 4.
A1910BE-A-GSAAB.book Page 17 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-17 q Non-turbo models direction of the arrow shown in the drawing. 1 B00364 2 B00361 1. Unsnap the two clamps holding the air cleaner case cover. B00363 1) Air cleaner case cover 2) Air cleaner element 3. Open the air cleaner case cover and remove the air cleaner element. 4. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element. 5.
A1910BE-A-GSAAB.book Page 18 Tuesday, September 6, 2005 8:37 AM 11-18 Maintenance and service ¢ Recommended spark plugs Spark plugs Drive belts Non-turbo models: FR5AP-11 (NGK) 2 1 Turbo models: ILFR6B (NGK) B A B00027 It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your Saab dealer. The spark plugs should be replaced according to the maintenance schedule in the “Saab Warranty and Service Record Booklet”.
A1910BE-A-GSAAB.book Page 19 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-19 in (mm) Deflection New belt Used belt A 0.28 – 0.35 (7.0 – 9.0) 0.35 – 0.43 (9.0 – 11.0) B 0.30 – 0.33 (7.5 – 8.5) 0.35 – 0.40 (9.0 – 10.0) Manual transmission oil ¢ Checking the oil level 1 B00469 Turbo model B00465 Non-turbo model 1) Yellow handle 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again.
A1910BE-A-GSAAB.book Page 20 Tuesday, September 6, 2005 8:37 AM 11-20 Maintenance and service ¢ Recommended grade and viscosity 1 F F Each oil manufacturer has its own base oils and additives. Never use different brands together. Oil grade: 1 2 API classification GL-5 L L 2 -30 -20 -10 0 10 20 30 -20 0 20 40 60 3. Pull out the dipstick again and check the oil level on it. If it is below the lower level, add oil through the dipstick hole to bring the level up to the upper level.
A1910BE-A-GSAAB.book Page 21 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-21 ¢ Recommended fluid up to normal operating temperature; 158 to 176°F (70 to 80°C) is normal. 2. Park the vehicle on a level surface and set the parking brake. 3. First shift the selector lever in each position. Then shift it in the “P” position, and run the engine at idling speed. Use one of the following types of automatic transmission fluid.
A1910BE-A-GSAAB.book Page 22 Tuesday, September 6, 2005 8:37 AM 11-22 Maintenance and service Front differential gear oil (AT vehicles) ¢ Recommended grade and viscosity ¢ Checking the oil level Each oil manufacturer has its own base oils and additives. Never use different brands together. Oil grade: 1 1 API classification GL-5 2 -30 -20 -10 0 10 20 30 40 B00372 -20 0 20 40 60 1) Upper level 2) Lower level B00472 1) Yellow handle 1.
A1910BE-A-GSAAB.book Page 23 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-23 Rear differential gear oil ¢ Checking the gear oil level Your vehicle may be equipped with a rear differential protector. The differential protector provides protection to the rear differential assembly during off-road use. Removal of the rear differential protector is not required when checking the oil level.
A1910BE-A-GSAAB.book Page 24 Tuesday, September 6, 2005 8:37 AM 11-24 Maintenance and service -30 -20 -10 -20 0 20 0 10 40 20 60 30 80 Power steering fluid 40 ¢ Checking the fluid level 100 90 85W 1 1 1 80W 75W/90 B00032 B00376 SAE viscosity no. and applicable temperature 1) Specified range B00375 1) Reservoir tank The power steering fluid expands greatly as its temperature rises; the fluid level differs according to fluid temperature.
A1910BE-A-GSAAB.book Page 25 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-25 Brake fluid Be careful not to burn yourself because the fluid may be hot. ¢ Checking the fluid level 1 When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank. And never use different brands together. Avoid spilling fluid when adding it in the tank. Be careful not to spill power steering fluid when adding it.
A1910BE-A-GSAAB.book Page 26 Tuesday, September 6, 2005 8:37 AM 11-26 Maintenance and service Never splash the brake fluid over painted surfaces or rubber parts. Alcohol contained in the brake fluid may damage them. Be careful not to spill brake fluid when adding it. If brake fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If brake fluid gets on the exhaust pipe, be sure to wipe it off.
A1910BE-A-GSAAB.book Page 27 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-27 Be careful not to spill clutch fluid when adding it. If clutch fluid touches the exhaust pipe, it may cause a bad smell, smoke, and/or a fire. If clutch fluid gets on the exhaust pipe, be sure to wipe it off. ¢ Recommended clutch fluid FMVSS No. 116, fresh DOT 3 or 4 brake fluid Avoid mixing DOT 3 and DOT 4 brake fluids even if they are of the same brand.
A1910BE-A-GSAAB.book Page 28 Tuesday, September 6, 2005 8:37 AM 11-28 Maintenance and service ¢ Checking the brake pedal reserve distance Clutch pedal (MT vehicles) Check the clutch pedal free play and reserve distance according to the maintenance schedule in the “Saab Warranty and Service Record Booklet”. ¢ Checking the clutch pedal free play ¢ Checking the clutch function 1 B00378 1) More than 2.
A1910BE-A-GSAAB.book Page 29 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-29 Replacement of brake pad and lining If you continue to drive despite the scraping noise from the audible brake pad wear indicator, it will result in the need for costly brake rotor repair or replacement. ¢ Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine Saab parts.
A1910BE-A-GSAAB.book Page 30 Tuesday, September 6, 2005 8:37 AM 11-30 Maintenance and service Parking brake stroke Tires and wheels When installing winter tires, be sure to replace all four tires. ¢ Types of tires q Winter (snow) tires Winter tires are best suited for driving on snow-covered and icy roads. However winter tires do not perform as well as summer tires and all season tires on roads other than snow-covered and icy roads. You should be familiar with type of tires present on your vehicle.
A1910BE-A-GSAAB.book Page 31 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-31 pressed against the curb when you park the vehicle. If you feel unusual vibration while driving or find it difficult to steer the vehicle in a straight line, one of the tires and/or wheels may be damaged. Drive slowly to the nearest authorized Saab dealer and have the vehicle inspected.
A1910BE-A-GSAAB.book Page 32 Tuesday, September 6, 2005 8:37 AM 11-32 Maintenance and service Abnormally low tire pressure (tread worn at shoulders) Abnormally high tire pressure (tread worn in center) Driving at high speeds with excessively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident.
A1910BE-A-GSAAB.book Page 33 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-33 Contact your Saab dealer if you notice abnormal tire wear. *: The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering performance. ¢ Wear indicators 1 3 When a tire’s tread wear indicator becomes visible, the tire is worn beyond the acceptable limit and must be replaced immediately.
A1910BE-A-GSAAB.book Page 34 Tuesday, September 6, 2005 8:37 AM 11-34 Maintenance and service bel and to have a speed symbol and load index matching those shown on the tire label. NOTE Using tires of a non-specified size detracts from controllability, ride comfort, braking performance, speedometer accuracy and odometer accuracy. It also creates incorrect body-to-tire clearances and inappropriately changes the vehicle’s ground clearance.
A1910BE-A-GSAAB.book Page 35 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-35 Aluminum wheels Use only those wheels that are specified for your vehicle. Wheels not meeting specifications could interfere with brake caliper operation and may cause the tires to rub against the wheel well housing during turns. The resulting loss of vehicle control could lead to an accident.
A1910BE-A-GSAAB.book Page 36 Tuesday, September 6, 2005 8:37 AM 11-36 Maintenance and service Hi Low 300172 Washer fluid level gauge id until it reaches the “Hi” level on the level gauge or the “Full” mark on the tank. Use windshield washer fluid. If windshield washer fluid is unavailable use clean water. In areas where water freezes in winter, use an anti-freeze type windshield washer fluid.
A1910BE-A-GSAAB.book Page 37 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-37 ¢ Windshield wiper blade rubber 1 1 1 B00380 B00504 1) Stopper 2. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while depressing the wiper blade stopper. 3. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 4. Hold the wiper arm by hand and slowly lower it in position.
A1910BE-A-GSAAB.book Page 38 Tuesday, September 6, 2005 8:37 AM 11-38 Maintenance and service ¢ Rear window wiper blade rubber 3. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks. B00061 2. Turn the wiper blade assembly counterclockwise. 1 B00332 1. Pull out the end of the blade rubber assembly to unlock it from the plastic support. 1) Stopper 4.
A1910BE-A-GSAAB.book Page 39 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-39 ends. If the rubber is not retained properly, the wiper may scratch the rear window glass. 5. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 6. Hold the wiper arm by hand and slowly lower it in position. 2. Pull the blade rubber assembly out of the plastic support. 1 B00066 B00505 1) Metal spines 3.
A1910BE-A-GSAAB.book Page 40 Tuesday, September 6, 2005 8:37 AM 11-40 Maintenance and service Battery Before beginning work on or near any battery, be sure to extinguish all cigarettes, matches, and lighters. Never expose a battery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. For safety, in case an explosion does occur, wear eye protection or shield your eyes when working near any battery. Never lean over a battery.
A1910BE-A-GSAAB.book Page 41 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-41 Fuses Never replace a fuse with one having a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse boxes. B00173 To remove the coin tray, open the cover and pull the coin tray out.
A1910BE-A-GSAAB.book Page 42 Tuesday, September 6, 2005 8:37 AM 11-42 Maintenance and service Main fuse 1 2 B00338 1) Good 2) Blown If any lights, accessories or other electrical controls do not operate, inspect the corresponding fuse. If a fuse has blown, replace it. 1. Turn the ignition switch to the “LOCK” position and turn off all electrical accessories. 2. Remove the cover. 3. Determine which fuse may be blown.
A1910BE-A-GSAAB.book Page 43 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-43 Installation of accessories Always consult your Saab dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 45 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-45 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) Low beam head light Premium Package vehicles Others High beam head light Front side marker light Spot light Room light Front turn signal Parking light Front fog light High mount stop light Rear turn signal light Cargo area light Brake/tail light Backup light License plate light Wattage Bulb No.
A1910BE-A-GSAAB.book Page 46 Tuesday, September 6, 2005 8:37 AM 11-46 Maintenance and service ¢ HID headlight bulbs 3 ¢ Halogen headlight bulbs 3 q Right-hand low beam light bulb 1 High-intensity-discharge (HID) bulbs are used for the low beams of the headlights. These HID bulbs use an extremely high voltage. To avoid the risk of an electric shock and resulting serious injury, you should not attempt to replace them.
A1910BE-A-GSAAB.book Page 47 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-47 1. Remove the air intake duct mounting bolt, then remove the air intake duct. 7. Install the bulb cover. q Left-hand low beam light bulb Replacement of the left-hand low beam light bulb requires removal of the battery and is thus dangerous. It must be performed by a Saab dealer. 700092 B00485 2. Remove the bulb cover by turning it counterclockwise. q High beam light bulbs 3.
A1910BE-A-GSAAB.book Page 48 Tuesday, September 6, 2005 8:37 AM 11-48 Maintenance and service ¢ Parking light q Right-hand side 1 B00484 700093 2. Remove the electrical connector from the bulb. 3. Replace the bulb with a new one. 4. Reconnect the electrical connector. At this time, be careful not to touch the bulb surface. 5. Install the bulb in the headlight assembly by turning it clockwise until it clicks. Turbo model B00483 Non-turbo model 1) Air intake duct 1.
A1910BE-A-GSAAB.book Page 49 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-49 5. Fit the bulb socket into the headlight assembly. 6. Install the bulb cover. q Left-hand side B00490 3. Hold the end of the parking light and remove the parking light. Replacement of the left-hand parking light bulb requires removal of the battery and is thus dangerous. It must be performed by a Saab dealer. ¢ Front turn signal light and front side marker light bulbs B00492 2.
A1910BE-A-GSAAB.book Page 50 Tuesday, September 6, 2005 8:37 AM 11-50 Maintenance and service ¢ Rear combination lights 1 1 2 2 B00494 1) Front side marker light 2) Front turn signal light 4. Lift the undercover. Insert your hand under the undercover and feel for the front turn signal light and front side marker light with reference to the following illustration. Remove the bulb socket from the headlight assembly by turning it counterclockwise.
A1910BE-A-GSAAB.book Page 51 Tuesday, September 6, 2005 8:37 AM Maintenance and service 11-51 2. Remove the side cover. 1 2 3 B00498 B00497 3. Remove the upper and lower bolts. Then, slide the rear combination lamp assembly to the rear and remove it from the vehicle. 1) Rear turn signal light 2) Brake/tail light 3) Backup light 4. Remove the bulb socket from the rear combination light assembly by turning it counterclockwise. 5. Pull the bulb out of the bulb socket and replace it with a new one. 6.
A1910BE-A-GSAAB.book Page 52 Tuesday, September 6, 2005 8:37 AM 11-52 Maintenance and service ¢ License plate light ¢ Dome light, map light and cargo area light B00461 B00499 1. Remove the mounting screws using a Phillips screwdriver. 2. Remove the cover and lens. 3. Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the lens and cover. 5. Tighten the mounting screws. 700104 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Specifications Specifications ..................................................... 12-2 Dimensions ............................................................. Engine ...................................................................... Electrical system .................................................... Capacities ................................................................ Tires .....................................................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 12-2 Specifications Specifications Specifications These specifications are subject to change without notice. ¢ Dimensions in (mm) Item 2.5-liter non-turbo 2.5-liter turbo Aero 3 2.5i model Drive system AWD Transmission type AT MT AT Overall length 175.6 (4,460) Overall width 66.7 (1,694) Overall height 57.7 (1,466) Wheel base 99.4 (2525) Track Front 57.7 (1,466) Rear 57.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Specifications 12-3 ¢ Engine Engine model EJ253 (2.5-liter, SOHC, non-turbo) Engine type EJ255 (2.5-liter, DOHC, turbo) Horizontally opposed, liquid cooled 4 cylinder, 4-stroke gasoline engine Displacement cc (cu-in) 2,457 (150) Bore ´ Stroke in (mm) 3.9 ´ 3.1 (99.5 ´ 79.0) Compression ratio 10.0 : 1 Firing order 8.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 12-4 Specifications ¢ Capacities Fuel tank 15.9 US gal (60 liters) Engine oil 4.2 US qt (4.0 liters) Transmission oil (MT) 3.7 US qt (3.5 liters) Transmission oil (AT) 9.8 US qt (9.3 liters) AT differential gear oil 1.3 US qt (1.2 liter) Rear differential gear oil 0.8 US qt (0.8 liter) Power steering fluid 0.7 US qt (0.7 liter) Engine coolant Turbo engine model Non-turbo engine model MT 7.8 US qt (7.4 liters) AT 7.7 US qt (7.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Specifications 12-5 NOTE Adjust the tire pressure to 36 psi (250 kPa, 2.5 kgf/cm2) when driving the vehicle with five people and cargo inside and at speeds exceeding 99.4 mph (160 km/h). ¢ Wheel alignment Item 2.5-liter non-turbo 2.5-liter turbo 2.5i model Aero 3 Drive system Toe AWD Front 0.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 12-10 Specifications Vehicle identification 1) 2) 3) 4) 5) 6) 7) 8) 9) 2 3 1 5 4 7 6 9 8 C00109 Vehicle identification number Vacuum hose connections label/ Emission control label Tire inflation pressure label Certification plate Bar code label (U.S.
A1910BE-A-GSAAB.book Page 1 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects Tire information .................................................. 13-2 1 Tire labeling ............................................................. 13-2 Recommended tire inflation pressure .................. 13-5 Glossary of tire terminology .................................. 13-6 Tire care – maintenance and safety practices ..... 13-7 Vehicle load limit – how to determine ................
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. (For Canadian resident’s information.) Consumer information and Reporting safety defects Tire information ¢ Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-3 which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “91” means 1,356 lbs (615 kg), “89” means 1,279 lbs (580 kg) Load indices apply only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load.
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 13-4 Consumer information and Reporting safety defects Maximum load rating applies only to the tire, not to the vehicle. Putting a load rated tire on any vehicle does not mean the vehicle can be loaded up to the tire’s rated load. s Construction type Applicable construction of this tire.
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-5 ¢ Recommended tire inflation pressure q Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows, Tire size P205/55R16 89V 16 ´ 6.5 JJ 17 ´ 7 JJ Front 32 psi (220 kpa, 2.2 kgf/cm2) 33 psi (230 kpa, 2.3 kgf/cm2) Rear 29 psi (200 kpa, 2.0 kgf/cm2) 32 psi (220 kpa, 2.
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 13-6 Consumer information and Reporting safety defects q Vehicle label Example: q Measuring and adjusting air TIRE AND LOADING INFORMATION SEATING CAPACITY : TOTAL 5 FRONT 2 : REAR 3 The combined weight of occupants and cargo should never exceed 408kg or 900lbs.
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-7 Maximum inflation pressure The maximum cold inflation pressure to which a tire may be inflated. Recommended inflation pressure The cold inflation pressure recommended by a vehicle manufacturer.
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 13-8 Consumer information and Reporting safety defects involves switching the front and rear tires on the right-hand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle. (Each tire must be kept on its original side of the vehicle.) Replace any damaged or unevenly worn tire at the time of rotation.
A1910BE-A-GSAAB.book Page 9 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-9 Total weight = 154 lbs (70 kg) + 662 lbs (300 kg) (Occupant) (Cargo) = 816 lbs (370 kg) 2. Calculate the available load capacity. Example 1B 2. Calculate the available load capacity by subtracting the total weight from the vehicle capacity weight of 900 lbs (408 kg). 800272 3. The result of step 2 shows that a further 84 lbs (38 kg) of cargo can be carried.
A1910BE-A-GSAAB.book Page 10 Tuesday, September 6, 2005 8:37 AM 13-10 Consumer information and Reporting safety defects on the vehicle label with the statement “The combined weight of occupants and cargo should never exceed 408 kg or 900 lbs”. the vehicle for the child to use, the calculations are as follows: For example, the vehicle has one occupant weighing 165 lbs (75 kg) plus cargo weighing 375 lbs (170 kg).
A1910BE-A-GSAAB.book Page 11 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-11 capacity weight by 32 lbs (15 kg), so the cargo weight must be reduced by 32 lbs (15 kg) or more. ¢ Determining compatibility of tire and vehicle load capacities The sum of four tires’ maximum load ratings must exceed the maximum loaded vehicle weight (“GVWR”).
A1910BE-A-GSAAB.book Page 12 Tuesday, September 6, 2005 8:37 AM 13-12 Consumer information and Reporting safety defects ferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Uniform tire quality grading standards This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance.
A1910BE-A-GSAAB.book Page 13 Tuesday, September 6, 2005 8:37 AM Consumer information and Reporting safety defects 13-13 The traction grade assigned to this tire is based on straightahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
A1910BE-A-GSAAB.book Page 14 Tuesday, September 6, 2005 8:37 AM 13-14 Consumer information and Reporting safety defects Reporting safety defects to the Canadian government If you live in Canada, and believe that your vehicle has a safety defect, you should immediately notify Transport Canada, in addition to notifying General Motors of Canada Limited. You may write to Transport Canada at Box 8880, Ottawa, Ontario, K1G 3J2.
A1910BE-A-GSAAB.
A1910BE-A-GSAAB.book Page 2 Tuesday, September 6, 2005 8:37 AM 14-2 Index A ABS (Anti-lock Brake System) .......................................... 7-16 Warning light ....................................................... 3-12, 7-17 Accessories ............................................................. 5-2, 11-43 Accessory power outlet ...................................................... 6-6 Active head restraint ........................................................... 1-4 Air cleaner element ....
A1910BE-A-GSAAB.book Page 3 Tuesday, September 6, 2005 8:37 AM Index 14-3 CHECK ENGINE warning light/Malfunction indicator lamp .............................................................................. 3-11 Checking Brake pedal free play ................................................. 11-27 Brake pedal reserve distance .................................... 11-28 Clutch function ........................................................... 11-28 Clutch pedal free play ..................................
A1910BE-A-GSAAB.book Page 4 Tuesday, September 6, 2005 8:37 AM 14-4 Index Electronic Brake Force Distribution (EBD) system ........... 7-18 Emergency Locking Retractor (ELR) ................................ 1-10 Engine Compartment overview ................................................. 11-6 Coolant ....................................................................... 11-13 Exhaust gas (Carbon monoxide) ............................... 6, 8-2 Hood ........................................................
A1910BE-A-GSAAB.book Page 5 Tuesday, September 6, 2005 8:37 AM Index 14-5 J Jack and jack handle ........................................................ 9-15 Jump starting ...................................................................... 9-8 K Key Interlock release ............................................................ Number .......................................................................... Reminder chime ............................................................ Keys ..............
A1910BE-A-GSAAB.book Page 6 Tuesday, September 6, 2005 8:37 AM 14-6 Index Power Door locking switches .................................................... 2-6 Steering ....................................................................... 7-15 Steering fluid ............................................................... 11-24 Windows ...................................................................... 2-17 Preparing to drive ...............................................................
A1910BE-A-GSAAB.book Page 7 Tuesday, September 6, 2005 8:37 AM Index 14-7 Speedometer ...................................................................... 3-6 SRS airbag (Supplemental Restraint System airbag) .. 4, 1-33 SRS airbag system monitors ............................................ 1-53 SRS airbag system servicing ............................................ 1-54 SRS airbag system warning light ...................................... 3-10 SRS side airbag .........................................
A1910BE-A-GSAAB.book Page 8 Tuesday, September 6, 2005 8:37 AM 14-8 Index Oil pressure .................................................................. 3-11 Seatbelt .................................................................. 1-8, 3-9 SRS airbag system ...................................................... 3-10 Warranties and maintenance ........................................... 8-13 Washing ........................................................................... 10-2 Waxing and polishing ...
