Raw 700 Manual
Table Of Contents
- page0_DE.PDF
- page1_DE.PDF
- page2_DE.PDF
- page3_DE.PDF
- page4_DE.PDF
- page5_DE.PDF
- page6_DE.PDF
- page7_DE.PDF
- page8_DE.PDF
- page9_DE.PDF
- page10_DE.PDF
- page11_DE.PDF
- page12_DE.PDF
- page13_DE.PDF
- page14_DE.PDF
- page15_DE.PDF
- page16_DE.PDF
- page17_DE.PDF
- page18_DE.PDF
- page19_DE.PDF
- page20_DE.PDF
- page21_DE.PDF
- page22_DE.PDF
- page23_DE.PDF
- page24_DE.PDF
- page25_DE.PDF
- page26_DE.PDF
- page27_DE.PDF
- page28_DE.PDF
- page29_DE.PDF
- page30_DE.PDF
- page31_DE.PDF
- page32_DE.PDF
- page33_DE.PDF
- page34_DE.PDF
- page35_DE.PDF
- page36_DE.PDF
- page37_DE.PDF
- page38_DE.PDF
- page39_DE.PDF
- page40_DE.PDF
- page41_DE.PDF
- page42_DE.PDF
- page43_DE.PDF
- page44_DE.PDF
- page45_DE.PDF
- Sheet1
- Drawing View1
- Drawing View2
- Drawing View4
- Drawing View5
- Drawing View6
- Drawing View8
- Drawing View9
- Drawing View10
- Drawing View11
- Drawing View12
- Drawing View13
- Drawing View14
- Drawing View15
- Drawing View16
- Drawing View17
- Drawing View18
- Drawing View19
- Drawing View20
- Drawing View21
- Drawing View22
- Drawing View23
- Drawing View24
- Drawing View25
- Drawing View26
- Drawing View27
- Drawing View28
- Drawing View29
- Drawing View30
- Drawing View31
- Drawing View32
- Drawing View33
- Drawing View34
- Drawing View35
- Drawing View36
- Drawing View37
- Sheet1
- page46_DE.PDF
- Sheet1
- Drawing View37
- Drawing View38
- Drawing View39
- Drawing View40
- Drawing View41
- Drawing View42
- Drawing View45
- Drawing View46
- Drawing View56
- Drawing View58
- Drawing View59
- Drawing View60
- Drawing View61
- Drawing View63
- Drawing View65
- Drawing View71
- Drawing View73
- Drawing View75
- Drawing View78
- Drawing View81
- Drawing View82
- Drawing View83
- Drawing View89
- Drawing View91
- Drawing View93
- Drawing View94
- Drawing View95
- Drawing View96
- Drawing View105
- Drawing View110
- Drawing View111
- Drawing View113
- Drawing View115
- Drawing View116
- Sheet1
- page47_DE.PDF
Note: Larger ID
Note: Smaller ID
Socket Head Cap
Screw M6x10mm
(HC124-S)
Washer
6x
14 x1.5mm
(HC194-S)
Bearing
10x
19x5mm
(HC422-S)
Washer
10x
16x1mm
(HC230-S)
Thrust Bearing
10x
18x5.5mm
(HC438-S)
Washer
10x
16x1mm
(HC230-S)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Washer
3x
4x0.5mm
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Blade Grip Arm
(H1045-S)
Uniball M3
(H0065-S)
Socket Head Cap
Screw M4x10mm
(HC102-S)
Blade Grip
(H1044-S)
NOTE:
Washer
10x
16x0.2mm
[HC232-S]
The HPS head should be assembled with one, 1mm shim
(HC230) on each side. The blade grips must move freely, but
they should not move just under their own weight. After
approximately 10/20 flights, please check preload, you can
add one or two 0.2mm shim (HC232) if preload has changed.
eg: Microlube
GL261
Box 1, Bag for page 11
LINKAGE ROD
ASSEMBLED
RADIUS ARM
ASSEMBLY
Already assembled
with 1 bearing
UNIBALL RADIUS
ARM ASSEMBLY
CENTER HUB
ASSEMBLY
Page 11
HEAD ASSEMBLY