English SAB 2500
GENERAL INFORMATION Main Features For your Safety Unpacking General Operation RCU 3 3 4 5 5 6 INSTALLATION Front Panel Rear Panel Connecting to TV& VCR using SCART support Connecting to TV using RCA support Connecting to Digital Amplifier MENU INFORMATION Main Menu 1. Edit Channel 1.1 TV Channel List 1.2 Radio Channel List 1.3 Delete All 2. Installation 2.1 Antenna Connection 2.2 Satellite List 2.3 Antenna Setup 2.4 Single Satellite Search 2.5 Multi Satellite Search 2.6 TP List 3. System Setup 3.
. Tools 4.1 Information 4.2 Factory Setting 4.3 SatcoDx Auto Programing 5. Game 6. Hot key 6.1 Info 6.2 EPG 6.3 Find 6.4 Numer 6.5 TV/Radio 6.6 Up/Down 6.7 Left/Right 6.8 Mute 6.9 Pause 6.10 OK 6.11 Audio 6.12 Recall 6.13 Fav 6.14 Teletext 6.
A Digital Satellite Receiver is a convenient product that allows you to view a variety of programs provided through satellite. This user's guide covers the installation of the DSR and the necessary steps to implement various features. This also explains special features available only in this DSR in detail, which will allow you to make full use of these features. Information confirmed in this document is subject to change.
For Your Safety To avoid electric-shock hazards, do not open the cabinet, refer servicing to qualified personnel only. Keep the receiver away from flower vases, tubs, sinks, etc., in order to avoid damaging the equipment. Do not expose the receiver un-der the sunlight. And keep it away from the heat source. Do not block ventilation holes of the Receiver so that air can circulate freely. When the abnormal phenomenon occur, you should cut off the power immediately.
Remote Control Batteries User's Gudide General Operation Throughout this manual you will notice that the everyday operation of the receiver is based on a series of user friendly on screen display and menus. These menus will help you get the most from your receiver, guiding you through installation, channel organizing, viewing and many other functions. All function can be carried out using the buttons on the RCU, and some of the function can also be carried out using the buttons on the front panel.
RCU Key Function Turns power ON/OFF of the DSR When watching a channel, mute the sound 0~9 TV/RADIO PR Enter number of the required menu item or select a channel number to watch Switches between TV and Radio mode Switches back to previous channel FAV Display the favorite group list SAT Display the satellite list Display the Find window INFO Show information of the current channel MENU Press this key one time to run menu onscreen Moves up / down a page in the list OK, LIST PR+, PR- EXIT EPG L
Rear Panel Front Panel Rear Panel CONNECT TO A DIGITAL AMPLIFIER CONNECT TO A PC FOR S/W UPGRADE Serial Number CONNECT TO TV USING A SCART CABLE CONNECT TO AUDIO R/L TO TV OR AUDIO TUNER CONNECT VIDEO TO TV USING RCA JACK LNB IN: CONNECT TO SATELLITE ANTENNA Connecting to TV using SCART support Satellite Dish Serial Number DSR IN TV SCART
Connecting to TV using RCA support Satellite Dish IN VIDEO AUDIO TV R L DSR Serial Number Connecting to Digital Amplifier IN SCART TV Satellite Dish Serial Number DIGITAL AUDIO CONVERTOR OR AMPLIFIER SPEAKER L DIGITAL AUDIO R
Main Menu Make sure that you have properly installed and connected the cables of the receiver well. If the receiver is the factory status or there is no program list, when power on, the Main Menu window will be displayed on the screen. During the normal TV/Radio mode, press MENU key on the RCU to enter into the Main Menu window. This menu consists of 5 major main menus as follow.
If there is no program, you can not exit from the Main Menu window by pressing MENU or EXIT key. System will inform "No channel" and the following items turn grey.
3. Press FAV key to move the FAV button upward. Select the program and press OK key to pop up the favourite group list. In the list, select the group that you want to add into and press OK key, and then you will find the favourite mark is displayed at the right side of the selected program. Press FAV key again to exit from the fav mode, and you will find the FAV button return to the origin position. 4. Press red colour key to move the Lock button upward.
7. Press blue colour key to enter into the Edit channel window. i . Sort (red colour key) Press red colour key to pop up the Sort dropdown list. Name(A-Z): The ascending order, omitting the $ character, the number is ahead, then the capital letter, at last the lowercase. Name (Z-A): The opposite order of the above Name (A-Z). Free/Scramble:: All FTA programs are listed ahead, while all scrambled programs are listed last. Lock: all locked programs are listed at the last. ii.
Numeric keys 1 Press numeric key repeatedly, display in circle .,*?!@1 2 ABC2 3 DEF3 4 GHI4 5 JKL5 6 MNO6 7 PQRS7 8 TUV8 9 WXYZ9 0 [space]_-0 If the name is empty, system will pop up a dialogue informing "Name" once yellow colour key is pressed. Press OK key to close this dialogue. iii. Delete (blue colour key) In Delete window, press blue colour key to move the Delete button upward. Select the program and press OK key to mark this program with the deletion mark.
2. Installation 1. Press OK key or key to pop up the "Input Password" dialogue, you can not enter into the menu unless the correct password is inputted. The default password is "0000". 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or key to move the focus to the left menu. 2.1 Antenna Connection Press keys to select between Motor Antenna and Fixed Antenna. 2.2 Satellite List 1. Press PR+, PR- keys to select the satellite up or down.
Longitude: You can press keys to switch between east longitude and west longitude. After pressing OK key, you can use numeric keys to edit the longitude, press EXIT key or the PR+, PR- keys to exit editing mode. The range of the longitude is from 1to 180 degree. If beyond this range, system will inform you "out of range" when you press yellow colour key on the RCU. After setting, press yellow colour key to save and exit, while press blue colour key to exit without saving. 4.
Part B: Motor Suppose that you have selected Moter Antenna in the Antenna Connection window. 1. LNB Type: Select the proper LNB type. 2. Motor Type: Select between DiSEqC1.2 and USALS. If you select DiSEqC1.2, the following Local Longitude and Local Latitude items will turn grey. 3. Delete All: Press OK key to pop up the dialogue "Are you sure to clear set satellite position of this tuner?".
5. Limit Setup: Press OK key to pop up the Limit Setup window. Limit Setup: Press keys to switch among Disable Limit, East Limit and West Limit. Limit Setup: Move cursor to the Limit Setup button. You can press or press key to turn west , key to turn east. Go to Reference: Press OK key to go to reference. If you select Disable Limit in the above Limit Setup item, this button will turn grey. 6. If select USALS, Delete All item will turn grey.
2.4 Single Satellite Search 1. Satellite : Press keys to select the satellite in circle. Or press OK key to pop up the drop-down list, then select the desired satellite in the list and press OK key to confirm. 2. FTA Only: Press keys to select between Yes and No. 3. Scan Channel: Press keys to select among TV+Radio, TV Channel, Radio. 4. Network Search: Select between No and Yes. This item turns grey when Auto Scan is selected in the following Scan mode item. 5.
2.6 TP List 1. Press PR+,PR- keys to select the proper satellite. 2. Press red colour key to pop up the Edit TP window. Frequency, Symbol rate: Press keys to add or reduce by step one. Or press numeric keys (0-9) to input the desired value. The range of the frequency is 300013450, while the range of the symbol rate is 1000~45000. The inputted value is beyond this range, the value will return to the origin value. Polarity: Press keys to switch between Vertical and Horizontal. 3.
5. Press blue colour key to pop up the TP Search window. FTA only, Scan Channel, Network Search: Press keys to select the proper option. Press OK key at the OK button to start searching. 3. System Setup 1. Press OK key or key to move the cursor to the right menu. 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or key to move the focus to the left menu. 3.1 Language 1. Press OK key to enter into the Language window.
3.3 Local Time Setting 1. Summer Time: Select between ON and OFF. "OFF" delegates the normal time. If select ON, time will add one hour. 2. GMT Offset: When select "ON" in GMT Usage item, system will get the date and time information from the screen automatically. Date and Time two items will turn grey. Select the proper option in the GMT Offset item. The default setting is GMT ON. 3.Date, Time: When select "OFF" in GMT Usage, Date and Time two items take effect, while GMT Usage turns grey.
3.5 Parental Lock Before entering into the Parental Lock window, you need input the correct password. The default password is 0000. 1. Menu Lock: Press keys to select between Off and On. If select "On" , you can not enter into the most window before entering the password. 2. Channel Lock: Press keys to select between Off and On. The default value is Off. If select "On", you can not view the locked channel set in Chanel List Edit window until you have inputted the correct password. 3.
3.8 Other 1. LNB Power: Select between Off and On. 2. Channel Play Type: Select among All, Free, Scramble. 3. Channel Change: Select between Freeze and Black screen. 4. Beeper: Select between Off and On. 4. Tools 1. Press OK key or key to pop up the "Input Password" dialogue, you can not enter into the menu unless the correct password is inputted. The default password is 0000. 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or key to move the focus to the left menu. 4.
5. Game 1. Press OK key or key to enter into the game. 2. Press PR+, PR- keys to move the cursor up or down. 3. Press EXIT key or key to move the focus to the left menu. 4. Select the game that you want to play and press OK key to enter into the window. 6. Hot Key 6.1 Info Press INFO key to pop up the Info bar. Press INFO key again to pop up the program guide of the current program. You can press keys to know the program guide of the future 16 days. 6.2 EPG Press EPG key to enter into the EPG window. 1.
3. Detail Information: In the EPG window, press PR+, PR- keys to select the channel and program, and press OK key to know the detail information of the current program. 4. Press green colour key to enter into the Timer window. You can add the current program to the Timer. If 8 timers is already, system will inform "Timer is full!'. 6.3 Find Press FIND key on to pop up the Find window. Use numeric keys to enter into the character and use the colour keys to realized the corresponding operation. 6.
6.10 OK 1. During the viewing or listening, press OK key to pop up the TV program list or the Radio program list. 2. Press PR+, PR- keys to select the channel up or down, and then press OK key to play this channel in full-screen. 3. Press keys to select the satellite. 4. Press MENU or EXIT key to close this window. 6.11 Audio 1. Press keys to enter into the Audio window. 2. Press keys to select among Left, Right, Stereo, and Mono. 3.
Problem Possible causes What to do The display on the front panel does not light up. Main cable is not connected. Check that the main cable is plugged into the power socket. No sound or picture, but the front panel shows red light. The receiver is in standby mode. Press the standby button. The satellite dish is not pointing at the satellite. Adjust the dish. Check the signal level in the Antenna Setup menu. No signal or weak signal.
