INSTRUCTION MANUAL Gas Ranges This manual contains important information regarding your purchased equipment. Please read the manual thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular maintenance guidelines outlined in this manual may void the warranty. Please keep it for future reference after installation and do not throw it away! This is a universal installation and operation instruction book which would apply to different models.
IMPORTANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS EQUIPMENT, WHOU SHOULD PERFORM THE INITIAL FIELD START-UP AND ADJUSTMENTS OF THE EQUIPMENT AS COVERED BY THIS MANUAL. IMPORTANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
• • • • • • • • Do not obstruct the flow of combustion and ventilation air. Do not spray controls or the outside of the equipment with liquids or cleaning agents Allow for hot parts to cool before cleaning or moving. This equipment should only be used in a flat, level position. Do not operate unattended. Any loose dirt or metal particles that are allowed to enter the gas lines on this equipment will damage the valve and affect its operation.
Regulator must be upright after installation. If regulator is not level during operation, performance problems may result After connecting the appliance to the gas system, check for leaks at joints and pipe fittings; to do so,use soapy water or a specific leak detector(spray). 9. Check the gas supply pressure after installation. 10. Gas supply pressure can be measured with a liquid-filled pressure gauge (e.g. a U shaped pressure gauge, minimum scale division0.1mbar)or a digital gauge.
OVEN Before using the oven, please clean the unit completely, especially the oven chamber. Remove all the packing materials and film from shipping. Before cleaning the stainless steel accessories, please make sure that the used detergent contains no corrosive substance and is okay for stainless steel surface cleaning (no chlorine based cleaners).Then dry with a clean cloth.
GASCONVERSION: Conversion from Natural Gas to Liquid Propane (LP) or vice versa may only be performed by the factory or its authorized service agent. CLEANINGNOTE: It is important to check the machine daily. Checking the machine regularly can avoid serious accidents. Stop using if user feels that there are some problems with the unit. Check the condition of the machine before and after using every day. 1. 2. Before cleaning, turn off all gas valves.
The pilot flame is on but the main burner can’t be ignited The main burner nozzle is clogged Unclog the nozzle The pilot flame is on but the main burner can’t be ignited The gas control valve is defective Replace the gas control valve Problem It has a light back sound when the gas supply is turned off PossibleCauses Solution Wrong orifice size for the gas supply Install proper orifice It has a light back sound when the gas supply is turned off The air shutter is too open Adjust the damper It h
Open burner Oven Griddle/Broiler 30,000BTU/pc*4 31,000BTU/pc N/A 30,000BTU/pc*6 31,000BTU/pc N/A GR36-G24 2 burners with 24" griddle +oven 30,000BTU/pc*2 31,000BTU/pc 20,000BTU/pc*2 GR36-G12 4 burners with 12" griddle +oven 30,000BTU/pc*4 31,000BTU/pc 20,000BTU/pc 30,000BTU/pc*10 31,000BTU/pc*2 N/A MODEL GR24 STYLE 4 burners with oven 6 burners with oven GR36 10 burners with oven GR60 GR60-G24 6 burners with 24" griddle+ oven 30,000BTU/pc*6 31,000BTU/pc*2 20,000BTU/pc*2 GR60-G