Cod. 0341.952 - Ed.01 11/00 STAMPATO SU CARTA RICICLATA.
3 25 53 29 28 27 26 4 10 11 12 13 14 15 16 17 9 Aufheizen... 18 8 19 7 20 6 5 21 We congratulate for having bought this top-quality espresso machine and thank you for choosing Saeco. Before operating the machine, we recommend to read the following instructions thouroughly which explain how to use, clean and maintain the machine.
4 5 30 31 41 33 44 45 36 46 47 37 38 48 39 40 50 42 43 2 3 4 5 6 7 32 Aufheizen...
80 DESCRIPTION OF SYMBOLS How to use the instructions These instructions cannot anticipate every possible use of the machine. For further information or questions concerning specific situations or problems, please contact the local dealer or manufacturer directly. B Reference to figures, parts of the machine and control elements are given by numbers or letters, as figure B exemplifies. The warning triangle shows all important safety indications to ensure the user’s safety.
82 83 A Electrical parts should never be in contact with water: danger of shortcircuit! Steam and hot water may cause burns. Never direct steam or water jets towards the body; special attention must be paid when touching the steam/hot water spout and the heating plate: danger of burns! B This machine must be used exclusively for the purposes it has been manufactured.
84 IMPORTANT SAFEGUARDS When using your coffee maker, basic safety precautions should always be followed, including the followed to reduce the risk of fire, electric shock, and/or injury to persons including the following: 1 ● Read all instructions. 2 ● Do not touch hot surfaces. Use handles or knobs. 3 ● To protect against electric shock, do not place cord, plug or appliance in water or other liquid. 4 ● Close supervision is necessary when any appliance is used by or near children.
85 MACHINE CONTROLS AND PARTS IMPORTANT SAFEGUARDS a) A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord. b) Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use.
7 88 DRAINAGE / PROGRAMMING THE MACHINE Remove water tank (11) from the machine, remove its cover (12) and fill it with cold water (approx. 2.4l). A valve on the tank bottom prevents water from escaping. Before installing the water tank in the machine, make sure the coffee bean container cover is properly fitted. 31 Install the water tank, slightly pressing over it to fit the valve which will open automatically. Do not fill the tank with an excessive quantity of water.
89 90 PROGRAMMING THE MACHINE Cup heating plate connection Royal Professional is equipped with a useful cup heating plate which can be disconnected, if required. Press keys to move the asterisk to item “CUP HEATER”. Press ENT to activate this function. The following message will be displayed: "CUP HEATER "ON " " The keys allow you to change the set options “ON” or “OFF”. Temperature selection With Royal Professional a precise adjustment of the coffee temperature can be executed.
91 92 PROGRAMMING THE MACHINE By means of keys move the asterisk to item “VENDING” and select it through the ENT key. From the displayed submenu it is possible to select one of the following items by means of the same keys . On the contrary, if the hot water selection key is pressed, the submenu can be quit. The following messages will be displayed: "CODE " " ****" "1 LARGE COFFEE " "TOTAL 1234...." "1 COFFEE " "TOTAL 1234...." "1 SMALL COFFEE " "TOTAL 1234...." "HOT WATER " "TOTAL 1234....
93 94 PROGRAMMING THE MACHINE Press the same keys to modify the selected value (for example to set a new servicing limit). Through ENT a new value can be saved. On the contrary, by pressing ESC the new value entering is stopped and, as a result, the former counter setting shall be considered. When the set limit has been reached, the coffee dispensing stops and the following two messages are displayed: The rinsing cycle needs about 1 litre of water (including final rinsing).
95 96 BREWING "DREGDRAWER FULL "READY FOR USE " " The machine does not stop: remove the grounds container and empty it. Grind adjustment If the coffee flows too quickly (coarse grind) or too slowly (fine grind) into the cup, adjust coffee grinder. The recommended grind level is position 5. Should grinding be too coarse, adjust it on a lower value (e.g. from 5 to 3). On the contrary, should grinding be too fine, adjust it on a higher value (e.g. from 5 to 7).
97 SAFETY DEVICES 36 Place a glass or cup under the steam/hot water spout (7), then press the hot water selection key. Hot water will be automatically dispensed. Steam dispensing To heat milk or other drinks. Always clean the spout with a damp cloth soon after the use; otherwise, it might be difficult to remove milk residues. Turn the steam knob (9), the display will show: "STEAM " Direct steam/hot water spout (7) on cup holder grill (3) and slightly open knob (9), turning it counterclockwise.
99 Central unit Clean central unit (22) whenever the coffee bean container is filled, or at least once a week. 100 CLEANING AND MAINTENANCE OPERATIONS "BREW UNIT MISS " The machine cannot dispense coffee. Switch off the machine and open service door (19). Remove grounds coffee container (1). Coffee grinder 41 Remove central unit (22), by holding the handle and shortly pressing the PRESS key. Wash the central unit with hot water; do not use any solvent.
101 102 DESCALING By means of keys , move the asterisk at the end of the line on the menu item Descaling and confirm the selection with the ENT key. The following message will be displayed: "DESCALING " " After approx. 45 minutes, when the procedure is accomplished, the following message will be displayed: "DESCALING "FINISHED function by pressing the ENT key. Note: By pressing the ESC key (hot water key), it is possible to quit descaling procedure.
103 TROUBLESHOOTING Trouble Possible causes Solution No message is displayed The machine is not getting power Turn the main switch on, check plug and fuse The service door is open Close the service door is BREW UNIT MISS. Properly fit and lock the central unit Clean the central unit (see page 98) The automatic coffee brewing does not start BREW UNIT BLOCK. WATERTANK EMPTY COF. BEANS EMPTY The automatic coffee brewing does not start DREGDRAWER MISS.
