English 02 INSTRUCTIONS FOR USE Type HD8763 02 EN Read carefully before using the machine. Register your product and get support at www.philips.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
2 ENGLISH Congratulations on your purchase of a Saeco Minuto One Touch Cappuccino full automatic coffee machine! To fully benefit from the support that Saeco offers, please register your product at www.philips.com/welcome. This user manual applies to HD8763. The machine is suitable for preparing espresso coffee using whole coffee beans, and it is supplied with a milk carafe so you can brew a perfect cappuccino in a quick and easy way.
ENGLISH ESPRESSO AND COFFEE BREWING ....................................................................25 Espresso and Coffee Brewing Using Coffee Beans ....................................................................................25 Espresso and Coffee Brewing Using Pre-Ground Coffee ...........................................................................26 MILK CARAFE..................................................................................................27 Filling the Milk Carafe ....
4 ENGLISH IMPORTANT Safety Instructions This machine is equipped with safety features. Nevertheless read the safety instructions carefully and only use the machine as described in these instructions to avoid accidental injury or damage. Keep this user manual for future reference. The term WARNING and this icon warn against possible severe injuries, danger to life and/or damage to the machine. The term CAUTION and this icon warn against slight injuries and/or damage to the machine.
ENGLISH 5 • Remove the mains plug from the wall socket: - If a malfunction occurs. - If the machine will not be used for a long time. - Before cleaning the machine. Pull on the plug, not on the power cord. Do not touch the mains plug with wet hands. • Do not use the machine if the mains plug, the power cord or the machine itself is damaged. • Do not make any modifications to the machine or its power cord. Only have repairs carried out by a service centre authorised by Philips to avoid a hazard.
6 ENGLISH • Children should be supervised to ensure that they do not play with the machine. • Never insert fingers or other objects into the coffee grinder. Caution • The machine is for household use only and is not intended for use in environments such as canteens, staff kitchens of shops, offices, farms or other work environments. • Always put the machine on a flat and stable surface. • Do not place the machine on hot surfaces, directly next to a hot oven, heater or similar source of heat.
ENGLISH 7 • Do not leave water in the water tank when the machine is not used over a long period of time. The water can be contaminated. Use fresh water every time you use the machine. Compliance with Standards The machine complies with art.13 of the Italian Legislative Decree dated 25 July 2005, no. 151 “Implementation of the Directives 2005/95/EC, 2002/96/EC and 2003/108/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment, as well as waste disposal”.
8 INSTALLATION Product Overview 1 2 3 4 5 6 7 8 9 10 19 11 12 13 14 20 21 15 16 17 18 22 31 24 25 26 27 28 29 30 23
ENGLISH General Description 1. Grinder adjustment knob 2. Coffee bean hopper 3. Pre-ground coffee compartment 4. Water tank + Lid 5. Coffee bean hopper lid 6. Control panel 7. Coffee dispensing spout 8. Full drip tray indicator 9. Cup holder grill 10. Drip tray 11. Coffee grounds drawer 12. Brew group 13. Coffee residues drawer 14. Service door 15. Water dispensing spout (removable) 16. Milk carafe 17. Power cord socket 18. Power button 19. Grease for the brew group 20. Power cord 21.
10 ENGLISH PREPARING FOR USE Machine Packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport. Machine Installation 1 Remove the machine from the packaging. 2 For best use, it is recommended to: • • • Choose a safe, level surface, where there will be no danger of overturning the machine or being injured.
ENGLISH 11 5 Rinse the water tank with fresh water. 6 Fill the water tank with fresh water up to the MAX level and reinsert it into the machine. Make sure it is fully inserted. Caution: Never fill the water tank with warm, hot, sparkling water or any other liquid, as this may cause damage to the water tank and the machine. 7 Remove the coffee bean hopper lid. 8 Slowly pour the coffee beans into the coffee bean hopper.
ENGLISH 12 Switch the power button to “I” to turn on the machine. The “ ” button flashes. 13 To turn on the machine simply press the “ ” button. The machine Yellow automatically primes the circuit. USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time, the following activities need to happen: 1) The machine will prime the circuit; 2) The machine will perform an automatic rinse/self-cleaning cycle. 3) You need to initiate a manual rinse cycle.
ENGLISH 13 Yellow Yellow 2 The bar under the icon shows the operation progress. When the process is completed, the machine stops dispensing automatically. 3 Then the control panel shows the machine warm-up icon. Automatic Rinse/Self-Cleaning Cycle When warm-up is complete, the machine automatically performs a rinse/ self-cleaning cycle of the internal circuit with fresh water. This takes less than a minute.
ENGLISH Manual Rinse Cycle During this process you activate the coffee brewing cycle and fresh water flows through the water circuit. This takes a few minutes. Green 1 Place a container under the coffee dispensing spout. Green 14 2 Check that the machine shows this display. 3 Select the pre-ground coffee brewing function by pressing the “ ” button. The machine shows this display. Note: Do not add pre-ground coffee to the compartment. 4 Press the “ ” button.
ENGLISH 15 ” button. The machine shows this display. 8 Press the “ ” button to start dispensing hot water. Green 7 Press the “ Green 9 This icon is displayed. The machine reminds you to install the water dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water. Red 10 Dispense water until the no water icon appears. Note: You can stop the manual rinsing by pressing the “ ” button.
ENGLISH 11 At the end, fill the water tank again up to the MAX level. Now the maGreen 16 chine is ready for coffee brewing. You will see this display. Note: When you haven’t used the machine for 2 or more weeks, the machine will automatically perform an automatic rinse/self-cleaning cycle after you switch it on. Thereafter you need to initiate the manual rinse cycle as described above.
ENGLISH 17 Measuring and Programming Water Hardness Water hardness measuring is very important in order to define the descaling frequency and to install the “INTENZA+” water filter (for more detail on the water filter, see next chapter). To measure the water hardness follow the steps below: 1 Immerse the water hardness test strip (supplied with the machine) in water for 1 second. Note: The test strip can only be used for one single measurement. 2 Wait for one minute.
ENGLISH Yellow 5 Press the “ ” button to increase the value or the “ crease the value. ” button to de- 6 Press the “ ” button to confirm the setting. 7 Press the “ Green 18 ” button to exit the programming MENU. The machine shows this display and is ready to brew. “INTENZA+” Water Filter Installation We recommend you to install the “INTENZA+” water filter as this prevents limescale build-up in your machine and preserves a more intense aroma of your coffee.
ENGLISH 19 3 Set the “INTENZA+” water filter according to the measurements performed (see previous chapter) and indicated on the base of the filter: A = soft water – equals 1 or 2 on the test strip B = hard water (standard) – equals 3 on the test strip C = very hard water – equals 4 on the test strip 4 Put the “INTENZA+” water filter into the empty water tank. Press it down until it cannot move any further. 5 Fill the water tank with fresh water and reinsert it into the machine.
ENGLISH Replacing the “INTENZA+” Water Filter Yellow Yellow Yellow When the “INTENZA+” water filter needs to be replaced with a new one, the following icon is displayed. 1 Replace the “INTENZA+” water filter as described in the previous chapter. 2 Press the “ ” button and scroll the pages by pressing the “ ” button until the following icon is displayed. 3 Select the “RESET” option. Press the " " button to confirm. Green 4 To exit, press the “ ” button.
ENGLISH 21 ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible. Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin, blend and roast. The machine is equipped with a self-adjusting system that allows the use of all types of coffee beans available on the market except for caramelized and flavoured coffee beans.
ENGLISH 1 Press and turn the grinder adjustment knob below the coffee bean hopper one notch at a time. Use the coffee grinder adjustment key provided with the machine. You will taste the difference after brewing 2-3 cups of coffee. 2 The reference marks inside the coffee bean hopper indicate the grind 2 Adjusting the Aroma (Coffee Strength) Choose your favourite coffee blend and adjust the amount of coffee to be ground according to your personal taste. You can also select the preground coffee function.
ENGLISH 23 Adjusting the Coffee Dispensing Spout The height of the dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use. Move the dispensing spout up or down with your fingers to adjust its height as shown in the image. The recommended positions are: For the use of small cups; For the use of large cups. Two cups can also be placed under the dispensing spout to brew two cups of espresso or coffee at the same time.
ENGLISH Adjusting the Coffee Length The machine allows you to adjust the amount of brewed coffee according to your taste and the size of your cups. Each time the “ ” or “ ” button is pressed, the machine brews a pre-set amount of coffee. Each button may be individually programmed for a specific brew setting. The following procedure describes how to programme the “ ” button. 1 Place a cup under the dispensing spout.
ENGLISH 25 ESPRESSO AND COFFEE BREWING Before brewing coffee, make sure that there are no warnings shown on the control panel, and that the water tank and coffee bean hopper are filled. Espresso and Coffee Brewing Using Coffee Beans 1 Place 1 or 2 cups under the dispensing spout. 2 To brew an espresso or a coffee, press the “ ” button to select the desired aroma. Green 3 Press the “ ” button for an espresso or the “ ” button for a coffee.
ENGLISH Espresso and Coffee Brewing Using Pre-Ground Coffee This function allows you to use pre-ground coffee. With the pre-ground coffee function you can only brew one coffee at a time. Green 26 1 Press the “ ” button to select the pre-ground coffee function. 2 Lift the pre-ground coffee compartment lid and add one scoop of preground coffee to the compartment. Use only the measuring scoop supplied with the machine. Then close the pre-ground coffee compartment lid.
ENGLISH 27 MILK CARAFE This chapter explains how to use the milk carafe to prepare a cappuccino or to froth the milk. Note: Before using the milk carafe, clean it thoroughly as described in the “Cleaning and Maintenance” chapter. We recommend that you fill the carafe with cold (~5°C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino. Whole milk or skimmed milk may be used depending on individual taste.
28 ENGLISH Inserting the Milk Carafe 1 If installed, remove the water dispensing spout as shown in the figure: - Press the two buttons on the side to unlock it and lift it slightly; Pull the water dispensing spout to remove it. 1 2 2 Slightly tilt the milk carafe. Insert it all the way into the guides of the machine. 3 Push the carafe towards the bottom while rotating at the same time, until it is locked at the drip tray. Do not use force while inserting the carafe.
ENGLISH 29 Emptying the Milk Carafe 1 Press the release buttons to remove the top of the carafe. 2 Lift the top of the carafe. Empty the milk carafe and clean it properly. Note: After each use, clean the milk carafe as described in the “Cleaning and Maintenance” chapter.
30 ENGLISH CAPPUCCINO BREWING Warning: Danger of scalding! Dispensing may be preceded by short sprays of milk and steam. Danger of burns! Wait until the end of the cycle before removing the milk carafe. 1 Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. Note: Use cold (~5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH 31 5 Press the “ ” button to start the dispensing. Green 6 The machine reminds you to insert the carafe and pull out the milk carafe dispenser. Yellow 7 This icon is displayed during pre-heating time required by the machine. Verde 8 When the machine shows the following icon, the machine pours the milk. Dispensing can be stopped by pressing the “ ” button. Verde 9 Once the milk froth has been poured, the machine dispenses the coffee. Dispensing can be stopped by pressing the “ ” button.
ENGLISH Adjusting the Cappuccino Length Each time the “ ” button is pressed, the machine pours a pre-set quantity of cappuccino into the cup. The machine allows you to adjust the amount of cappuccino brewed according to your taste and the size of your cups. 1 Fill the milk carafe with milk and install it in the machine. 2 Pull out the milk carafe dispenser to the right up to the “ ” icon. Place a cup under the dispensing spout.
ENGLISH 33 FROTHING MILK Warning: Danger of scalding! Dispensing may be preceded by short sprays of milk and steam. Danger of burns! Wait until the end of the cycle before removing the milk carafe. 1 Fill the milk carafe with milk. The level must be between the minimum (MIN) and maximum (MAX) indication on the milk carafe. Note: Use cold (~5 °C / 41°F) milk with a protein content of at least 3% to ensure optimum results when preparing a cappuccino.
ENGLISH ” button. The machine shows this display. 6 Press the “ ” button to select milk froth. Green 5 Press the “ Yellow Green 7 The machine reminds you to insert the carafe and pull out the milk carafe dispenser. 8 This icon is displayed during pre-heating time required by the machine. 9 The machine dispenses a predefined quantity of milk froth into the Green 34 cup. Dispensing can be stopped by pressing the “ ” button. 10 Put back the milk carafe dispenser by shifting up to the “ ” icon.
ENGLISH 35 Adjusting the Milk Froth Length Each time this function is selected, the machine dispenses a preset amount of milk froth into the cup. The machine allows you to adjust the amount of milk froth according to your taste and the size of your cups. 1 Fill the milk carafe with milk and install it in the machine. 2 Pull out the milk carafe dispenser to the right up to the “ ” icon. Place a cup under the dispensing spout. ” button. The machine shows this display.
Yellow ENGLISH 6 This icon is displayed during pre-heating time required by the machine. 7 When the desired amount of milk froth is reached, press the “ Green 36 ” but- ton. Now the “milk froth” button is programmed. Every time it is pressed, the machine will brew the same amount of milk froth that was programmed. DISPENSING HOT WATER Warning: Danger of scalding! Dispensing may be preceded by short sprays of hot water and steam.
ENGLISH 37 3 Place a container under the hot water dispensing spout. ” button. The machine shows this display. 5 Press the “ ” button to start the dispensing. Green 4 Press the “ Yellow Green 6 This icon is displayed. The machine reminds you to install the water dispensing spout. Check that the water dispensing spout is correctly installed. Press “ ” to confirm. The machine will start dispensing hot water. 7 This icon is displayed during pre-heating time required by the machine.
38 ENGLISH CLEANING AND MAINTENANCE Daily Cleaning of the Machine Caution: Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine. Your machine is continuously exposed to moisture, coffee and limescale! In this chapter it is described in detail which activities you need to perform at which frequency. Not doing this will ultimately make your machine stop working properly.
ENGLISH 39 4 Insert the coffee grounds drawer back into the drip tray and this into the machine. 1 2 Note: Also empty the drip tray and coffee grounds drawer when the full drip tray indicator is raised. Daily Cleaning of the Water Tank 1 Remove the small white filter or the “INTENZA+” water filter (if installed) from the water tank and wash it with fresh water.
40 ENGLISH Daily Cleaning of the Milk Carafe It is important that you clean the milk carafe daily or after each use as it preserves hygiene and ensures perfect milk froth consistency. 1 1 2 Warning: Danger of scalding! Dispensing may be preceded by short sprays of hot water and steam. Danger of burns! Wait until the end of the cycle before removing the milk carafe. 1 Press the release buttons to remove the top of the carafe. 2 Rinse the top of the carafe and the milk carafe with lukewarm water.
ENGLISH 41 5 Put the lid back onto the milk carafe. 6 Pull out the milk carafe dispenser to the right up to the “ 7 Place a container under the dispensing spout. ” button. The machine shows this display. 9 Press the “ ” button to select milk froth. Green 8 Press the “ ” icon.
ENGLISH Yellow Green 10 The machine reminds you to insert the carafe and pull out the milk carafe dispenser. 11 This icon is displayed during pre-heating time required by the machine. 12 Once the machine stops dispensing water, the cleaning is finished. Green 42 13 Put back the milk carafe dispenser by shifting it up to the " " icon. Remove the milk carafe and empty it. Weekly Cleaning of the Machine 1 Clean the seat of the drip tray.
ENGLISH 43 Weekly Cleaning of the Milk Carafe The weekly cleaning is more thorough since all milk residue is removed from the dispenser. 1 Press the release buttons to remove the top of the carafe. 1 1 2 2 Remove the lid. 3 Lift the milk carafe dispenser to remove it from the top of the carafe. The milk carafe dispenser is made up of five parts that must be disassembled. Each part is identified by a capital letter (A, B, C, D, E) as shown in the figures below.
44 ENGLISH 6 Detach the lid (C) from the milk carafe dispenser by pulling it down while slightly pressing on the sides. C 7 Disassemble further as shown in the figure. D 8 Pull the fitting (E) outwards from the milk frothing device. E 9 Clean all the parts thoroughly with lukewarm water. Note: You can also clean these parts in the dishwasher. 10 Reassemble the parts following the reverse order.
ENGLISH 45 Weekly Cleaning of the Brew Group The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week. 1 Turn off the machine by pressing the “ ” button. Wait until the “ button flashes and unplug the power cord. ” 2 Raise the coffee dispensing spout and remove the drip tray and coffee grounds drawer by pressing the side buttons. Only at this time open the service door. 1 2 3 2 3 To remove the brew group, press the «PUSH» button.
46 ENGLISH 5 Thoroughly wash the brew group with lukewarm water and carefully clean the upper filter. Caution: Do not use detergent or soap to clean the brew group. 6 Let the brew group air-dry thoroughly. 7 Thoroughly clean the inside of the machine using a soft, dampened cloth. 8 Make sure the brew group is in the rest position; the two reference signs must match. If they do no match, proceed as described in steps 9-10.
ENGLISH 47 11 Insert the coffee residues drawer in its seat and ensure that it is correctly in place. Note: If the coffee residues drawer is not correctly positioned, the brew group may not fit into the machine. 12 Insert the brew group in its seat again until it locks into place without pressing the “PUSH” button. 13 Insert the coffee grounds drawer with the drip tray back into the machine and close the service door.
48 ENGLISH Monthly Cleaning of the Milk Carafe For the monthly cleaning cycle we recommend using the “Saeco Milk Circuit Cleaner” to keep the entire circuit clean of milk residues. The “Saeco Milk Circuit Cleaner” can be purchased separately. Please refer to the maintenance products page for further details. Warning: Danger of scalding! Dispensing may be preceded by short sprays of hot water and steam. Danger of burns! Wait until the end of the cycle before removing the milk carafe.
ENGLISH 49 ” button. The machine shows this display. 6 Press the “ ” button to select milk froth. Green 5 Press the “ Yellow Green 7 The machine reminds you to insert the carafe and pull out the milk carafe dispenser. 8 This icon is displayed during pre-heating time required by the machine. Green 9 Once the machine stops dispensing water, repeat steps 5 - 8 until the carafe is emptied. Warning: Never drink the solution dispensed during this step.
ENGLISH 11 Remove the milk carafe and the container from the machine. 12 Rinse and fill the milk carafe with fresh water up to the MAX level. 13 Insert the milk carafe into the machine. Pull out the milk carafe ” icon. Place a container under the dispenser to the right up to the “ dispensing spout to activate the rinse cycle. ” button. The machine shows this display. 15 Press the “ ” button to select milk froth.
Green Yellow ENGLISH 51 17 This icon is displayed during pre-heating time required by the machine. 18 Once the machine stops dispensing water, repeat steps 13 - 16 until the carafe is emptied. 19 Remove the milk carafe and the container from the machine. Repeat steps 11 - 16 one more time. 20 Disassemble and wash the milk carafe as described in the “Weekly Cleaning of the Milk Carafe” chapter.
52 ENGLISH 2 Also lubricate the shaft. 3 Insert the brew group in its seat until it locks into place (see “Weekly Cleaning of the Brew Group” chapter). 4 Close the service door and insert the drip tray and coffee grounds drawer. Monthly Cleaning of the Brew Group with “Coffee Oil Remover” Besides weekly cleaning, we recommend running the cleaning cycle with “Coffee Oil Remover” after approximately 500 coffees or once a month. This operation completes the maintenance process for the brew group.
ENGLISH 53 1 Place a container under the dispensing spout. 2 Make sure the water tank is filled with fresh water up to the “MAX” level. 3 Put a “Coffee Oil Remover” tablet in the pre-ground coffee compart- Green ment. 4 Press the “ ” button to select the pre-ground coffee function. Do not add ground coffee. 5 Press the “ ” button to start the coffee brewing cycle. 6 Wait until the machine has dispensed half a cup of water. 7 Switch the power button on the back of the machine to “0”.
54 ENGLISH 8 Let the solution take effect for about 15 minutes. Empty the container. 9 Switch the power button on the back of the machine, to “I”. To turn on the machine, press the “ ” button. Wait until the automatic rinse cycle has been completed. 10 Remove the drip tray and the coffee grounds drawer, empty them and open the service door. Remove the brew group. 11 Wash the brew group thoroughly with fresh water.
ENGLISH 55 13 Press the “ Green ” button to select the pre-ground coffee function. Do not add ground coffee. 14 Press the “ ” button to start the coffee brewing cycle. 15 Repeat steps 13 to 14 twice. Empty the container. 16 To clean the drip tray, place “Coffee Oil Remover” tablet inside and fill it 2/3rds full with hot water. Let the cleaning solution take effect for about 30 minutes, then rinse thoroughly.
56 ENGLISH DESCALING The descaling process takes approx. 35 minutes. Yellow Limescale builds up inside the machine during use. It needs to be removed regularly as it may clog the water and coffee circuit of your machine. The machine tells you when descaling is needed. If the machine display shows the CALC CLEAN icon, it means that you need to descale it. Caution: Not doing this will ultimately make your machine stop working properly, and in this case repair is NOT covered by your warranty.
ENGLISH 57 2 Insert the empty milk carafe. 3 Remove the “INTENZA+” water filter from the water tank if it was in- Yellow Yellow Yellow stalled and replace it with the small white original one. Place the water tank back into the machine. 4 Press the “ ” button until the following display is shown. 5 Press the “ ” button to start the descaling process. 6 The machine reminds you to insert the carafe and pull out the milk carafe dispenser.
ENGLISH 9 Pull out the milk carafe dispenser to the right up to the “ Yellow Yellow Yellow ” icon. Place a large container (1.5 l) under both the milk carafe dispenser and the dispensing spout. 10 Press the “ ” button to start the descaling cycle. 11 The machine will start dispensing the descaling solution at intervals. The bar on the control panel shows the cycle progress. Note: The descaling cycle may be paused by pressing the “ ” button .To resume the cycle, press the “ ” button again.
ENGLISH 59 15 Empty the drip tray and place it back. 1 3 2 16 Install the milk carafe into the machine. Pull out the milk carafe Yellow ” icon. Place the container back dispenser to the right up to the “ under both the milk carafe dispenser and the dispensing spout. 17 Press the “ ” button to start the rinse cycle. Note: The rinse cycle may be paused by pressing the “ ” button. To resume the cycle, press the “ ” button again.
60 ENGLISH Green 21 When the amount of water needed for the rinse cycle has been completely dispensed, this icon on the side is displayed. Press the “ button to quit the descaling cycle. ” Yellow 22 The machine automatically primes the circuit. 23 The machine now carries out the warm-up and automatic rinse cycle to prepare for product brewing. 24 Remove and empty the container. 25 Empty the drip tray and place it back. 1 2 26 The descaling cycle is now complete.
ENGLISH 61 PROGRAMMING You can adjust the machine functions to your personal preference by accessing the program menu. Yellow Yellow Yellow Yellow Yellow Yellow The following settings can be adjusted Coffee temperature This function allows you to adjust the coffee brewing temperature. Timer (stand-by) This function allows you to manage stand-by time. Contrast This function allows you to adjust the contrast of the display to better view the messages.
Yellow ENGLISH Factory settings This function allows you to reset all factory values. How to Program the Machine Green In this example, it is shown how to program the display contrast. Proceed in the same way to program the other functions. The programming menu can only be accessed when the machine is on and shows this display. Yellow 1 Press the “ ” button to access programming. 2 The main screen will be displayed.
ENGLISH 63 4 Press the “ ” and “ ” buttons to increase or decrease the value of the Yellow function. 5 When the display value is changed, the “OK” message appears. Press the “ ” button to confirm the change. 6 Press the “ ” button to exit the programming menu. Note: The machine will automatically exit the programming menu if you do not push any button for 3 minutes. The values that have been changed but not confi rmed won’t be saved.
64 ENGLISH MEANING OF THE DISPLAY ICONS This machine is equipped with a colour-coded system to make the user’s understanding of the display signals easier. The icons are colour-coded according to the traffic light principle. Ready Signals (Green Colour) The machine is ready to brew products. The machine is ready to brew pre-ground coffee. The machine is brewing one cup of espresso. The machine is brewing one cup of coffee. The machine is brewing two cups of espresso.
ENGLISH 65 Ready Signals (Green Colour) Hot water dispensing. Milk froth brewing. The machine is frothing the milk for the cappuccino. The machine is brewing the coffee for the cappuccino. The machine is programming the amount of milk to dispense for cappuccino. The machine is programming the amount of coffee to be brewed for cappuccino. The machine is programming the amount of milk to dispense for milk froth. Insert the water dispensing spout and press the “ dispensing. Press “ ” to exit.
66 ENGLISH Warning Signals (Yellow Colour) The machine is heating up to brew beverages or dispense hot water/steam. The machine is performing the rinse cycle. Wait until the machine has completed the cycle. The machine needs the "INTENZA+" water filter to be replaced. The brew group is being reset due to machine reset. Refill the coffee bean hopper with coffee beans and restart the cycle. The machine automatically primes the water circuit. The machine needs to be descaled.
ENGLISH 67 Warning Signals (Red Colour) Completely insert the drip tray with the coffee grounds drawer into the machine and close the service door. Fill the coffee bean hopper. The brew group must be inserted into the machine. Empty the coffee grounds drawer. Wait about 5 seconds before placing it back. Fill the water tank. Exx Turn off the machine. After 30 seconds, turn it on again. Try this 2 or 3 times.
68 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could encounter with your machine. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Philips Saeco hotline in your country. The contact details can be found in the warranty booklet supplied separately or on www.philips.com/support. Machine actions The machine does not switch on.
ENGLISH 69 Machine actions Coffee is brewed slowly. (See note) Causes The coffee grind is too fine. Coffee leaks out of the dispens- The dispensing spout is clogged. ing spout. Frothed milk is too cold. The cups are cold. Solutions ‘Change coffee blend or adjust the grinder as explained in chapter “Adjusting the ceramic coffee grinder.’ Prime the circuit (see "Using the Machine for the First Time" chapter). Clean the brew group (see "Weekly Cleaning of the Brew Group" chapter).
70 ENGLISH ENERGY SAVING Stand-by The Saeco full automatic espresso machine is designed for energy saving proven by the Class A energy label. After 30 minutes of inactivity, the machine turns off automatically (unless a different stand-by time has been programmed). If a product has been brewed the machine performs a rinse cycle. In stand-by mode, the energy consumption is below 1Wh. To turn on the machine, press the “ ” button (if power button on the back of the machine is set to “I”).
ENGLISH 71 TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage - Power Rating Power Supply See label on the inside of the service door Housing material Thermoplastic material Size (w x h x d) 215 x 330 x 429 mm Weight 7.5 kg Power cord length 800 - 1200 mm Control panel Front panel Cup sizes Up to 152 mm Water Tank 1.
72 ENGLISH ORDERING MAINTENANCE PRODUCTS For cleaning and descaling, use Saeco maintenance products only. You can purchase the products at the Philips online shop (if available in your country) at www.shop.philips.com/service, from your local dealer or authorised service centres. If you have any difficulties obtaining maintenance products for your machine, please contact the Philips Saeco hotline in your country. The contact details can be found in the warranty booklet by-packed separately or on www.
ENGLISH 73 - Milk Circuit Cleaner: CA6705 - Maintenance Kit CA 6706
02 EN Rev.00 del 30-05-13 02 The manufacturer reserves the right to make changes without prior notice. www.philips.
