Register your product and get support at 02 English www.philips.com/welcome Type HD8836 / HD8837 SUP 037DR 02 EN OPERATING INSTRUCTIONS READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or appliance in water or other liquid. 4. Close supervision is necessary when the appliance is used by or near children. 5. Unplug from outlet when not in use and before cleaning.
CAUTION This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service center. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1. Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2.
GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffee using either coffee beans or ground coffee and is equipped with a device to dispense steam and hot water. The structure of the machine has been designed for domestic use only and is not suitable for continuous professionaltype operation. Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine.
Danger of Burns Never direct the steam/hot water wand towards yourself or others: Danger of scalding! Always use the handles or knobs provided. Machine Location - Suitable Location for Operation and Maintenance For best use, it is recommended to: • Choose a safe, level surface, where there will be no danger of overturning it or being injured. • Choose a location that is sufficiently well-lit, clean and near an easily reachable socket.
Coffee bean hopper lid Grinder adjustment knob Coffee bean hopper Control panel Dispensing spout Pre-ground coffee compartment Drip tray Full drip tray indicator Service door Brew group Coffee grounds drawer Wand protective gripper Steam/hot water wand Power button Drip tray Water hardness test strip Water tank Brew group lubricant Pre-ground coffee scoop Power cord Strong coffee brew button Long coffee brew button LCD Display Intenza water filter (Optional) ON/OFF button “Aroma” - Pre-ground coffe
INSTALLATION • Remove the water tank. For your own and for other people’s safety, carefully follow the instructions provided in the “Safety Regulations” section. • Fill the tank with fresh drinking water. Do not exceed the “max” level indicated on the water tank. Once filled, place the tank back into the machine. Machine Packaging The original packaging has been designed and constructed to protect the machine during transport. We recommend keeping the packaging material for possible future transport.
• Switch the power button to “I” to turn on the machine. Priming the Water Circuit • The display shows the ON/OFF icon. • Turn the selector dial clockwise to set it to the “ ” position. The machine starts the automatic priming of the circuit by letting out a preset quantity of water through the steam/hot water wand (Pannarello, if supplied). The bar under the icon shows the operation progress.
The following icon will be displayed. Using the machine for the first time or after a long period of inactivity. These simple operations will make it possible to always brew excellent coffee. Green 1 Place a large container under the dispensing spout. 2 Before starting the procedure, check that the following icon is displayed. Red 9 Dispense water until the no water signal is displayed, then turn the selector dial counter-clockwise to set it to the “ ” position.
Water hardness measurement Intenza Water Filter The water hardness measurement is very important in order to correctly manage the “Intenza” filter and the frequency with which the machine must be descaled. To improve the quality of the used water, it is recommended that you install the water filter. Immerse the water hardness test strip provided with the machine in water for 1 second. Note: The test strip is only valid for one measurement. Check how many squares change colour and refer to the table.
When the icon appears, press the “ “ button to access the machine programming menu. Black Press the “ “ button until the following page is displayed. Orange Press the “ “ button to select “ON” and press the “ “button to confirm. Orange Orange In this way, the machine has been programmed to inform the user of the need to replace the filter. Note: When an “Intenza” filter must be replaced with a new one, the function must be reset. Replace the filter as previously shown.
bean hopper. Do not pour coffee beans when the coffee grinder is working. The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used. Green At this point the button “ “ is programmed; each time it is pressed and released, the machine will brew the same amount of coffee that was just programmed. To make any adjustment, press and turn the knob inside the coffee bean hopper.
Selection must be made prior to brewing the coffee. The system sets the aroma according to the personal taste of the user. Dispensing Spout Adjustment Most cups on the market can be used with this coffee machine. The height of the dispensing spout may be adjusted to better fit the dimensions of the cups that you wish to use. Manually move the dispensing spout up or down to adjust its height by placing your fingers as shown in the figure.
The machine is adjusted to brew a true Italian espresso coffee. This feature may slightly lengthen the brewing time, allowing the intense flavor of the coffee to develop fully. Warning: Only add pre-ground coffee to the compartment. Other substances and objects may cause severe damages to the machine. Such damages will not be covered by warranty. Press and release: the “ ” button for an espresso coffee; the “ “ button for a long coffee. • The brewing cycle then starts.
• Turn the selector dial clockwise to the “ ” position. narello when provided) externally. In this way, all parts will be perfectly cleaned and free of any milk residue. • Place a container under the steam/hot water wand (Pannarello, if supplied). • The following icon will be displayed. Green • When the machine is ready to brew coffee, turn selector dial counterclockwise to set it onto the “ ” position. Residual water may dispense from the steam/hot water wand (Pannarello, if supplied).
• Immerse the steam/hot water wand (Pannarello, if supplied) in the milk to be heated. CLEANING AND MAINTENANCE General cleaning • Empty and clean the coffee grounds drawer daily, with the machine turned on. • Turn the selector dial counter-clockwise to set it to the “ ” position. Froth the milk by gently swirling the cup. • After dispensing steam for the desired time, turn the selector dial clockwise and set it back to the “ ” position to stop dispensing steam.
• It is recommended to clean the water tank daily. - Remove the small white filter in the water tank and wash it under running drinking water. - Reposition the small white filter in its housing by gently pressing and turning it at the same time. - Fill the water tank with fresh drinking water. • Empty and clean the drip tray daily. Perform this operation also when the float is raised. • Also clean the seat of the tray every week through the openings on the bottom of the machine.
• If the machine is off, turn it on by pressing the ON/OFF button. Wait for the machine to complete the rinse and warm-up process. DESCALING Limescale normally builds up with the use of the appliance. The display informs you when descaling is necessary: Warning! Remove the "Intenza" filter before adding the descaling solution. Orange Do not turn the machine off or put it in stand-by mode during the descaling process. Use the Saeco descaling product only.
• Pour the entire content of the Saeco concentrated descaling solution into the water tank and then fill the tank with fresh drinking water up to the MAX level. Place the tank back into the machine. Red • When the solution in the tank is finished, the icon on the side is displayed to indicate that the selector dial must be brought back to the “ ” position. • Place a container under the steam wand and another one under the dispensing spout. • The icon indicates that the tank must be rinsed and filled.
• When inserting the water-filled tank in the machine, the icon on the side is displayed; turn the selector dial clockwise to the " " position. • The icon indicates that the tank must be rinsed and filled. Red Red • Empty the containers used to collect the liquid dispensed by the machine. • The machine performs a fast rinse cycle. Rinse the water tank thoroughly and fill it again with fresh drinking water up to the MAX level. Place the tank in the coffee machine.
Red • The icon indicates that the water tank must be rinsed and filled. Rinse the water tank thoroughly and fill it again with fresh drinking water up to the MAX level. If the water tank is not filled up to the MAX level during descaling cycle phases, the machine could prompt to dispense more water. • When inserting the water tank again in the machine, the icon on the side is displayed. Press the " " button to quit the descaling cycle.
Programming commands PROGRAMMING Changes can be made on each page: The user can change some of the machine operating parameters to suit his/ her needs. Orange Enter the “menu” The programming menu can only be accessed when the machine is in “stand-by” mode. - The “ ” and “ “ buttons allow you to change the value of the function, among those appearing on the page. To change the machine status to stand-by mode, press the ON/OFF button.
Functions Programming example COFFEE TEMPERATURE This function allows you to adjust the coffee brewing temperature. In this example, we want to explain how to programme the display contrast. Proceed in a similar manner to change the other functions. Orange TIMER (STAND-BY) This function allows you to adjust the time the machine will go into stand-by mode after the last brewing. Change the machine status to stand-by mode.
CONTROL PANEL DISPLAY Ready Signals Warning Signals • The machine is ready for whole bean coffee brewing and hot water dispensing. • The machine is warming up to brew coffee and dispense hot water or steam. Green Orange • The machine is ready for pre-ground coffee brewing. Green • The machine is performing the rinse cycle. Wait until the machine automatically stops brewing the beverage. Orange • The machine is in the steam dispensing phase. Green • The machine must be descaled.
Alarm Signals • Return the hot water / steam knob to its proper position. • Start screen for descaling cycle activation. Press “ESC” to quit Red • Close the service door. Red • This screen is displayed when the descaling cycle is selected. From now on, the descaling cycle must be completed to Red • Refill the coffee bean hopper. Red • Open the knob to carry out the operation Red described. • Turn the machine off. After 30-seconds, turn it back on. Try 2 or 3 times. Red its end.
TROUBLESHOOTING Machine Actions Causes The machine does not turn on. The machine is not connected to the power Connect the machine to the power source. source. The cups are cold. Warm the cups with hot water. The hole of the steam wand is clogged. Clean the hole of the steam wand using a pin. Make sure that the machine is turned off and has cooled before performing this operation. Pannarello is dirty (if supplied). Clean the Pannarello.
TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specifications of the product. Nominal Voltage - Power Rating - Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See label on the inside of the service door Housing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
del 15-02-13 02 EN Rev.00 02 The manufacturer reserves the right to change the features of the product without prior notice. www.philips.