Installation Manual

ManualsBrandsSafari ManualsNew Products!V-Spec Snorkel to suit Toyota 200 Series Landcruiser 4.6-4.7L Petrol & 4.5L Diesel 1VD-FTV

Page 1 of 11

SS87HF

SAFARI V-SPEC SNORKEL

To Suit: Toyota LandCruiser 200 Series (Pre-Facelift)

4.5L V8 Twin Turbo Diesel (1VD-FTV Engine)

4.6L & 4.7L V8 DOHC VVT-i Petrol (1UR-FE & 2UZ-FE Engines)

N.B: Does Not Suit Models with Factory Raised Air Intake (Snorkel)

19/06/2017

ITEM

PART NO

DESCRIPTION

QTY

370-133-000

BODY - SNORKEL (SS87HF)

000-135-800

3 ½” AIR RAM ASSEMBLY

370-032-000

BRACKET - UPPER MOUNTING

000-002-100

BOLT - HEX - 6mm x 1.0 x 14mm (SEMS) - S/S

000-951

SCREW - S/T - 4.2mm x 13mm - S/S

000-960

INSERT - PLASTIC

370-435-000

GASKET - UPPER MOUNTING BRACKET

000-110

STUD - 8mm x 1.25 x 25mm - S/S

000-311-300

WASHER - BODY - 8mm x 30mm - S/S

000-376

WASHER - RUBBER - 8mm x 33mm x 3mm

000-205-300

NUT - NYLOC - 8mm x 1.25mm - S/S

370-967-000

BRACKET - GUARD SUPPORT

370-025-000

SLEEVE - LOWER INSERT (Rubber)

370-024-000

HOSE - AIR ENTRY

000-910

CLAMP - HOSE - 90/110mm - S/S

370-044-000B

DUCT - AIR CLEANER BASE INLET - S/S (Diesel Fitment Only)

000-093-100

BOLT - B/H CAP SCREW - 4.0mm x 0.7 x 10mm - S/S (Diesel Fitment Only)

000-300-350

WASHER - BODY - 4.0mm x 12mm - S/S (Diesel Fitment Only)

000-223-300

NUT - NYLOC - 4.0mm x 0.7mm - S/S (Diesel Fitment Only)

370-025-600

SLEEVE - AIR INLET SUPPORT - 94.5mm x 35mm - Zinc Plated (Diesel Fitment Only)

000-914/B

CLAMP - HOSE - No. 56 (BLACK)

370-016-000

GASKET - FOAM BODY (Self Adhesive)

370-017-000

TEMPLATE - GUARD PANEL

Summary of content (11 pages)

PAGE 1
SS87HF SAFARI V-SPEC SNORKEL To Suit: Toyota LandCruiser 200 Series (Pre-Facelift) 4.5L V8 Twin Turbo Diesel (1VD-FTV Engine) 4.6L & 4.7L V8 DOHC VVT-i Petrol (1UR-FE & 2UZ-FE Engines) N.B: Does Not Suit Models with Factory Raised Air Intake (Snorkel) 19/06/2017 ITEM PART NO DESCRIPTION 1 370-133-000 BODY - SNORKEL (SS87HF) 1 2 000-135-800 3 ½” AIR RAM ASSEMBLY 1 3 370-032-000 BRACKET - UPPER MOUNTING 1 4 000-002-100 BOLT - HEX - 6mm x 1.
PAGE 2
SS87HF SAFARI V-SPEC SNORKEL To Suit: Toyota LandCruiser 200 Series (Pre-Facelift) 4.5L V8 Twin Turbo Diesel (1VD-FTV Engine) 4.6L & 4.7L V8 DOHC VVT-i Petrol (1UR-FE & 2UZ-FE Engines) N.
PAGE 3
Align the guard panel template (Item 23) to the upper and rear edges of the right hand guard panel. Check alignment with the guard mounted indicator hole (if fitted to vehicle). Tape the template to the guard with masking tape. Mark the snorkel outlet hole position and profile and the 5 snorkel mounting hole positions with a felt tip pen. 4 Drill a pilot hole for each of the marked positions. Use the step-drill to drill the 5 mounting holes to 16mm diameter.
PAGE 4
NEW ZEALAND INSTALLATIONS ONLY : Safari have developed 2 methods of Snorkel A pillar attachment, for the conventional method please proceed with the current document alternatively please see the link below for further instructions. www.safari4x4.co.nz/apillarmounting 5 Install the upper mounting bracket (Item 3) to the snorkel body (Item 1) with hex bolts (Item 4). Apply Loctite 243 to each of the snorkel mounting studs (Item 8) and install finger tight into the snorkel body mounting inserts.
PAGE 5
8 Place a strip of masking tape along the A-Pillar and install the snorkel body (Item 1) to the guard panel. When the snorkel body is correctly positioned, mark the outline of the upper mounting bracket (Item 3) onto the masking tape as shown. 9 Remove the snorkel body (Item 1) from the vehicle and remove the upper mounting bracket (Item 3) from the snorkel body (Item 1).
PAGE 6
11 Install the 3 plastic inserts (Item 6) into the upper mounting bracket holes in the A-Pillar. Install the upper mounting bracket gasket (Item 7), the upper mounting bracket (Item 3) and secure with 3 self tapping screws (Item 5). 12 DIESEL FITMENT ONLY: Remove and discard the foam sealing tape from the air cleaner inlet snout. Using a small flat blade screwdriver remove and discard the pre-spinner from the air cleaner inlet. Copyright Safari 4x4 Engineering Pty Ltd Melbourne Victoria Australia – www.
PAGE 7
13 DIESEL FITMENT ONLY: Install the air cleaner base inlet duct (item 16) and mark the two hole positions as shown. Using a 4.0mm drill bit, drill the two marked hole positions. 14 DIESEL FITMENT ONLY: Apply Sikaflex adhesive sealant to the flange of the air cleaner base inlet duct (as shown), install the duct and fasten into position with M4 x 10mm button head bolt (item 17), M4 body washer (item 18) and M4 nyloc nut (item 19).
PAGE 8
16 INSTALLER OPTION: The air cleaner base contains a drain valve and a hole as shown. These can permit water to enter the air intake. Safari advises that the drain valve and drain hole should be sealed to ensure a watertight installation. 17 Remove the sealing foam strip from the air entry snout (Petrol Fitment Only). Measure in 18mm from the end of the air entry snout on the air cleaner base and mark around the entire circumference as shown.
PAGE 9
secure with a 90/110mm stainless steel hose clamp (Item 15). 19 Install the air cleaner base assembly back into the vehicle. Fasten with the original mounting hardware. Install the air cleaner element and air cleaner lid. Reconnect the air mass sensor plug. 20 Loosely install a 90/110mm stainless steel hose clamp (Item 15) onto the snorkel snout end of the air entry hose (Item 14) and ensure that the clamping bolt of the hose clamp is orientated for accessibility.
PAGE 10
21 Install the snorkel body (Item 1) to the guard panel. When aligned correctly to the guard panel and the upper mounting bracket, install the rubber washers (Item 10) and body washers (Item 9). Secure the snorkel body to the guard panel with nyloc nuts (Item 11) in accordance with the following: DIESEL ENGINE on all but the lower rear mounting stud. PETROL ENGINE on all mounting studs. Secure the snorkel body (Item 1) to the upper mounting bracket (item 3) with 2 hex bolts (Item 4).
PAGE 11
) at the guard panel end of the guard support bracket and then the M6 bolt at the engine bay end of the guard support bracket (Item 12). 23 Loosely install the black hose clamp (Item 21) to the base of the air ram (Item 2) and install the air ram to the snorkel body (Item 1). Align the air ram and tighten the hose clamp (Item 21). 24 Install the guard mounted indicator, inner guard liner, mud flap (and any other items that may have been removed) in accordance with the factory service manual. 25 N.