Product Manual

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
Left Side Panel 1 1854-02
Right Side Panel 1 1854-03
Screw Post 18 HFFMFB
Left Cabinet Rail 1 1970-15
Pointed Screw 4 1902-23
Right Cabinet Rail 1 1970-16
Top Panel 1 1854-01
Back Panel 1 1854-04
Bottom Panel 1 1854-05
Locking Cam 18 HFFMFC
Wood Dowel 4 H8MMDWL
Half-Shelf 1 1854-07
Small Machine Screw 4 1854-28
Hinge Bracket (Style 1) 1 1854-29
Hinge Bracket (Style 2) 1 1854-30
Door 1 1854-08
Bushing 2 1854-31
Lock (2 Keys not shown) 1 1854-13
Large Nut 1 1854-24
Caster Bracket 4 1854-10
Barrel Nut 8 1854-23
Bolt 8 1854-27
Lock Washer 8 1854-21
Caster 4 8917-25
Shelf Peg 4 HSFBNZ
Adjustable Shelf 1 1854-06
Drawer 1 1854-09
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
MODEL NUM-
BER
1854
1854-37: 1 of 2; Rev. 1; 12/04
TOOLS REQUIRED: Phillips Screwdriver; Ham-
mer or Mallet
Machine Floor Stand
For questions or concerns, please call
Safco Consumer Hot Line 1-800-664-0042
available Monday-Friday 8:00 AM to 4:30 PM (Central Time)
(English-speaking operators)
ASSEMBLY INSTRUCTIONS
Safco Products Company, New Hope, MN 55428
LETTER
CODE
DESCRIPTION
QTY.
PART NO.
PARTS LIST
Q
D
Q
F
Properly identify the two rails used!
The D Left Cabinet Rail is stamped
“CL” near the roller, while the F Right
Cabinet Rail is stamped “CR”.
USE THIS HOLE
FOR FRONT
SCREW
1
Work on a smooth, clean surface.
Locate the A Left Side Panel and the B Right Side Panel and position them with the
holes up, as shown below. Insert C Screw Posts into the holes along the top, back and
bottom of each panel, and tighten with a screwdriver (do not overtighten!)
Attach the D Left Cabinet Rail to the A Left Side Panel, with the roller facing the front
QQ
Q
A
Q
B
edge, using two E Pointed
Screws (start with the hole
closest to the roller). Do
the same with the F Right
Cabinet Rail on the B Right
Side Panel.
Q
Q
Q
Q
Q
C
Q
D
Q
E
Q
F
SLOT
SLOT
THROUGH HOLES
The G Top Panel has two fi nished edges, the H Back Panel
has no fi nished edges, and the I Bottom Panel has one
fi nished edge. Lay them down with the large holes facing up.
Insert six J Locking Cams into each panel, with the arrows
pointing toward the nearest SIDE edge.
Insert the four K Wood Dowels into the holes in the ends of the
L Half-Shelf. Tap with a hammer or mallet until they are fully
seated.
Using two M Small Machine Screws each, attach the N and
O Hinge Brackets to the corners of the P Door, opposite the
large hole. Make sure that the posts on the Brackets are closest
to the corner. Slip a Q Bushing over each post.
From the face of the Door OPPOSITE the screws in the Hinge
Q
Q
2
3
Q
Q
Q
Q
Q
Q
J
Q
FINISHED
EDGES
NO
FINISHED
EDGES
ONE
FINISHED
EDGE
Q
G
Q
H
Q
I
Q
Q
Brackets, insert the R
Lock through the large
hole, and fasten with the
S Large Nut so that the
pawl points straight out to
the side. Once securely
fastened, turn the Lock
with the Key so the pawl
is parallel to the edge.
Q
Q
Q
P
Q
K
Q
L
Q
Q
N
Q
O
Q
M
Q
Q
Q
R
Q
S
LOCK
PAWL
ASSEMBLED UNIT
MODEL 1854
Q
Q
Q
A
Q
B
Q
C
Q
D
Q
E
Q
F
Q
G
Q
H
Q
I
Q
J
Q
K
Q
L
Q
M
Q
N
Q
O
Q
Q
Q
P
Q
R
Q
S
Q
T
Q
V
Q
U
Q
X
Q
Y
Q
Z
Q
AA
Q
Q
Q
Q
W