Product Manual

ManualsBrandsSafco ManualsAccessoriesPublic Square Waste Receptacle Base

Container: Models 2981GN, 2982BR, 2983BG, 2984BR

Lid and Hardware Kit: Models 2987BL, 2988BL, 2989BL

2987-371 1 of 2; Rev. 3: 12/06

Public Square

Recycling Containers

Safco Products Company, New Hope, MN 55428

Select your preferred set of labels from the two sets

supplied (

H or I

). Carefully remove the center

strip of backing material from a label. Grasp label

as shown and line up with top edge of A Container

so that ends of label overhang container sides

equally. Press down at center of label, peel the

backing off one side of the label, and smooth out

toward one end, pushing out any air bubbles for a

smooth finish. Repeat for the other end; then apply

the rest of the labels from this set to each remaining

side in the same manner.

Black Lid w/2” wide slot 1 F72613A3

Screw 2 Z10310A3

Wire Hold-Down Ring 1 F52920A3

Plastic Clip 2 Z10425A5

Leveling Glide 4 Z30227A3

Label Set, 4 “Paper” 1 Z40736A6

Label Set, 4 “Newspaper” 1 Z40879A3

LETTER

CODE

DESCRIPTION

QTY.

PART NO.

LID AND HARDWARE KITS

Black Lid w/4” round hole 1 F72615A1

Screw 2 Z10310A3

Wire Hold-Down Ring 1 F52920A3

Plastic Clip 2 Z10425A5

Leveling Glide 4 Z30227A3

Label Set, 4 “Cans” 1 Z40735A7

Label Set, 4 “Glass” 1 Z40734A8

LETTER

CODE

DESCRIPTION

QTY.

PART NO.

2981GN 26” Base only, Green

2982BR 32” Base only, Brown

2983BG 38” Base only, Burgundy

2984BR 44” Base only, Brown

DESCRIPTION

CONTAINER (one only)*

Letter

Code

Plastic Tray 1 Z50719A6

Black Lid w/8” square opening 1 F72614A2

Screw 2 Z10310A3

Wire Hold-Down Ring 1 F52920A3

Plastic Clip 2 Z10425A5

Leveling Glide 4 Z30227A3

Label Set, 4 “Waste” 1 Z40733A9

Label Set, 4 “Plastic” 1 Z40880A0

LETTER

CODE

DESCRIPTION

QTY.

PART NO.

* Each of the above Containers includes

the following parts packed inside:

MODEL 2987BL

MODEL 2988BLMODEL 2989BL

Des. Pat. No. D332,681

Model

Number

Thread four F Leveling Glides into the holes in

the bottom of A Container. Turn the container

upright and adjust glides until the container sits

level without rocking.

Summary of content (2 pages)

PAGE 1
Public Square® Recycling Containers Container: Models 2981GN, 2982BR, 2983BG, 2984BR Lid and Hardware Kit: Models 2987BL, 2988BL, 2989BL Letter Code Des. Pat. No.
PAGE 2
3 Line up set of holes in hinged flange of B Lid with outer set of holes in inside rim of A Container. Fasten with two C Screws. 4 Slip two E Plastic Clips over the wire on welded side of D Wire Hold-Down Ring. Align clips with inner holes on inside rim flange, and press points of clips firmly into the holes. 5 Insert G Plastic Tray into bottom of container to catch occasional drips or leaks. TO INSERT PLASTIC BAGS: 6 Open lid, lift wire hold-down ring.