User Manual of DS-6100-ATA Digital Video Server User Manual of DS-6104HCI/6101HFI-ATA Series Video Server
User Manual of DS-6100-ATA Digital Video Server Index CHAPTER 1 INTRODUCTION ..................................................................................................................... 4 1.1 FUNCTIONS AND FEATURES ......................................................................................................................... 4 1.2 COMMON APPLICATION ...............................................................................................................................
User Manual of DS-6100-ATA Digital Video Server Thanks for purchasing the products of Hikvision. If you have any requests or questions, please contact us immediately. This manual is applicable to DS-6104HCI-ATA & DS-6101HFI-ATA Series Video Server with one IDE HDD interface for local recording. This manual will be updated on a regular basis without additional specific notice. The updates will be added to the new version of this manual.
User Manual of DS-6100-ATA Digital Video Server Chapter 1 Introduction DS-6104HCI-ATA & DS-6101HFI-ATA series video server adopts embedded Linux OS and TI DaVinci Processor that is completely independent of PC platform, and efficiently improves system performance. Firmware is burned into the FLASH, making the system more steady and reliable. DS-6104HCI-ATA & DS-6101HFI-ATA series video server has the function of compressing the video signal and audio signal simultaneously into H.
User Manual of DS-6100-ATA Digital Video Server 2. 3. 4. 5. Support one IDE HDD that can max support 2000GB. Support FAT32 files system Support HDD S.M.A.R.T technology. Support cycle or non-cycle record. Network Function 1. Support one 10M/100M adaptive NIC; 2. Support TCP/IP protocols; support video, audio, alarm, voice data, serial device data transmission through TCP/IP network; build-in WEB browser, support IE access. 3.
User Manual of DS-6100-ATA Digital Video Server Chapter 2 Installation 2.1 Hardware installation 2.1.1 Installation steps 1. 2. 3. Open packing case, and check the integrity; Take out things needed in installation; Connect cables needed (video signal input cable, audio signal input cable, RS485 cable and cable for LAN); 4. Take out stabilizer power supply and power on. 2.1.2 Installation notice Please read the following notice carefully. If you have any question, please contact us. Notice: 1.
User Manual of DS-6100-ATA Digital Video Server 3. Connect the ATA data cable correctly. 4. Plug the HDD power connector. 5. Cover and fix the video server box. Note: After you install the HDD, you must format it. You can use remote client software to format the HDD. 2.3 Panel description Front panel Interface Instruction (From left to right in turn) 1. HDD indicator lamp; 2. Tx/Rx indicator lamp; 3. Link indicator lamp; 4.
User Manual of DS-6100-ATA Digital Video Server 2. 3. 4. 5. 6. One audio output for voice talk. One RJ45 UTP network port and one RJ45 RS-485 PTZ port. 4 external alarm input and 2 relay output. 4 channels video input and audio input. Power supply adapter. 2.4 The pin definition of physical interfaces 2.4.1 PIN definition of RS-232 serial interface The DVS has one RS-232 standard serial interface, with RJ-45 connector.
User Manual of DS-6100-ATA Digital Video Server (2) 25-pin to 9-pin converter’s internal connection is like this: (3) If you don’t want to use 25-pin to 9-pin convertor to connect DVS and DTE through RS232 interface, you must use RJ45-DB9 cable. Its internal connection description is: (4) When the RS232 interface of the DVS connects with the DCE (such as MODEM), one end of the cable is the 8-pin RJ45 connector and the other is the DB25 male connector.
User Manual of DS-6100-ATA Digital Video Server 2.4.2 PIN definition of RS-485 serial interface 1 8 TXD+ TXDRXD+ RXDGND 8 7 6 5 2 2.4.
User Manual of DS-6100-ATA Digital Video Server - 11 -
User Manual of DS-6100-ATA Digital Video Server Chapter 3 Video Server Setup There are three kinds of methods to configure the parameters of video server. 1. Through Hyper Terminal (connect DVS with the PC through RS-232 serial ports) 2. Through client-end application software (connect DVS with PC through network) 3.1 Parameter Setup through RS-232 serial port Mainly set up IP parameters of the video server through serial port. The default IP address is 192.0.0.64.
User Manual of DS-6100-ATA Digital Video Server Step2: To name the connection name and to define the icon. Input a name (e.g. aa), select a icon, press “OK”, the dialogue box like Fig. 3.2 appears. Fig. 3.2 Select communication port Step 3”: to select the communication port. Select “com1” communication port in Fig3.2, press “OK”, the dialogue box as Fig. 3.3 will appear. Fig. 3.3 Serial ports parameter setup Step 4: Serial port parameters setup.
User Manual of DS-6100-ATA Digital Video Server Fig. 3.4 Hyper Terminal Interface Step 5: To close the window, the Fig. 3.5 will appear. Select “Yes” and Fig. 3.6 will appear: Fig. 3.5 Disconnect Fig. 3.6 Save Hyper Terminal session Step 6: Save the Hyper Terminal session for using next time.
User Manual of DS-6100-ATA Digital Video Server 3.1.2 Shell Commands under Hyper Terminal Please use the DTE cable and the DB9/DB25 convertor to connect PC with DVS RS-232 port. Step 1: Enter into the Hyper Terminal. Click “Start” “Programs” “Accessories” “Communications” “Hyper Terminal” “aa.ht”, the Hyper Terminal interface in Fig. 3.4 will appear. Step 2: Press “Enter” in Hyper Terminal, the prompt “#” appear, as in Fig. 3.7.
User Manual of DS-6100-ATA Digital Video Server Fig. 3.8 Check command The following is the introduction of getIp, setIp commands. getIp Function: get the fixed IP, subnet mask, gateway, command port, IP address of PPPoE dialup (the IP address of PPPoE will be 0.0.0.0 if there is no dialup or dialup is not successful). Parameter: none. Grammar format: Enter after input the command Explanation: Please pay attention whether the inputting letters are capital or low case.
User Manual of DS-6100-ATA Digital Video Server Fig. 3.9 Get parameters of IP, PPPoE setIp Function: set the IP, subnet mask and gateway of the device Parameter: IP address, subnet mask, gateway Grammar format: setIp IP: mask Explanation: Please pay attention whether the inputting letters are capital or low case. And separate the parameters by colons. Fig. 3.
User Manual of DS-6100-ATA Digital Video Server 3.2 Video Server HDD format Please refer to chapter 3.1 to get video server IP address. Then use remote client software to access video server. Please refer to client software user manual for detail information. 3.3 Video Server Recording Setup Please use remote client software to remote setup video server local recording parameters. 3.4 PTZ control Step1: Connect DS-6100-ATA RS-485 interface with PTZ. Please refer to RS-485 pin definition.
User Manual of DS-6100-ATA Digital Video Server 3.5 Remote setup video server parameters Before the configuration, please make sure that the PC and the video server has been established the network connection, you can confirm using PING command. Please refer to the user manual of DVRDVS client software for detail information. Fig.3.
User Manual of DS-6100-ATA Digital Video Server Chapter 4 Upgrade Firmware There are two methods to upgrade the DVS firmware. One is using shell commands to ask DVS to download firmware from TFTP server. The other is using PC client software. 4.1 Use Shell Command and TFTP Server Step 1: Before the update start you should do the follow steps: 1. Download the TFTP server from the internet, such as Cisco TFTP Server. Then put the firmware in the root directory of the Cisco TFTP Server. 2.
User Manual of DS-6100-ATA Digital Video Server Fig 4.3 Step 2: Then reboot the device and press any button in the pc keyboard again and again until the HIK # come out in the Hyper Terminal interface, show as Fig 4.4. Then input the “print” to check if the IP of the server and device is correct, also both of them should be in the same LAN. you can use the command “set serverip” to modified the server ip “set ipaddr” to modified the device ip “set netmask” to modified the mask ip Show as the Fig.4.5.
User Manual of DS-6100-ATA Digital Video Server Fig 4.5 Step 3: Input commend “save” and press enter button. Show as Fig.4.5. Step 4: Input the commend “update” and press enter button, then space button. After that the update will start. Show as Fig.4.6 Fig. 4.
User Manual of DS-6100-ATA Digital Video Server Step 5: After the update finished, please input the command “reset” and press the enter button. The device will reset. Show as Fig.4.7. Fig 4.7 4.
User Manual of DS-6100-ATA Digital Video Server Fig.4.8 Remote upgrading Click “Explore” button and select the firmware file. Fig.4.9 Then click “Upgrade” button, to complete the upgrading process of the video server firmware.
User Manual of DS-6100-ATA Digital Video Server Fig.4.
User Manual of DS-6100-ATA Digital Video Server Chapter 5 PPPoE Dialup Operation DS-6100-ATA video server supports remote access through network, through browser, through PPPoE or PPP dialup. Before using this function, please make sure that the software you used in your device support such functions or not. 5.1 Using PPPoE to establish connection In the local LAN, use the client software remote setup the DVS parameters. The setup dialog is looked as following: Fig.5.
User Manual of DS-6100-ATA Digital Video Server Fig.5.2 [Explanation] please make sure that ADSL Modem is installed. If it is the first time to set PPPoE parameters, it needs to reboot video server to establish the connection. 5.2 Client access DVS when using PPPoE There are two methods: One is to access using the current WAN IP address of the video server. When the video server is successful establish the network connection by using PPPoE mode, it will get the WAN IP address.
User Manual of DS-6100-ATA Digital Video Server the network connection with the video server to get the video images directly. Fig.5.3 Here the fixed WAN IP address of PC is 220.184.114.48. We call it as DNS IP. In that the PC, one demo analysis server software named IP Server is run. It can get the video server information, including the dynamic WAN IP address of the video server. Fig.5.
User Manual of DS-6100-ATA Digital Video Server Chapter 6 Frequent Ask Questions 1. Failure to control PTZ It is possible that the camera and equipment are not connected through RS485 port, or the wrong configuration of the decoder. 2. certain individual channel picture is un-normal Please check whether the video cable is well connected with the camera and the Embedded DVS 3.
User Manual of DS-6100-ATA Digital Video Server Appendix A Specifications Model DS-6101HFI-ATA Video compression H.264 Encode/Decode resolution 4CIF/DCIF/2CIF/CIF/QCIF Video input 1 Video input interface BNC(1.0Vp-p, 75Ω ), Support PAL, NTSC Frame channel) 4CIF: 25(P)/30(N) fps rate(per DS-6104HCI-ATA 4 4CIF: 2 fps DCIF/2CIF: 4fps CIF: 25(P)/30(N) fps Stream types Video/Video&Audio Support dual stream Yes Bit rate 32Kbps ~ 2Mbps adaptive. (Max.
User Manual of DS-6100-ATA Digital Video Server Appendix B Good list 1. One piece of DS- 6100HCI-ATA video server; 2. One CD contains client application and user manual; 3. One power cable; 4.
User Manual of DS-6100-ATA Digital Video Server Appendix C Customer Information Card User’s Name Company Name Post Address Postcode Phone Number E-mail Model Number of Product Serial Number of Product Purchase Date Distributor Suggestions: Mr./Mrs.
