Installation Guide

INSTALLATION OF STI-SA5500 SELECT ALERT SIREN/STROBE
All specifications and information shown were current as of publication and are subject to change without notice.
SA5500IS MARCH2020
2306 Airport Road
Waterford • Michigan • 48327-1209
Phone: [phone] • Fax: [phone]
E-mail: [e-mail] • Web: www.sti-usa.com
Taylor House • 34 Sherwood Road • Bromsgrove
Worcestershire • B60 3DR • England
Tel: [phone] • Fax: [phone]
E-mail: [e-mail] • Web: www.sti-emea.com
BATTERY INSTALLATION/REPLACEMENT
1. Unscrew lens to remove.
2. Loosen PCB screws (do not remove).
3. Gently rotate PCB without touching LED’s and
without damaging the reflectors.
4. Connect battery and slide under retainer.
5. Re-install PCB and tighten screws.
NOTES
1. Internal battery will provide backup power if loss of external power.
2. If no internal battery is used, remove all power and move S2-1 to
“OFF” position (see detail S2).
LOW BATTERY OPERATON
Replace battery when low battery condition occurs,
Low battery LED flashes 1x per 1 minute and sounder
beeps 1x per 3 minutes
WARNING: This product can expose you to chemicals including Dichloromethane, which is
known to the State of California to cause cancer, and Bisphenol A (BPA), which is known to the
State of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Three year warranty or a one year limited warranty (from date of purchase) on most products.
See website for details. Electronic warranty form at www.sti-usa.com/wc14.
AIL A
LE 5 : 1
A
B
PCB SCREWS
9 VDC BATTERY (NOT INCLUDED)
9 VDC BATTERY CONNECTOR
CIRCUIT BOARD
LENS
LENS
#6 x 2 1/2 in. SCREW
(2) PROVIDED
O-RING (2) PROVIDED
ELECTRONIC BASE
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1 1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#8-10 WALL ANCHOR (2) PROVIDED
S1 S2
REFLECTORS
LOW BATTERY
LED
FLASH RATE ADJUSTMENT
AIL A
LE 5 : 1
A
B
PCB SCREWS
9 VDC BATTERY (NOT INCLUDED)
9 VDC BATTERY CONNECTOR
CIRCUIT BOARD
LENS
LENS
#6 x 2 1/2 in. SCREW
(2) PROVIDED
O-RING (2) PROVIDED
ELECTRONIC BASE
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1 1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#8-10 WALL ANCHOR (2) PROVIDED
S1 S2
REFLECTORS
LOW BATTERY
LED
FLASH RATE ADJUSTMENT
AIL A
LE 5 : 1
A
B
PCB SCREWS
9 VDC BATTERY (NOT INCLUDED)
9 VDC BATTERY CONNECTOR
CIRCUIT BOARD
LENS
LENS
#6 x 2 1/2 in. SCREW
(2) PROVIDED
O-RING (2) PROVIDED
ELECTRONIC BASE
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1 1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#8-10 WALL ANCHOR (2) PROVIDED
S1 S2
REFLECTORS
LOW BATTERY
LED
FLASH RATE ADJUSTMENT
AIL A
LE 5 : 1
A
B
PCB SCREWS
9 VDC BATTERY (NOT INCLUDED)
9 VDC BATTERY CONNECTOR
CIRCUIT BOARD
LENS
LENS
#6 x 2 1/2 in. SCREW
(2) PROVIDED
O-RING (2) PROVIDED
ELECTRONIC BASE
DRILL 3/16 DIA. HOLES
1 1/4 in. DEEP WHEN USING ANCHORS
DRILL 7/64 DIA. HOLES 1 1/4 in. DEEP
WHEN ANCHORS ARE NOT USED
#8-10 WALL ANCHOR (2) PROVIDED
S1 S2
REFLECTORS
LOW BATTERY
LED
FLASH RATE ADJUSTMENT
DETAIL S1
See pg. 2
DETAIL S2
3.73 in.
(94.6 mm)
.94 in.
(23.8 mm)
2.83 in.
(71.8 mm)
1.02 in.
(26.0 mm)
3.87 in.
( 98.2 mm)
3.73 in.
(94.6 mm)
.94 in.
(23.8 mm)
2.83 in.
(71.8 mm)
1.02 in.
(26.0 mm)
3.87 in.
( 98.2 mm)
1 2 3 4 FUNCTION
1 LOW BATTERY NOTIFICATION ON
* 0 LOW BATTERY NOTIFICATION OFF
* 0 0 0 CONTINUOUS “ON”
0 0 1 DOUBLE LED ROTATION
0 1 0 3 FLASH - DELAY - 3 FLASH
0 1 1 SINGLE LED ROTATION (FAST)
1 0 0 FLASHING
1 0 1 INTENSITY RAMPING UP & DOWN
1 1 0 SINGLE LED ROTATION (SLOW)
1 1 1 RIGHT/LEFT ROTATION
S2 - LOW BAT. NOTIFICATION/STROBE CONTROL
1 2 3 4
1 ON
0 OFF
*Default Settings
SPECIFICATION
Input Standby Operating
9VDC < 14µA 0.95A
12VDC < 180µA 0.96A
24VDC < 170µA 0.49A
Operating Temperature
-4°F to 140°F (-20°C to 60°C)