Instruction manual

ManualsBrandsSaftronics ManualsConsumer electronicsGP5 Series

www.saftronics.com

START-UP PROCEDURE

FOR THE GP5 / FP5

TABLE OF CONTENTS

PAGE

INSTALLATION 2

EXAMPLE 1:

Start/Stop & Speed Changes via the Keypad

(Out of Box) 4

EXAMPLE 2:

Remote Start/Stop (2-wire) & Speed Changes

via Keypad 5

EXAMPLE 3:

Remote Start/Stop (3-wire) & Speed

changes via the Keypad 6

EXAMPLE 4:

Remote Start/Stop (3-wire) & Speed Changes

via a Remote Source 7

EXAMPLE 5:

Remote Start/Stop (3-wire) & Speed Changes

via the Speed Pot 8

EXAMPLE 6:

Remote Start/Stop (2-wire) & Speed Changes

via external source with 3 Present Speeds 9

ADJUSTING THE TRIM POT.

WARNING 11

Saftronics, Inc.

5580 Enterprise Pkwy., Ft. Myers, FL 33905

Telephone: (941) 693-7200

Fax: (941) 693-2431 P/N 027-2073

Summary of content (11 pages)

PAGE 1
www.saftronics.
PAGE 2
START-UP GUIDE GP5 / FP5 www.saftronics.com Start-Up Procedure for the GP5/FP5 The following procedure is to assist in the start-up of the GP5/FP5 inverter, by providing a step by step guide to installation, programming and basic operation of the GP5/FP5 inverter. The procedure is based on several common configurations used in the industry. For more detailed configurations and applications refer to the GP5/FP5 instruction manual (Part # 027-2005F) available at www.saftronics.com. Installation 1.
PAGE 3
START-UP GUIDE GP5 / FP5 www.saftronics.com Frequency Ref. 0.0 Hz Home Position Monitor U-01 Frequency Ref Accel Time 1 0.0 Sec Output Frequency 0.0 Hz Decel Time 1 0.0 Sec Output Amps 0.0 A U-01 Frequency Ref U-02 Output Frequency U-03 Output Current U-04 Output Voltage U-05 DC Bus Voltage U-06 Output Power U-07 Input Term.
PAGE 4
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 1: Start/Stop & Speed Changes via the Keypad (Out of Box) When the inverter is set up with the sequence (start/stop) and the reference (speed changes) via the keypad, that is considered local mode. Local mode is generally used during initial start up or to check the rotation of the motor. The inverter can be easily put in into local mode by pressing the LOCAL/REMOTE key.
PAGE 5
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 2: Remote Start/Stop (2-wire) & Speed Changes via Keypad S1 FS GP5/FP5 Control Wiring FC S2 (K1) Forward (K2) Reverse S3 S4 S5 For more info on the multi-function inputs ref. page 78 in the GP5/FP5 Instruction manual G S6 Shield to Terminal G SC FI FV This configuration is used when the Start/Stop is via an external source such as a PLC or relay.
PAGE 6
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 3: Remote Start/Stop (3-wire) & Speed changes via the Keypad (PB1) FS GP5/FP5 Control Wiring Start S1 Stop S2 FC FWD/ REV S3 Start Stop (PB2) SW 1 Forward Reverse S4 G For more info on the multi-function inputs ref.
PAGE 7
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 4: Remote Start/Stop (3-wire) & Speed Changes via a Remote Source External 4 to 20mA Source (+) (-) External 0 to 10Vdc Source FC Analog Common FI 4 to 20mA Reference Signal GP5/FP5 Control Wiring G S1 REV S2 (-) FC (K1) Forward (K2) Reverse S3 S4 S5 S6 For more info on the multi-function inputs ref.
PAGE 8
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 5: Remote Start/Stop (3-wire) & Speed Changes via the Speed Pot Optional Trim Pot (R2) (PB1) FS +15Vdc Start S1 GP5/FP5 Control Wiring 2.5KΩ Speed Pot (R1) Stop S2 Start Stop (PB2) S3 S4 G 2.5KΩ Shield Drain Wire FWD/REV S5 FI SW1 Forward Reverse S6 FV Frequency Ref. 0 to 10VDC FC Analog Common For more info on the multi-function inputs ref.
PAGE 9
START-UP GUIDE GP5 / FP5 www.saftronics.com Example 6: Remote Start/Stop (2-wire) & Speed Changes via external source with 3 Present Speeds External 0 to10Vdc Source (+) GP5/FP5 Control Wiring (-) FC FV External 4 to 20Ma Source (+) (-) Analog Common 0 to 10Vdc Freq. Ref. FWD S1 REV S2 (K1)Forward (K2) Reverse S3 S4 SW1 Multi-Step 1 S5 SW2 Multi-Step 2 S6 G Shield FC Analog Common FI 4 to 20ma Freq. Ref. For more info on the multi-function inputs ref.
PAGE 10
START-UP GUIDE GP5 / FP5 www.saftronics.com Table 6: Programming needed for Remote Start/Stop (2-wire) & Multiple Inputs for Speed Changes Parameter Display Description N001 Password 8 The inverter will perform a 2-wire reset. CAUTION: This parameter sets all parameters to their factory settings and all previous settings will be lost. When the inverter completes the reset, the parameter returns to a value of 1. N001 Password 3 Change to a value of 3, to access all parameter in the inverter.
PAGE 11
START-UP GUIDE GP5 / FP5 www.saftronics.com WARNING! Saftronics manufactures component parts that can be used in a wide variety of industrial applications. The selection and application of Saftronics products remains the responsibility of the equipment designer or end user. Saftronics accepts no responsibility for how it’s products may be incorporated into the final design.