Operation Manual

21 22
PAge heAder..... PAge heAder.....
OPERATING YOUR NEW APPLIANCE
Tamp Set
This function is for advanced use only.
Adjusting tamp parameters allows for fine
tuning of coffee tamping force & polishing
duration. Press SELECT dial to select Tamp
Force and rotate dial to select setting 1-9.
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
Press SELECT dial to confirm and begin
adjustment of the polishing time. Rotate
dial to select 2-7 seconds. Press SELECT
dial to set. Machine will beep once to
confirm settings.
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
Pre-Infusion
This function is for advanced use only.
Low pressure pre-infusion allows you to
control the pressure & duration of the
pre-infusion phase of the espresso
extraction. Press the SELECT dial to set.
The Pump Power setting will flash. Rotate
the SELECT dial to increase or decrease
the pre-infusion pressure. Press SELECT
dial to set and pre-infusion duration
(seconds) will flash. Rotate SELECT dial to
adjust. Press SELECT dial to set. Machine
will beep once to confirm settings.
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
Long Black Adjust
Sets both the espresso volume & the water
volume for all cup sizes and strengths.
Grind, dose & tamp the portafilter. Insert
the portafilter into the group head. Place
the appropriate cup under the portafilter
spouts. Press the SELECT dial to select
Long Black Adjust. Rotate the SELECT dial
to select the cup size & strength you want
to program.
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
SELECTSELECTSELECT
TEMP TEXTURETEMP TEXTURETEMP TEXTURE
OPERATING YOUR NEW APPLIANCE
Press the SELECT dial to start the espresso
extraction. When required espresso volume
is extracted, press the SELECT dial to stop
espresso extraction. Hot water delivery will
commence immediately. Once required
water volume has been reached press
the SELECT dial to stop water delivery.
Machine will beep once to confirm settings.
NOTE
This has only programmed the
espresso volume & the water volume
for that particular cup/strength
combination. You will need to
repeat the above steps if you wish
to customise further cup/strength
combinations.
At any stage during programming, press
MENU|EXIT to return to STANDBY mode.
NOTE
The MENU|EXIT button is disabled
when the machine is in coffee making
or Hot Water mode.
DEFAULT SETTINGS
The machine has the following
default setting:
1. Shot Temperature: 93˚C
2. Low Pressure Pre-infusion:
PP60, PT7 seconds
3. Milk Temperature: 60˚C
4. Auto Start: OFF (8:00am)
5. Auto Off: 1 Hour
6. Clock: 12:00
ADVANCED FEATURES
These functions should only be accessed
by experienced users. See below for
information on how to reset all
default settings.
To access Advanced Features Menu, with
the machine turned OFF, press and hold
the 1 CUP button, then press and hold the
POWER button together for 3 seconds.
Rotate the SELECT dial to select feature.
Press SELECT dial to access feature
settings.
Press MENU|EXIT button at any time to
exit Advanced Features.
+
POWER
Reset Default Settings (rSET):
Use this function to reset all programmable
values back to the default settings. rSET will
be displayed on the LCD. Press SELECT dial
to reset all settings to factory defaults.
+
POWER
Hrd3 will flash on screen. Machine is now in
Water Hardness mode. See below how to set.
Descale (dESc):
Use this function to access the step by
step de-scale procedure. The current step
will be displayed on the GRIND LCD.
Refer to page 35 for procedure.