the Dose Control ™ SCG600 Pro
CONTENTS 2 We recommend safety first 6 Operating your new appliance 5 Getting to know your new appliance 10 Care, cleaning & storage 11 Troubleshooting At Sage® we are very safety conscious. We design and manufacture appliances with your safety foremost in mind. We also ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.
WE RECOMMEND SAFETY FIRST • Always turn the appliance to the off position, switch off at the power outlet and unplug at the power outlet when the appliance is not in use. • Do not use the appliance if the power cord, plug, or appliance becomes damaged in any way. If damaged or maintenance other than cleaning is required, please contact Sage Customer Service or go to sageappliances.com • Any maintenance other than cleaning should be performed by an authorised Sage® service centre.
WE RECOMMEND SAFETY FIRST • This appliance can be used by persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge, only if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. • Do not operate the grinder without the hopper lid in position. Keep fingers, hands, hair, clothing and utensils away from the hopper during operation.
GETTING TO KNOW YOUR NEW APPLIANCE A A. Bean Hopper Lid B C. Hardened Stainless Steel Conical Burrs. Removable and Adjustable Upper Burr B. Bean Hopper D. Grind Size Collar E. GRIND TIME Dial F. START/CANCEL Button G. Grind Outlet H. 50mm blade C I. D Grind Tray ACCESSORIES J. E Adjustable Razor™ Dose Trimming Tool K. Portafilter Cradle 50–54mm F L.
OPERATING YOUR NEW APPLIANCE BEFORE FIRST USE Remove and safely discard all promotional labels and packing materials attached to your Sage® appliance. Wash hopper, and cradles in warm soapy water and dry thoroughly. Wipe exterior of grinder with a soft damp cloth and dry thoroughly. Place grinder on flat level surface and plug power cord into 220-240V outlet and switch Power ‘ON’. GRINDING FOR ESPRESSO COFFEE Use single wall filter baskets when grinding fresh coffee beans.
OPERATING YOUR NEW APPLIANCE Step 4: Trimming the Dose APPLY PRESSURE AT BOTH ENDS The adjustable Razor™ Dose Trimming Tool allows you to trim the puck to the right level for a consistent extraction. Select the correct width blade of the Razor™ to match the diameter of your filter basket. The Razor™ has three blades of varying widths: 58mm, 54mm and 50mm. The 58mm and 54mm are already fitted within the Razor™ body. The 50mm is separate.
OPERATING YOUR NEW APPLIANCE Step 5: Select Your Grind Size For espresso, we recommend starting with grind size setting 15 and rotating the Hopper (to adjust the Grind Size Collar) either coarser or finer. Step 2: Select the required amount of ground coffee by rotating the GRIND TIME dial. Step 3: Select Your Grind Size Rotate the Hopper to adjust the Grind Size Collar until it reaches the required brewing method range.
OPERATING YOUR NEW APPLIANCE COFFEE CHART * Brewing Method Grind Size Grind Setting Amount (Shot/Cup) Espresso Percolator Drip Fine Medium Medium Coarse 3 secs per cup 3 secs per cup 1-25 6 secs per shot 10 secs per 2 shots 26-34 French Press or Plunger Coarse 35-45 46-55 2 secs per cup *This coffee chart should be used as starting point to adjust your grind time and / or size, as both may vary when using different coffee bean types, age and degree of roast.
CARE, CLEANING & STORAGE CARE, CLEANING & STORAGE NOTE 1. Empty beans from the hopper and grind out any excess beans (see below). Do not use alkaline or abrasive cleaning agents, steel wool scouring pads, as these can damage the surface. 2. Unplug power cord from power outlet before cleaning. 3. Wash the hopper lid and bean hopper in warm soapy water, rinse and dry thoroughly. NOTE Please do not clean any grinder parts or accessories in the dishwasher. 4.
TROUBLESHOOTING PROBLEM Grinder does not start after pressing START/CANCEL button Motor starts but no ground coffee coming from grind outlet Can’t adjust the Grind Size Collar POSSIBLE CAUSE WHAT TO DO • Grinder not plugged in. • Plug power cord into power outlet. • Bean hopper not attached correctly. • Lock bean hopper into position. Refer to the Bean Hopper section on page 6. • Grinder has overheated. • Leave for 20 minutes to cool down before using again. • GRIND TIME dial is on 0 seconds.
Sage® Freephone (UK Landline): 0808 178 1650 Mobile Calls (National Rate): 0333 0142 970 www.sageappliances.co.uk customerservice@sageappliances.co.uk Register your product and get more from your purchase What’s on your mind? Product registration takes only a few minutes and ensures a record of your purchase. Registration also makes it easier to get support and advice on any questions or issues that you might have in the future.
