the Nutri Juicer™ Cold XL SJE830
Contents 2 5 6 8 9 Important Safeguards Components Assembly Care & Cleaning Troubleshooting SAGE® RECOMMENDS SAFETY FIRST At Sage® we are very safety conscious. We design and manufacture consumer products with the safety of you, our valued customer, foremost in mind. In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions.
power outlet and unplug at the power outlet when the appliance is not in use. • Do not use the appliance if the power cord, plug, or appliance becomes damaged in any way. If damaged and maintenance other than cleaning is required please contact Sage Customer Service or go to sageappliances.com • Any maintenance other than cleaning should be performed by an authorised Sage service centre • Children should not play with the appliance.
• Do not push food into the feed chute with your fingers or other utensils. Always use the food pusher provided. Do not place hand or fingers into the food chute when it is attached to the appliance. • Do not juice stone fruit unless seeds and/or stones have been removed.
Components D A J B C D I E F G H A. Food pusher (not dishwasher safe) B. Interlocking safety arm C. Juicer cover (dishwasher safe) D. Stainless steel filter basket (dishwasher safe) E. Pulp container (dishwasher safe) F. Filter bowl surround (dishwasher safe) G. Variable speed control and off dial H. Overload protection indicator light I. 2 litre juice jug and sealing lid with built in froth separator (dishwasher safe) J.
Assembly BEFORE FIRST USE Before using your juicer for the first time, remove and safely discard any packaging materials and promotional stickers and labels. Ensure the power cord is unplugged. Wash the filter bowl surround, filter basket, juicer cover, food pusher, pulp container and juice jug and lid in warm, soapy water with a soft cloth. Rinse and dry thoroughly. 1. Place motor base on a flat, dry surface such as a countertop.
. Slide the food pusher down the food chute by aligning the groove in the food pusher, with the small protrusion on the inside of the top of the feed tube. Food pusher groove Small protrusion inside feed tube 8. Place the pulp container into position by tilting and lifting the motor base slightly. Insert the pulp container under the juicer cover on the back ensuring it is supported by the juicer cover and motor base. 9. Fit the lid to the juice jug and position jug under juice spout.
Care & Cleaning Ensure the juicer is turned off by turning the juicer dial to the OFF position. Then unplug the power cord. CLEANING 1. Remove Juice Jug. 2. Remove Pulp Container. 3. Disengage Locking Bar, pull up entire Juice Collector Assembly and take to sink. Rinse all parts after use (except the motor base) under running water to clear away the majority of juice and pulp. Wash in warm soapy water with a soft cloth.
Troubleshooting Juicer will not work when switched ON • The safety locking arm may not be correctly engaged in the vertical operating position. Check the top cover is properly aligned and the locking arm is located firmly into the two grooves on either side of the juicer cover. • Motor overload protection may have operated (see below). Overheating with excessive loads • The juicer is equipped with an internal self-resetting overload to prevent the motor from damage under heavy or continuous loads.
Motor appears to stall when overload protection LED flashes • Wet pulp can build up under the juicer cover and stall the juicer if the juicer is used excessively without cleaning. If this occurs, disassemble and follow the cleaning instructions to clean the filter bowl surround, the stainless steel filter basket and the juicer cover. The juicer can also stall if excessive force is used to push produce down the feed chute.
Sage ® Freephone (UK Landline): 0808 178 1650 Mobile Calls (National Rate): 0333 0142 970 www.sageappliances.co.uk customerservice@sageappliances.co.uk What’s on your mind? Register your product and get more from your purchase Our constant aim is to improve the quality and features of our appliances. We welcome your comments and ideas in assisting our ongoing development. Product registration takes only a few minutes and ensures a record of your purchase.
