SAGEM F@st™ 1704 Quick Installation Guide
SAGEM F@stTM 1704 Sagem Communications SAS (hereafter referred to as Sagem Communications) thanks you for choosing the range of SAGEM F@stTM 1704 routers while hoping that it will provide you with full satisfaction. SAGEM F@stTM 1704 products adapt the ADSL function respectively on POTS (ITU G.992.1/3/5 Appendix A) and on ISDN (ITU G.992.1/3/5 - Appendix B). SAGEM F@stTM 1704 equipment include four ethernet interfaces (LAN1 to LAN4).
SAGEM F@stTM 1704 Contents 1. Contents of the pack ...................................................................................... 3 2. Safety instructions ......................................................................................... 4 2.1. Power supply source ............................................................................................................. 4 2.2. Location conditions ............................................................................................
SAGEM F@stTM 1704 1.
SAGEM F@stTM 1704 2. Safety instructions Power supply source • Do not cover the router’s mains adapter. • The router comes with its own mains adapter. Do not use another adapter. • This class II adapter does not need to be grounded (earthed). The connection to the electrical network should comply with the indications given on the label. • Use a readily accessible mains outlet located near the router. The power supply cord is 2 m long.
SAGEM F@stTM 1704 3. Connection Connecting your router Important Make sure that the router is not connected to your computer before you start the installation from the CD-ROM. Make the connections as shown in the diagram below. Line le ca b Note A "UK" mains adapter can be provided in option according to the customer. Connecting additional telephones Make the connections as shown in the diagram below.
SAGEM F@stTM 1704 4. Installation from the CD-ROM Installation by Wi-Fi interface Important 1. You selected the Wireless interface (Wi-Fi), click on Next. 2. Select the wireless connection mode (Wi-Fi). Make sure that the router is not connected to your computer before you start the installation from the CDROM. Note The installation procedure described below was undertaken in Windows VistaTM. Installation in other Windows® (98, ME, 2000 and XP) can be slightly different. 1.
SAGEM F@stTM 1704 2. The Internet connection screen appears. Enter your connection ID and password, then click on Next. Note The Wi-Fi security key field only appears if a Wi-Fi security (WEP 128, WPA-PSK and WPA2-PSK) is assigned to your router. The length of this field depends on the selected security. The Wi-Fi information is marked on your router. 3. Once you have filled in the Wi-Fi parameters, click on Next. 4. The Internet connection screen appears.
SAGEM F@stTM 1704 Installation of the Ethernet port 1. You selected the Use the Ethernet cable, click on Next. 2. Follow the instructions displayed on screen by plugging in the router supply, switching it on and connecting the ADSL line, then connect your computer to one of the four Ethernet sockets (LAN1 to LAN4) of the router by using the Ethernet cable. Installation of an additional computer Important Your router is already connected. 1. Insert the CD-ROM into the relevant drive of your computer.
SAGEM F@stTM 1704 5.
SAGEM F@stTM 1704 Router supervision The HTTP configuration tool lets you configure and monitor the router remotely. To access the HTTP configuration tool: 1. Open your browser. 2. Enter the router’s IP address or enter the following URL: http://myrouter 3. In the login screen that appears, enter your username and password. Note This information is provided by your Internet Service Provider (ISP). The welcome page of the HTTP configuration tool appears.
SAGEM F@stTM 1704 Internet information The following table presents the possible states of the Internet field: Status Message Meaning Adsl Down ADSL line not connected or not activated Not configured The Internet account must be configured Router rebooting Router is rebooting Green Connected The Internet account is configured Yellow Waiting for ISP ADSL line synchronising Red Access denied Incorrect Internet account Off 11
SAGEM F@stTM 1704 6. Advanced router configuration Use the HTTP configuration tool to access advanced router settings and configure your equipment according to your needs.
SAGEM F@stTM 1704 7. Troubleshooting Many sources of information are available to help you identify and resolve issues you may experience: • the LEDs on the front panel of the router (see Status of the LEDs on the front panel, page 9), • the HTTP configuration tool (see Router supervision, page 10). For step-by-step and advanced problem-solving procedures, use the Diagnostic tool available in the HTTP configuration tool.
SAGEM F@stTM 1704 Restarting your router To restart your router, use one of the following methods: • press the Power button located on the rear panel of the router, • click on the Reboot action of the HTTP configuration tool (see Router supervision, page 10).
253271827A Sagem Communications SAS All rights reserved. The information and specifications included are subject to change without prior notice. Sagem Communications tries to ensure that all information in this document is correct, but does not accept liability for error or omission. Non contractual document. All trademarks are registered by their respective owners. Simplified joint stock company - Capital 158.291.895 Euro - 440 294 510 RCS Paris - SAGEM is a registered brand from Safran Group.
