Schablone 2011_04_07 SX682 WiMAX / engbt / SX682_FUG_EN_9 / Cover_front.fm / 17.5.11 SX682 WiMAX User Guide – User This device works in a frequency band for which no general licence has been obtained from your National Authority for Frequency Management. Please contact your service provider or your National Authority for Frequency Management about licensing before putting this device into service.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681IVZ.fm / 17.5.11 Contents Schablone 2011_04_07 Contents For your safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681IVZ.fm / 17.5.11 Contents Schablone 2011_04_07 Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Setting the operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring Internet access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting up the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681IVZ.fm / 17.5.11 Schablone 2011_04_07 Contents Open Source Software used in the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty regarding further use of the Open Source Software . . . . . . . . . . . . . Open Source Software used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Safety.fm / 17.5.11 For your safety Schablone 2011_04_07 For your safety Please read the safety instructions carefully before putting into service. Safety precautions General safety instructions If you give the SX682 WiMAX to someone else, make sure you also give them its documentation. The SX682 WiMAX must only be used as described in these installation instructions.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Safety.fm / 17.5.11 Information on Specific Absorption Rate (SAR) Schablone 2011_04_07 Information on Specific Absorption Rate (SAR) This device meets the limits for protecting the health of the public from the effecs of exposure to electromagnetic fields when it is operated in connection with the designated antenna(s) like described in the user manual. Your device is a radio transmitter and receiver.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Safety.fm / 17.5.11 Schablone 2011_04_07 Information about the optional outdoor antenna Setting up the antenna mast: There should not be any obstructions (walls, trees etc.) in front of the antenna. The best results will be obtained if the outdoor antenna is in sight of the WiMAX base station (cf. Fig. 1). Fig. 1 If a line of sight is not possible, you can reflect the radio waves off neighbouring buildings.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Safety.fm / 17.5.11 Schablone 2011_04_07 Information about the optional outdoor antenna The appropriate earthing clamps must be used to create an equipotential bonding between a cable shield and an equipotential bonding bar that complies with regulations. Please observe the standard DIN VDE 0855-300 and find out more on the Internet at http://www.dehn.de.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Product_intro.fm / 17.5.11 SX682 WiMAX Schablone 2011_04_07 SX682 WiMAX What is WiMAX? WiMAX stands for "Worldwide Interoperability for Microwave Access", a modern wireless network technology that enables fast Internet connection even in remote areas. With WiMAX technology you are no longer dependent on a DSL infrastructure in your home or place of work. Instead, you connect your PC or network wirelessly to radio stations operated in your region by your provider.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Product_intro.fm / 17.5.11 Product features Schablone 2011_04_07 Product features Wireless high-speed Internet access with a transmission rate of up to 20 Mbps (14 Mbps downlink, 6 Mbps uplink) Standard compatibility: IEEE 802.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Product_intro.fm / 17.5.11 Product overview Schablone 2011_04_07 For information about the optional outdoor antenna, please refer to "Connecting the outdoor antenna" on page 16. For information on connecting the mains adapter, please refer to "Switching on the devices" on page 18. For information on the reset button, please refer to "Restarting and resetting the SX682 WiMAX" on page 19.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Product_intro.fm / 17.5.11 Schablone 2011_04_07 Product overview Name LED Meaning Phone: telephone Lights up green The phone connection is active and registered with a VoIP provider. You can make calls via the Internet. The telephone connection is not active or not registered with a VoIP provider. You cannot make calls via the Internet. The connected telephone is active: it is being used to make a call or there is an incoming call.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Installing the SX682 WiMAX Schablone 2011_04_07 Installing the SX682 WiMAX The SX682 WiMAX can only be used with the device's integrated antenna or with one of the following outdoor antennas: 3.5 GHz 18 dBi WiMAX Antenna Outdoor 2.6 GHz 15 dBi WiMAX Antenna Outdoor "Antenna cable 3 m" "Antenna cable 3 m" 3.5 GHz versions should be used for the European Economic Area.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Schablone 2011_04_07 Choosing your location If you use the integrated antenna: Position the SX682 WiMAX directly in a window, so that the side with the LEDs and connectors is pointing into the room, towards you. Wherever possible, position the SX682 WiMAX on one of the upper storeys. Note that obstructions, particularly doors and wall coverings containing metal can affect data transmission.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 System requirements Schablone 2011_04_07 SX682 WiMAX with outdoor antenna WiMAX network base station PC with SX682 WiMAX i When used with the integrated antenna or the outdoor antenna, the SX682 WiMAX complies with the regulations on limiting the effect of electromagnetic fields on the general population. System requirements To use the SX682 WiMAX, the following requirements have to be fulfilled.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Connecting the SX682 WiMAX Schablone 2011_04_07 Connecting the SX682 WiMAX Connect the SX682 WiMAX in the following order: 1. If you use the outdoor antenna, have it installed by a qualified electrician. Connect the antenna cable from outside to the SX682 WiMAX. 2. Connect the PC to the SX682 WiMAX. 3. Connect an analogue terminal (telephone, fax machine, answer machine). 4.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Connecting the SX682 WiMAX Schablone 2011_04_07 Connecting the PC ! Use either the Ethernet cable that is supplied or a standard network cable (CAT-5) to connect the device to the PC. It is not important whether the Ethernet cable has straight or crossed wiring. Always use a shielded Ethernet cable. Connecting SX682 WiMAX to the PC Connect one Ethernet cable plug to the Ethernet port on the SX682 WiMAX.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Connecting the SX682 WiMAX Schablone 2011_04_07 Connecting a telephone, fax machine or answer machine You can connect an analogue terminal, such as a telephone with cord, cordless telephone, fax machine or answer machine, and operate them via the Internet in future (Internet telephony/VoIP). i Depending on the connection plug on your analogue terminal, you may require an additional adapter (TAE socket on the RJ11 plug).
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Restarting and resetting the SX682 WiMAX Schablone 2011_04_07 Check the LEDs during startup: LEDs during startup: – The Power power supply LED lights up green, and the SX682 WiMAX starts a self-test. If the LED does not light up, check that the mains adapter is connected correctly and the power socket is live. – The LAN Ethernet LED is continuously lit green.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Installation.fm / 17.5.11 Restarting and resetting the SX682 WiMAX Schablone 2011_04_07 Returning the SX682 WiMAX to factory settings If you no longer have access to your SX682 WiMAX, you can also restore factory settings with the reset button on the back of the device. ! When the factory settings are restored, all personal settings are deleted. Press and hold the reset button for more than 5 seconds. The 4 RSSI LEDs will begin to flash green.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Configuration with the Web browser Schablone 2011_04_07 Configuration with the Web browser You do not need to install any software on your PC to configure your SX682 WiMAX; the configuration program is stored on the device. Open this software in the same way as an Internet page in the Web browser and make the required settings. Your settings are then stored directly on the device.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 User interface Schablone 2011_04_07 The user interface start page opens. If the login screen does not open: Check the connections; see "Connecting the SX682 WiMAX" on page 16. If you use a firewall on the PC, it must allow connection to the SX682 WiMAX. If applicable, switch off the firewall for a test; if you can then open the login screen, configure the firewall accordingly.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 User interface Schablone 2011_04_07 UI elements The user interface you open with the Web browser is divided into the following sections: 1 Home Basic Setup Wizard Advanced Settings Status 2 3 Language Logout 4 Operating Mode Internet ... ... 6 ... Antenna selection 5 1 Tab selection: Open the Home, Basic Setup Wizard, Advanced Settings or Status tabs to display the contents of each configuration area.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 User interface Schablone 2011_04_07 Buttons Open online Help. Click this button if you require information about the screen you currently have open. The corresponding Help topic is opened. Logout Button with which you end the connection between the PC and the SX682 WiMAX. Back Return to the previous screen in the Basic Setup Wizard. Next Move on to the next screen in the Basic Setup Wizard.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 User interface Schablone 2011_04_07 Opening online Help There is an online Help for each screen of the configuration program, which you can open directly on the screen. Click the question mark button at the top right. The online Help is shown in the right pane of the configuration program. If necessary, click Open Help window to open the online Help in a separate window.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 The Home page Schablone 2011_04_07 The Home page Once you have logged in successfully to the SX682 WiMAX, you will see the Home page for the device software. The start screen offers an overview of all areas of the configuration program: Menu Description Basic Setup Wizard Perform the basic configuration and set up the radio connection to the WiMAX network ( page 27).
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Basic Setup Wizard Schablone 2011_04_07 Basic Setup Wizard The Basic Setup Wizard helps you start up your device and guides you step by step through the configuration process with the most important settings.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Basic Setup Wizard Schablone 2011_04_07 Selecting the antenna Select whether you want to operate your SX682 WiMAX with an outdoor antenna or the integrated one. – Click the first option button if you want to use the integrated antenna. Your SX682 WiMAX must be positioned by the window with the cable connections pointing inwards and must be connected.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Schablone 2011_04_07 Basic Setup Wizard First check your access data by going back to the WiMAX configuration page ( page 27). If you have entered your access data correctly, adjust the antenna. If you are using the integrated antenna: Turn your SX682 WiMAX by approx. 45°. Correct: Incorrect: Click Ok to restart the scan. i You must not move the SX682 WiMAX during the scan.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Schablone 2011_04_07 Basic Setup Wizard If a line of sight is not possible, you can reflect the radio waves off neighbouring buildings. To do this, direct the SX682 WiMAX at the building it is to reflecting off and not at the WiMAX network base station. If you are using the outdoor antenna: The qualified electrician turns the antenna through 20° in the vertical axis. Then the scan is repeated by clicking the Ok button.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Schablone 2011_04_07 Basic Setup Wizard The quality of the radio connection is represented graphically by the Signal quality bar. The longer the bar is, the better the radio connection. Try to obtain the best possible radio connection setting. If you are using the antenna integrated in the SX682 WiMAX: Memorise the current location and alignment of your SX682 WiMAX, so that you can restore it if the connection is broken.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Basic_configuration.fm / 17.5.11 Basic Setup Wizard Schablone 2011_04_07 Setting up VoIP access If you have connected an analogue telephone to the Phone port of your device for Internet telephony, you set up your VoIP account here using the information you received from your VoIP provider. Activate the VoIP option to use Internet telephony for your device. Enter the access data for your VoIP account that you received from your VoIP pro- vider.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Advanced Settings Schablone 2011_04_07 Advanced Settings In the Advanced Settings menu, you can configure all the options for the SX682 WiMAX. If required, you can also change the settings you made using the Basic Setup Wizard. The following table contains the options available in this menu.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Setting the operating mode Schablone 2011_04_07 Setting the operating mode Via the operating mode, you define the role your SX682 WiMAX will play when establishing and administering Internet connections. You can run your SX682 WiMAX in the following operating modes: Router Your SX682 WiMAX serves as an Internet router for the network components connected to the LAN port, i.e.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Configuring Internet access Schablone 2011_04_07 Configuring Internet access If you have configured the SX682 WiMAX using the Basic Setup Wizard, you have also configured your Internet access. You can check or change these settings in the Internet menu.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Configuring Internet access Schablone 2011_04_07 Always on This gives the users in your network a constantly active Internet connection. Only choose this setting if your Internet tariff is not time-dependent. Choose this option if you use Internet telephony, otherwise you cannot receive incoming calls. If necessary you can terminate the Internet connection manually ( page 26).
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Schablone 2011_04_07 Port Forwarding i This function is not available in Bridge operating mode, see "Configuring Internet access" on page 35. PCs in your network should be protected by a separate firewall. You can set up protection against DoS (Denial of Service) attacks in Bridge mode via the local network configuration, see "LAN configuration" on page 39.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Schablone 2011_04_07 Port Forwarding i This function is not available in Bridge operating mode, see "Configuring Internet access" on page 35. Opening the firewall for a selected PC (Exposed Host) You can set up a client in your local network to be a so-called "exposed host".
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 LAN configuration Schablone 2011_04_07 LAN configuration With the help of the LAN configuration you can change the preset values for the computer name and the private IP address for your SX682 WiMAX and configure the integrated DHCP server. Open the Advanced Settings tab and select Local Network. The preset IP address is 192.168.2.1. This is the private IP address of the SX682 WiMAX.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Schablone 2011_04_07 Setting up Internet telephony (VoIP) Assigning static IP addresses to individual PCs Even if you have activated the DHCP server, you can still assign a static IP address to individual PCs (e.g. when setting up these PCs for NAT functions). Enter the MAC address of the PC to which you want to assign a static IP address and the IP address you wish to assign to the PC.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 Setting up Internet telephony (VoIP) Schablone 2011_04_07 Enter the access data for your VoIP account that you received from your VoIP pro- vider. You can normally keep the default settings, unless your provider explicitly requires other values.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Advanced_configuration.fm / 17.5.11 WiMAX configuration Schablone 2011_04_07 WiMAX configuration On this page you enter the data for authentication of your device on the WiMAX base station. You will need the access data supplied by your WiMAX operator for this. If you have executed the Basic Setup Wizard, you will already have entered these details there. If necessary you can change them here.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Administration.fm / 17.5.11 Administration Schablone 2011_04_07 Administration The user interface Administration menu includes several helpful functions for administering your SX682 WiMAX.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Administration.fm / 17.5.11 Restoring factory settings Schablone 2011_04_07 Changing the password Enter the current password in the Current password field. If no default system password has been set, leave this field empty. Enter a new password in the New password field. – Select any series of characters with a minimum length of 4 and a maximum length of 20 characters.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Administration.fm / 17.5.11 Restart Schablone 2011_04_07 Restart If the SX682 WiMAX is not operating properly, you can reboot it. It should then be ready for use again. Open the Advanced Settings tab and on the Administration menu select Restart. Click Ok to reboot the device. A window will appear prompting you to confirm the procedure.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Status.fm / 17.5.11 Status Schablone 2011_04_07 Status You can check the status of your SX682 WiMAX with the pages in the Status menu. The menu is divided into several individual pages opened by clicking the entries in the menu area. To help with orientation, in the following sections the path is placed first so that you can quickly find the status messages described.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Status.fm / 17.5.11 Internet Schablone 2011_04_07 If necessary, click the Refresh button to refresh the data in the status display. Internet Status > Internet The connection settings for your SX682 WiMAX are displayed in the Internet submenu. Connection status The status of the radio connection with the WiMAX network is displayed as follows: connected = The SX682 WiMAX has established a radio connection with a WiMAX network.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Status.fm / 17.5.11 Local network LAN Schablone 2011_04_07 Local network LAN Status > Local Network The configuration of the local network is displayed in the Local Network submenu. IP address IP address used by the SX682 WiMAX in your local network. Default: 192.168.2.1 Subnet mask Subnet mask of your local network. Default: 255.255.255.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Status.fm / 17.5.11 Device status Schablone 2011_04_07 Device status Status > Device Status The device status of your SX682 WiMAX is displayed in the Device Status submenu. System uptime Operating time of your SX682 WiMAX since it was last restarted. The operating time is given in the format ddd:hh:mm:ss (d=days, h=hours, m=minutes, s=seconds). System time Displays the current date and time.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Status.fm / 17.5.11 Radio status Schablone 2011_04_07 Transmitted power level Current transmission power. Carrier to interference and noise ratio Measurement of the reception quality of the base station. The higher the value, the better the quality of the data transfer to the base station. Centre frequency of current uplink channel Currently used uplink frequency. The reading changes frequently during the measurement.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Using the SX682 WiMAX Schablone 2011_04_07 Using the SX682 WiMAX When you have finished configuring your SX682 WiMAX, use it to surf the Internet, send e-mails or make phone calls via the Internet etc.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Making a phone call or faxing with the SX682 WiMAX Schablone 2011_04_07 Making calls via VoIP Make telephone calls in the same way as on a conventional phone: dial as usual or use the directory to dial. The Phone LED flashes green. Receiving VoIP phone calls Your PC does not need to be switched on for you to receive calls. You only need the SX682 WiMAX to be ready for operation (Phone LED lights up green).
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Schablone 2011_04_07 Making a phone call or faxing with the SX682 WiMAX Consultation Call You are on the phone to subscriber A. During the call you want to call subscriber B with an enquiry. When you finish talking to subscriber B, you want call A to be restored. Key sequence Action You are on the phone to subscriber A. Press the R button. Subscriber A is put on hold. You hear the dialling tone for the second call.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Schablone 2011_04_07 Making a phone call or faxing with the SX682 WiMAX Accepting a call waiting You are on the phone to subscriber A. A call comes in from subscriber B. You want to accept the call from subscriber B and end the call to subscriber A. Key sequence Action You are on the phone to subscriber A. During the call you hear the “call waiting” tone. Hang up the receiver to end the call to subscriber A. Pick up the receiver again.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Schablone 2011_04_07 Making a phone call or faxing with the SX682 WiMAX Call transfer You are on the phone to subscriber A and you want to transfer the call to subscriber B. Key sequence Action You are on the phone to subscriber A. Press the R button. Subscriber A is put on hold. Dial the number for subscriber B. The connection to subscriber B is established. Hang up the receiver. Subscriber A and subscriber B are connected.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Schablone 2011_04_07 Making a phone call or faxing with the SX682 WiMAX Ending a conference call You want to end the call to subscriber B. Key sequence Action Press the R button. The connection to subscriber B is terminated and you continue with your call to subscriber A. You want to end the conference call with both parties. Key sequence Action Hang up the receiver. The conference call is terminated.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Schablone 2011_04_07 Making a phone call or faxing with the SX682 WiMAX Call forwarding You can forward incoming calls to another telephone extension always, on busy or on no response and define each with different destinations. The destinations for forwarding are set via the configuration program, see "Setting up Internet telephony (VoIP)" on page 40.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Operation.fm / 17.5.11 Confirmation tones Schablone 2011_04_07 Action: Deactivating "Forwarding on no response" Press the star key and then the keys 4 and 1. Call forwarding on no response will be deactivated. Action: Deactivating call forwarding in all cases Press the star key and then press twice the key 1. All call forwarding settings will be deactivated.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Appendix Schablone 2011_04_07 Appendix Troubleshooting Fault tracing When troubleshooting, start by checking the LEDs on your SX682 WiMAX. Please answer the questions on the left-hand side and follow the arrows to the answers and solutions: Is the Power LED green? No Power LED not lit up: power supply. Is the mains adapter connected correctly? Is the power socket live? The mains adapter might be faulty.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Troubleshooting Can the configuration program be accessed? Yes Look for a suitable place to set up your SX682 WiMAX; see page 13. Register your SX682 WiMAX with the help of the Basic Setup Wizard; see page 27. No Check the connection to your SX682 WiMAX; see page 62. Is there a connection? Yes The Web browser (Internet Explorer, Mozilla Firefox) is incorrectly configured; see page 63.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Troubleshooting Only a few LEDs have lit up to display the signal strength (RSSI) and the Online LED is green If you are using the antenna integrated in the SX682 WiMAX, turn the SX682 WiMAX until more LEDs light up. Try to place the SX682 WiMAX even closer to the window and check the signal strength bar in the Basic Setup Wizard of the configuration program. Power failure No data will be lost.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Checking the connection to the SX682 WiMAX Schablone 2011_04_07 Checking the connection to the SX682 WiMAX You can check whether the PC is correctly connected to the SX682 WiMAX. This can be done as follows: Open the command prompt on the PC: – Click Start > Run. – Enter cmd in the input field and click OK. The Command prompt window opens. Check whether the SX682 WiMAX responds with the ping command. Enter ping 192.168.2.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Configuring the Web browser Schablone 2011_04_07 Configuring the Web browser If you are using a current Web browser but cannot open the configuration program in it, check the Web browser settings. i We recommend Microsoft Internet Explorer Version 7.0 or Mozilla Firefox 3.0 as the Web browser. Do not use an HTTP proxy for accessing your SX682 WiMAX. Popup windows must be enabled for your SX682 WiMAX.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Configuring the Web browser Schablone 2011_04_07 Allowing pop-up windows Pop-up windows are small windows that are opened either as the result of an action or automatically. The device software for your SX682 WiMAX uses pop-up windows to display the online Help, for example. Many Internet sites, however, call up distracting pop-up windows for effective advertisement placement, for example, without detracting from the layout of the site itself.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Specifications Schablone 2011_04_07 Specifications Model SX682 WiMAX Dimensions Approx. 230 x 160 x 52 mm Operating temperature +5°C to +40°C Network interface 1 Ethernet 10/100BaseT (RJ45) LAN connection (10BaseT Half Duplex,10BaseT Full Duplex, 100BaseT Half Duplex or 100BaseT Full Duplex) Telephone interface 1 FXS (RJ11) for connecting an analogue terminal (telephone, fax machine or answer machine) Frequency 2.3–2.4 / 2.5–2.7 / 3.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Putting into service Schablone 2011_04_07 Putting into service This device is intended for use in the country indicated on the device's label. The device is operated under a single licence, which is held by your service provider. Contact your service provider regarding licensing before you put the device into service. Please observe the legal provisions and local restrictions when putting the device into service.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Open Source Software used in the product Schablone 2011_04_07 Open Source Software used in the product The SX682 WiMAX contains, among other things, Open Source Software, licensed under an Open Source Software License and developed by third parties. These Open Source Software files are protected by copyright.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Open Source Software used in the product Schablone 2011_04_07 Open Source Software Licenses WPA-Supplicant License: BSD WPA Supplicant ============== Copyright (c) 2003-2007, Jouni Malinen and contributors All Rights Reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Open Source Software used in the product OpenSSL License Copyright (c) 1998-2005 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Open Source Software used in the product This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Open Source Software used in the product Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions: 1. The origin of this software must not be misrepresented ; you must not claim that you wrote the original software.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.11 Schablone 2011_04_07 Open Source Software used in the product expat Copyright (c) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper Copyright (c) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Appendix.fm / 17.5.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Glossary Schablone 2011_04_07 Glossary Address Translation (NAT) Network Address Translation. NAT is a method for converting IP addresses (mainly private IP addresses) in a network to one or more public IP addresses on the Internet. With NAT, several network components in a LAN can share a public IP address to connect to the Internet. The network components of the local network are hidden behind the IP address registered on the Internet.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary DNS Domain Name System. DNS permits the assignment of IP addresses to PC or domain names that are easier to remember. A DNS server must administer this information for each local network with an Internet connection. As soon as a page on the Internet is called up, the Web browser obtains the corresponding IP address from the DNS server so that it can establish the connection.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary FTP File Transfer Protocol. Protocol for exchanging files via the Internet. FTP is used, for example, to make files available for download or to receive files from other users. Full duplex Data transmission operating mode in which data can be sent and received at the same time. FXS Foreign Exchange Station. Phone port to which an analogue terminal (phone, fax or answer machine) can be connected.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary IEEE 802.16 Standard defined by the IEEE for WiMAX. Similarly to other standards in the 802 series (e.g. 802.3 Ethernet, 802.11 WLAN), the WiMAX standard is one of the standards for networks. The standard has progressed in accordance with new developments; there are currently two main versions: IEEE 802.16-2004: WiMAX, which specifies the secure location for connection part- ners. IEEE 802.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary IPTV Internet Protocol Television. You receive your provider's television service via the DSL connection. To do this, you require an IPTV-capable set-top box and the configuration data of your IPTV provider. ISP Internet Service Provider. See Provider. LAN Local Area Network, local network. A local network links network components so that they can exchange data and share resources.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary Network protocol The network protocol is the standard via which different PCs exchange data in a network. A connection can only be established between PCs in a network if they all use the same protocol. The TCP/IP network protocol is the most extensive network protocol, which is also used for connections to the Internet. This must be set up on each PC from which a network connection is to be established.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary Server A server makes services available to other network components (clients). The term "server" is often used to refer to a PC. However it can also mean an application that provides a particular service such as DNS, DHCP or a Web service. SIP Session Initiation Protocol. SIP is a standard for data transfer in Internet telephony (VoIP).
SX682 WiMAX / engbt / SX682_FUG_EN_9 / Glossary.fm / 17.5.11 Schablone 2011_04_07 Glossary TCP/IP Transmission Control Protocol/Internet Protocol. Protocol family on which the Internet is based. IP forms the basis of each PC to PC connection. TCP provides applications with a reliable transmission link in the form of a continuous data stream. TCP/IP is the basis on which services such as WWW, Mail and News are built. There are other protocols as well.
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681SIX.fm / 17.5.11 Index Schablone 2011_04_07 Index A Address Translation . . . . . . . . . . . . . Administration. . . . . . . . . . . . . . . . . . system password . . . . . . . . . . . . . . Advanced Settings features. . . . . . . . . . . . . . . . . . . . . Antenna adjusting . . . . . . . . . . . . . . . . . . . . aligning precisely . . . . . . . . . . . . . . integrated . . . . . . . . . . . . . . . . . . . outdoor antenna . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681SIX.fm / 17.5.11 Schablone 2011_04_07 Index Firmware . . . . . . . . . . . . . . . . . . . . . Firmware update. . . . . . . . . . . . . . . . Flat rate . . . . . . . . . . . . . . . . . . . . . . Forwarding always . . . . . . . . . . . . . . . . . . . . . on busy . . . . . . . . . . . . . . . . . . . . . on no response . . . . . . . . . . . . . . . FTP . . . . . . . . . . . . . . . . . . . . . . . . . Full duplex . . . . . . . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681SIX.fm / 17.5.11 Index Schablone 2011_04_07 O Opening online Help . . . . . . . . . . . . . Operating mode Bridge . . . . . . . . . . . . . . . . . . . . . . Router . . . . . . . . . . . . . . . . . . . . . . Outdoor antenna. . . . . . . . . . . . . . . . 25 34 34 15 P Password forgotten . . . . . . . . . . . . . . . . . . . . 60 ping command . . . . . . . . . . . . . . . . . 62 Pop-up blocker Firefox . . . . . . . . . . . . . . . . . . . . .
SX682 WiMAX / engbt / SX682_FUG_EN_9 / SX682_SE681SIX.fm / 17.5.11 Schablone 2011_04_07 Index User interface . . . . . . . . . . . . . . . . . . Basic Setup Wizard . . . . . . . . . . . . menu structure . . . . . . . . . . . . . . . opening online Help . . . . . . . . . . . . setting the language . . . . . . . . . . . 23 27 25 25 24 V Virtual server . . . . . . . . . . . . . . . . . . 82 VoIP . . . . . . . . . . . . . . . . . . . . . . 51, 82 W WAN . . . . . . . . . . . . . . . . . . . . . . . .
Schablone 2011_04_07 SX682 WiMAX / engbt / SX682_FUG_EN_9 / Cover_back.fm / 17.5.11 Issued by Sagemcom Broadband SAS Sagemcom Broadband SAS 250, route de l'Empereur - 92500 RUEIL MALMAISON © Sagemcom Broadband SAS 2011 All rights reserved. Subject to availability. Rights of modification reserved. www.sagemcom.com 05.
