X4 7 5 Barbecue Photograph is not to scale. Specification subject to change without prior notice. Manufactured by Universal Innovations www.saharabbqs.
These instructions are for your safety. Read them thoroughly before use and retain them for future reference. DANGER: If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Parts Supplied Ref Description 1 Cabinet Base 2 Ref Description 1 10 Side Shelf 1 Left + Right Side Wall 1 11 Vaporising Bar 4 3 Cabinet Brace Plate 2 12 Cooking Grill 1 4 Cabinet Front Panel 1 13 Warming Rack 1 14 Grease Tray 1 15 Grease Cup Bracket 1 16 Grease Cup 1 17 Cart Wheel Bracket 2 18 Left Cart Frame 1 19 Cart Wheel 2 5 Cross Bar 6 Axle Assembly 7 Caster Wheel 8 9 Cylinder Supports Firebox Illustration Qty 1 1 2 1 1 3 Illustration Qt
Parts Supplied Ref Description 21 Hardware Supplied Illustration Qty Ref Description Illustration Qty Right Cart Frame 1 A M6x12 Bolt 74 22 Cart Shelf 2 B M4 x 10 Bolt 4 23 Cart Rail 2 C M6 x 45 Bolt 8 24 Handle Assembly 1 25 Side Cart Tabletop 1 26 Utility Bin 1 27 Chopping Board 1 Hardware items are not shown at actual size. Before You Start Check the contents of the box and make sure you have all the parts and fittings listed. If not, call (678) 534 2876.
Assembly Step 1 Cabinet Base Left + Right Side Wall M6x12 Bolt (Ref A) Fit left and right side walls to the cabinet base as shown below using 8 of the M6x12 bolts (Ref A). Note: The right side wall has a hole in the top corner. This is a view from the back.
Assembly Step 2 Cabinet Brace Plate (x2) M6x12 Bolt (Ref A) Fit the two cabinet brace plates to the cabinet base and side wall assembly using 8 of the M6x12 bolts (Ref A) as shown below.
Assembly Step 3 Cabinet Front Panel M6x12 Bolt (Ref A) Note: Flip cabinet assembly over so that the left side wall is on the ground. Fit cabinet front panel to base and side wall assembly as shown below using 6 of the M6x12 bolts (Ref A). Note: An extra person will be needed to hold the door in position while tightening the fixings.
Assembly Step 4 Cross Bar M4 x 10 Bolts (Ref B) Fit the cross bar using 4 of the M4x10 bolts (Ref B). Secure chain to cabinet front panel using the pre-fitted M6x12 bolt and washer.
Assembly Step 5 Axle Assembly Caster Wheel (x2) M6x12 Bolt (Ref A) Turn the barbecue cabinet over and fit axle assembly and two caster wheels to the cabinet base using 16 of the M6x12 bolts (Ref A).
Assembly Step 6 Cylinder Supports M6x12 Bolt (Ref A) Turn the grill over and fit the two cylinder supports to the cabinet base using 6 of the M6x12 bolts (Ref A).
Assembly Step 7 Firebox M6x12 Bolt (Ref A) Position firebox onto cabinet. Open hood and use 4 of the M6x12 bolts (Ref A) to secure firebox into position. Note: Fixing holes are located on inside of firebox (2 on each side). Note: Two people are required to lift firebox into position.
Assembly Step 8 Side Shelf Use pre-fitted R-clip and pin to secure the side shelf. The long bar is used to secure the side shelf in the upright position.
Assembly Step 9 Vaporising Bar (x4) Cooking Grill Warming Rack 1. Fit vaporising bars (x4) into position as shown. 2. Fit cooking grill into position as shown. 3. Fit warming rack into position as shown. 3. 2. 1.
Assembly Step 10 Grease Tray Grease Cup Bracket M6x12 Bolt (Ref A) Grease Cup Attach grease cup bracket to grease tray using one of the M6x12 bolts (Ref A) and then slide into the back of the grill as shown below. Slide grease cup into the grease cup bracket as shown.
Assembly Step 11 Cart Wheel Bracket (x2) Left Cart Frame Cart Wheel (x2) M6x12 Bolt (Ref A) 1. Fit cart wheel brackets to left cart frame as shown below using 8 of the M6x12 bolts (Ref A). 2. Fit the 2 cart wheels to the cart wheel brackets using prefitted bolt and washer attached to wheels.
Assembly Step 12 Right Cart Frame M6x12 Bolt (Ref A) Cart Shelves (x2) Lie the left cart frame down and attach the middle cart shelf first using 2 of the M6x12 bolts (Ref A). Then attach the bottom cart shelf using 3 of the M6x12 bolts (Ref A). Then attach the right cart frame using 5 of the M6x12 bolts (Ref A). Note: There are 3 height options for the shelves. Note: Bolt fixing points are located underneath the cart shelves.
Assembly Step 13 Cart Rail (x2) Handle Assembly M6x45 Bolt (Ref C) Fit two cart rails to cart frame as shown using 8 of the M6x45 bolts (Ref C). Fit handle assembly to side cart using 2 of the M6x12 Bolts (Ref A).
Assembly Step 14 Side Cart Tabletop Utility Bin Chopping Board Attach the side cart tabletop to the cart frame using 5 of the M6x12 Bolts (Ref A). Place utility bin and chopping board into the side cart tabletop as shown.
Assembly Step 15 To fit the cart to the grill body, lift the cart slightly on the left and lower down to lock in to the grill side brackets. Note: make sure the side cart wheels are on the left hand side. If you wish to keep the side cart detached, you can remove the side brackets from the grill.
Assembly Step 16 Load gas cylinder into the cabinet through the back, positioning it between the two cylinder supports and securing with chain. Connect the gas cylinder to the regulator as shown. Perform leak test (see page 22). Use cabinet front panel for easy access to gas hose and regulator. Note: Grease cup needs to be on the opposite side to the gas cylinder. Regulator Gas Cylinder Chain Cylinder Supports Screw regulator onto gas cylinder. 12.25" Use LP gas cylinder, max height 17.
Assembly Step 17 NOTE: Leak Test to be performed before using the appliance. Leak Testing Your grill has been checked at all factory connections for leakage. To be performed in a well ventilated area. Confirm all control knobs are in the off position. To check the connection at the gas hose/regulator/cylinder: 1. Make leak test solution by mixing 50% water with 50% liquid dish soap. 2. Brush several drops of the solution onto the gas hose/regulator/cylinder and hose connection. 3.
SAFETY INSTRUCTIONS Warnings • Failure to read and follow these instructions could result in serious injury or damage to propery. • This product is for OUTDOOR USE ONLY. • This product shall not be used in a building, garage or any other enclosed area. • This outdoor cooking gas appliance is not intended to be installed in or on boats. • This product shall not be installed in or on recreational vehicles.
• Never overload the grill with food – evenly space over the cooking grill surface, ensuring sufficient air circulation to the burners. • DO NOT store or cover the grill until fully cooled. • Keep outdoor cooking appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids. • Do not empty the grease tray until the grill has cooled down. • This product is not suitable for Lava Rock. • Retain instructions for future reference.
Manual Lighting Instructions • Remove the cooking grill and vapor bar from barbecue. • Place a lit match beside the burner (at the same location as the sparker shield) • Push and turn the right most control knob anticlockwise to the high position. • After successful lighting, light each burner from left to right as desired. • If burner fails to ignite after repeated attempts, contact the help line number stated in this manual.
• The burners should be cleaned annually, or whenever heavy build-up is found, to ensure that there are no signs of blockage (debris, insects) in either the burner portholes or the venturi tubes of the burners fitted over the valve outlets. A clogged tube can lead to a fire beneath the grill. Fig. B Vapor Bar • Clean the vapor bar with soap and warm water using a low abrasive cleaning cloth or sponge. CAUTION: SPIDER ALERT! Spiders or small insects can create “flashback” problems.
• Leak test annually and whenever the gas bottle is removed or replaced. Gas and Regulator • The gas hose must be connected in accordance with these instructions. When installe 6. Wire brush entire outer surfaceparts of burner • be If contained the grill is to be stored indoors, thepole gasand gas cylinder c of the to hose should within the Patio Heater remove food residue and dirt. part of hose should be outside bottleofmust be disconnected leftitoutside.
BBQ Specifications Burner 4 Burner Injector Size 0.039" Gas/Pressure 11" per W.C Input Rate (main) 11,700 BTU/HR*1 (Orifice size: 1.0 MM) Standard ANSI STD Z21.58-2018 Outdoor Cooking Gas Appliances TECHNICAL AND SERVICING INFORMATION This appliance is designed for outdoor use only using Propane gas at a supply pressure of 11" per WC and must be serviced by a competent person in accordance with the instructions included. Please read all accompanying documentation carefully.
BARBECUE GUARANTEE This barbecue is made by Universal Innovations. It is made to an exacting quality standard and is covered by the following guarantee. The product has a 10 year limited warranty, regarding proper use.
