Item # IMW385 Owner’s Manual FCC ID:XKK-IMW385
Introduction Thank you for purchasing the Altec Lansing IMW385 Bluetooth Speaker. You can use this speaker to listen to audio wirelessly from devices such as smart phones, computers, iPods, tablets and most other Bluetooth sound sources while you are taking a shower. Please read this manual carefully FIRST in order to get the most out of your speaker. IMPORTANT NOTE: The iMW385 is an IPX5 Splash Resistant certified device.
Features -Seamlessly stream music from your iPad, iPhone, Android device, laptop, tablet or other Bluetooth enabled device. - Bluetooth Specification V4.0 system - Water resistance - Spoken Caller ID Package Contents 1. IMW385 Bluetooth Speaker 2. Micro USB Charging Cable 3. Owner’s Manual with Warranty Information Technical Specifications - Net Weight: 220g - Battery Life: up to 5 hours - AC Adaptor: 5V, 500mA - Power Adapter Input Rating: 100~240V, ~50/60Hz, 0.2A - RF Frequency Range: 2.402-2.480GHZ, 2.
A Quick Look at Your Device 1. Volume Up 2. MF Button 3. Volume Down 4. USB Charging Jack 5.
Charging Your Speaker 1. Connect one end of the included USB Charging Cable to the USB Charging Jack. Then plug the other end of the USB Charging Cable into an available USB port on your computer in order to recharge your speaker’s internal rechargeable battery. NOTE: The internal battery of your speaker takes approximately two to three hours to charge when completely drained. 2. When charging, a red LED light will illuminate. The red light will turn off when your unit is fully charged.
Understanding the LED Status Indicators 1. Bluetooth Connected: Once your speaker is paired to a Bluetooth audio source, a blue LED light flashes once every seven seconds. 2. Incoming Call: A blue LED light flashes twice every two seconds to indicate that you are receiving an incoming call. 3. Low Power Alert: A red LED light will blink and you will hear a beeping noise every minute when your speaker’s battery power is low and needs to be recharged. 4.
Powering Your Speakers ON & OFF 1. To power on your speaker, press and hold the MF button. You will hear an audio confirmation saying “POWERING ON”, and a blue/red LED light will flash alternately after an initial quick blue LED light flashes. 2. To power off your speaker, press and hold the MF button. You will hear an audio confirmation saying “POWERING OFF” Note: Your speaker will power off automatically if left idle for ten minutes.
Setting Up Your IMW385 Bluetooth Music Receiver Bluetooth Device Compatibility Your speaker connects with all Bluetooth devices that support the A2DP profile including iPads, iPhones, iPod touches, and most smart phones, laptops and tablets. Pairing a Bluetooth Device with Your Speaker Press and hold the MF button in order to power on your speaker. You will hear an audio confirmation indicating that your speaker is powered on.
Connecting a Paired Bluetooth Device 1. You should only need to pair your Bluetooth device with your speaker one time. 2. The next time your Bluetooth device and your speaker are in range of each other, and the Bluetooth feature is turned on, they should automatically connect. 3. Your speaker will only automatically connect to the last Bluetooth device it was connected to. 4.
When there is an incoming call: 1. Press the MF BUTTON to pick up the call. 2. Press and hold the MF BUTTON to reject the call. 3. During a call: Press the MF BUTTON again to end the call. 4. If you have a phone paired to your speaker, and the phone is in standby mode or playing music, press and hold the VOLUME UP for 3 seconds to call the last number you dialed. 5. When using your speaker to take a phone call, you can press and hold the MF BUTTON for three seconds to transfer the call back to your phone.
FAQ: Frequently Asked Questions 1. I am having Bluetooth pairing or connection problems, what do I do? A.) Make sure your Bluetooth device is turned on and is on the discoverable mode. (Red and blue LED lights will flash alternately to denote that the speaker is ready to accept connections.) B.) Make sure your speaker is not already connected with another device (easiest way to determine this is if you see a blue LED light flashing once every seven seconds in the center of the speaker). C.
H.) Please note this speaker can be paired with up to 8 devices and will establish automatic connection to these devices. If you’re trying to pair with more than 8 devices, it will pair but you may have issues connecting to the initially paired devices. Please unpair / forget device (for IOS devices) and pair again the device you wish to add and establish connection. 2. My Speaker does not turn ON, what do I do? A) Please make sure you have charged your speakers.
Altec Lansing One Year Warranty Card This warranty covers the original consumer purchaser only and is not transferable. This warranty covers products that fail to function properly UNDER NORMAL USAGE, due to defects in material or workmanship. Your product will be repaired or replaced at no charge for parts or labor for a period of one year.
SHALL APPLY. NOTWITHSTANDING THE FOREGOING, CONSUMER’S RECOVERY AGAINST DISTRIBUTOR SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOLD BY DISTRIBUTOR. THIS WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL CONSUMER WHO PURCHASED THE PRODUCT AND IS NOT TRANSFERABLE. Some countries, states or provinces do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on warranties, so limitation or exclusions may not apply to you.
FCC Statement For Users This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference , and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
