Owner's Manual

ManualsBrandsSalamander Designs ManualsFurnitureCU/WK1

CAPACITIES

(CONTENT)

SINGLE:

l00lbs

TWIN:

00lbs

TRIPLE:

200Ibs

QUAD:

250lbs

CHAMELEON

WALL

MOUNT

TOOLS

REGUIRED

Pencil

Level

COMES

WITH

Drill and Bit:

3/16" (5 mm) for Wood

3/8" (10 mm) for Masonry

Tap

Measure

Bracket

(303-850)

Plastic Wall

Plug

Connector Bolt

(300-540)

Washer

I L 1/8" Hex Key (400-070)

3/16" Hex Key (400-060)

6mm

Hex Key

BEFORE

VDU

BEGIN

• This bracket

intended

for

use with Chameleon

20"

Tall Cabinets.

Stud Finder

Lag Screw Leveling Set Screw

(300-540)

• Total

weight

capacity

each

bracket

is:

100

lbs.

(45kg).

(ex 3 brackets provides

300

lbs.

(135kg).

• Carefully inspect your items

for

shipping

damage

missing parts.

any

damage

apparent

you are

missing parts cont(Jct Salamander Designs Ltd . at

800-535-5659.

• Read

ALL

assembly instructions before assembly.

you have any questions, please contact

your

in~tallation

contractor

Salamander

Designs.

• Use with products heavier than the

maximum

weight

other

than

the cabinet indicated

may

result

in instability causing possible injury

damage.

• Mounts must be attached

specified in assembly instructions.

Improper

installation can result in

serious personal injury.

1. Remove

top

and feet. Install provided connector bolt in previous

foot

locations.

1Gf!

@p'

Summary of content (4 pages)

PAGE 1
- ~ ~ CHAMELEON 0 WALL MOUNT 0 ~ 0~ TOOLS REGUIRED Pencil Drill and Bit: 3/16" (5 mm) for Wood 3/8" (10 mm) for Masonry Tap Measure Stud Finder Level 0 COMES WITH @ Plastic Wall Plug Bracket (303-850) CAPACITIES (CONTENT) SINGLE: l00lbs TWIN: 1 00lbs TRIPLE: 200Ibs QUAD: 250lbs Connector Bolt (300-540) Washer BEFORE VDU BEGIN IIL 1/8" Hex Key (400-070) 3/16" Hex Key (400-060) 6mm Hex Key Lag Screw Leveling Set Screw (300-540) • This bracket is intended for use with Chameleo
PAGE 2
ADJUST FOR LEVEL B. Tighten brackets using a level for proper alignment. Install the leveling screws to bracket without screw protruding through top of the bracket. @ @ CID ·w.· -~r ·w.·· 1 8 1 (fj u. ... -'":. ___ .iJ 9 ,J w u. --- _-_ .... JJ 1 0 Q. (} (fj ~-- ij -~ @ 7. HANG CABINET A. Using two people, lift the cabinet placing the rear upper framing member entirely -into the bracket "hook". FINE TUNE LEVELING A. Adjust side to side to position as desired. B.
PAGE 3
. MARK HEIGHT LOCATION Move the cabinet from the mounting location . Determine the desired height of the top of the cabinet (28" (711 mm) is common). From this height subtract 2-1 /4" (57mm) for a glass top cabinet or 2-7 /8" (73mm) for a wood top cabinet. This will be the location of the top bracket top hole. Using a level, mark the remaining intersecting locations at the same height. Add a second mark 3-3/8" (86mm) below the top bracket hole location for the second fastener for each bracket.
PAGE 4
2. MARK WALL LOCATION A. WOOD CONSTRUCTION - Using a stud finder, mark the locations of the studs in the area to be covered by the cabinet. It may be necessary to shift the cabinet slightly left or right to avoid the mounting brackets being obstructed by the vertical framework of the cabinet. Note: It is not important that the brackets are not located in the same relative location in each bay. As long as a bracket is located every 16" on center sufficient capacity will be met. i Ii I .