Table of Contents 1. Introduction………..…………………..……….... z 2. System Requirements……………………… Preparation……………..………………………. EN 2 3 4 z Component & Accessories…………..…….. 4 z Part Names………………………………….. 5 z Indicator LED………………………………… 6 3. Charging…………………………………………. 7 4. Recording….……………………………………. 9 5. 6. z Car Mode……………..….…………………... 9 z Sport Mode………………………………….. 12 Download………………………………………… z Download from NECKER V1………….…..
1. Introduction Welcome to the world of digital imaging. The following information will help you to use your NECKER V1 to its full capabilities. Before you install and operate the product, please take a few minutes to read through this manual. It provides proper instructions for you to install and operate the product. The NECKER V1 may be affected by static electricity interference. Please plug-in / out and wait a few minutes to start this function.
System Requirements z EN PC System Requirements z Intel® Core2Duo 1.8G or AMD equivalent CPU z Hi-speed USB2.0 port z 1 GB RAM internal memory minimum z 500MB free hard disk space z 800 x 600 pixel color monitor z nVIDIA GeForce MX440 or above, AMD (ATi) Radeon 9200 or above z DirectX 9.0 or higher z Windows® XP (SP2 or higher) / Windows Vista™ / Windows 7™, Windows 8™ Note: If your system is Windows XP Service Pack I, please go to www.microsoft.com.
2. z Preparation Component & Accessories NECKER V1 Sport DV USB Cable Hand Strap QOG User Manual AC Adaptor Camera Holder Waterproof MicroSD Car Charger (optional) Hi-Speed charger cable (For charging use only.
z Part Names EN 5
z Indicator LED Power Record Wireless Battery SD Card Front LED Rear LED Off Off - On Blue, On - Off Off - On Blue, Slow Blink - Off - Off Booting - Red, Slow Blink On - Red, On Blue, Quick Blink - Charge - Green, On Full - Off No Card - Red, Quick Blink Card Full - Red, Quick Blink Low 6
3. 1. Charging EN Remove the rear protective cap of the NECKER V1 and connect the supplied mini USB cable into the NECKER V1. 2. Plug the USB cable into the supplied AC wall adaptor, car adaptor, or a PC / Mac USB port.
3. The NECKER V1 will illuminate the Green LED in the Rear LED to tell you it’s charging. 4. When the Green LED turns off, the battery is full and charging is complete. Note: The Front LED will blink blue and auto power off after 10 seconds when the battery power is low and reference the charging procedure to recharge it.
4. Recording z Car Mode 1. EN Remove the rear protective cap of The NECKER V1 and insert a microSD card (optional) in the microSD Card Slot. 2. Slide the Mode Switch to the Left side. Note: 1. In Car Mode, the NECKER V1 circulate record video and overwrite the oldest recorded file first. 2. The record file automatic divides each 1, 3 or 5 minutes depend on user setting. 3. Hold down the Power Button for 1 seconds and release, the NECKER V1 will illuminate the Blue Front LED and vibrates 3 times.
4. When the wireless module has booted, the Rear LED turn off. 5. The NECKER V1 vibrates 1 time and auto record. The Front LED blink slowly in Blue. 6. To stop recording, hold down the Power Button for 1 second and release, the Front LED stop blink, vibrates 1 time and save the file. 7. Hold down the Power Button for 5 seconds and release. The Front LED turn off and vibrates 3 times then power off.
Note: 1. The Rear LED will blink quickly the RED and the NECKER V1 will vibrate until power off when the micro SD card has full or here is no micro SD card insert into the micro SD card slot. 2. The wireless module will boot at the same time when power on. The rear LED slow blink in red. Reference the “8 Wireless” for more information. 3. NECKER V1 need about 20 seconds to boot the wireless module. The record function will be disable before wireless module has booted. 4.
2. Slide the Mode Switch to the Right side. Note: 1. In Sporty Mode, the NECKER V1 doesn’t circulate record and overwrite the oldest recorded file. It will auto power off when memory card is full. 2. The record file automatic divides each 1, 3 or 5 minutes depend on user setting. 3. Hold down the Power Button for 1 seconds and release, the NECKER V1 will illuminate the Blue Front LED and vibrates 3 times. The Rear LED will blink Red and boot the wireless module.
4. When the wireless module has booted, the Rear LED turn off. 5. Hold down the Power Button for 1 second and release to start video recording. EN The NECKER V1 vibrates 1 time and the Front LED blink slowly in Blue. 6. To stop recording, hold down the Power Button for 1 second and release, the Front LED stop blink, vibrates 1 time and save the file. 7. Hold down the Power Button for 5 seconds and release. The Front LED turn off and vibrates 3 times then power off.
Note: 1. The Rear LED will blink quickly the RED and the NECKER V1 will vibrate until power off when the micro SD card has full or here is no micro SD card insert into the micro SD card slot. 2. The wireless module will boot at the same time when power on. The rear LED slow blink in red. Reference the “8 Wireless” for more information. 3. NECKER V1 need about 20 seconds to boot the wireless module. The record function will be disable before wireless module has booted. 4.
5. z Download EN Download from NECKER V1 1. Remove rear protective cap and power off. 2. Connect the supplied mini USB cable into the micro USB port of the NECKER V1. 3. Plug the USB cable into a PC / Mac USB 2.0 port. 4.
in MSDC mode. 5. You may download your video files from the X:\DCIM\100MEDIA folder. Note: Always eject device from PC / Mac. z Download from microSD Card Reader 1. Remove rear protective cap. 2. Take the microSD card out and insert it to a compatible card reader. your video files from the X:\DCIM\100MEDIA folder.
6. z Playback EN Playback from PC / Mac The video file format is MOV which can be played by QuickTimeTM with PC / Mac. Windows 7: The videos can be viewed by the built-in Windows Media Player or QuickTime. Windows XP: The videos can be viewed by the Windows Media Player Ver. 11 or QuickTime. Mac: Use the built-in QuickTime. Note: For PC version which can be downloaded from: http://www.apple.
7. z 1. Wireless Enable Wireless Function Remove the rear protective cap of The NECKER V1 and insert a microSD card (optional) in the microSD Card Slot. 2. Hold down the Power button for 1 seconds and release, the NECKER V1 will illuminate the BLUE Front LED and vibrates 3 times. The Rear LED will blink Red and boot the wireless module. 3. When the wireless module has booted, the Rear LED turn off. 4. Press and hold the Wireless Button 1 second then release to enable the wireless function.
5. Wait about 2 or more seconds until the wireless function enable. The Red of Rear LED will light 6. Use the mobile device to connect the NECKER V1 and modify settings via the App. 7. To turn off the Wireless function, press and hold the Wireless Button to disable the wireless function. The Red of Rear LED turn off and the NECKER V1 vibrates 2 times.
Android system Please kindly download『Action Cam HD』from Play Store as below: After installed above APP, please connect with wirelessof V1to use. *Please kindly input “1234567890” upon password request. 8. Expert Mode Allow user to adjust the NECKER V1 full function settings by text editor. z 1. Load from NECKER V1 Remove rear protective cap and power off.
2. Connect the supplied mini USB cable into the micro USB port of the NECKER V1. 3. Plug the USB cable into a PC / Mac USB 2.0 port. 4. On a PC / Mac your NECKER V1 will mount to your computer as a mass storage device in MSDC mode. 5. Find “config.txt” from “x:\” folder of micro SD card. Note: Always eject device from PC / Mac.
z Load from micro SD Card Reader 1. Remove rear protective cap and take the micro SDHC out of the NECKER V1. 2. Take the microSD card out and insert it to a compatible card reader. Find “config.txt” from “x:\” folder of micro SD card z 1. Adjust NECKER V1 Settings Open the “config.txt” from text editor as below. (ex. Notepad for Windows.) Model No.
2. Reference the Index Area for detail descriptions then change settings from the Settings Area. 3. Modify the UPDATE: “N” to “Y” before save and close it. Note: It will not active any changed settings if the “N” has not be changed to “Y”. 4. Disconnect the USB cable / insert the memory card to camera then restart and done these settings. Note: The “config.txt” is created by the NECKER V1 automatic when insert a new memory card or even deleted it. All settings are current used by NECKER V1. z 1.
9. FAQ This chapter will list some of the problems you might face when using this device and their solutions. Even if the following guide can not solve your problem, please do not dismantle this device on your own. Please send the device back to the store where you purchased it for maintenance. Q1.Why power indicator is not working? A: Please make sure you are using the car charger from our company. If it is not, it may have connecting problem. Q2.
setup latest version of video codec. Q5.Does it is not smooth enough and have jump seconds? A: NECKER V1 products use standard Micro SD card socket. Please avoid to use Micro SD card which under class 6. Q6.Do I need to reset the date or time after every turning on? A: You don’t need to reset the date or time again. All of information will be remained on this product. Q7.How long does NECKER V1 use? Shall we use power bank? A:NECKER V1 could work for 1.
a problem if out water 3M, please be kind understanding. Q10.How do I use two cable inside NECKER V1 box? A:Hi-speed charge cable if only for charging use not for download video or images. Water proof charge cable could be used for motorcyle when raining.
10. Appendix z Specification Sensor 14M (4608x3288) CMOS 1/2.3” DSP Ambarella A5S Lens 6G+IR, F1.6, f3.6 mm, Optical 160.0° Video Resolution Full HD : 1080P : 1920x1080 @ 30 fps HD:720P : 1920 x 720 @ 30 fps 1920 x 720 @ 60 fps Video File Format MOV White Balance Auto Exposure Auto Video Encoder H.264 Audio Encoder AAC and AC3 mono, sample rate 48K Audio Input Built-in MIC Battery Internal Li-Ion Rechargeable Battery 3.7V / 800mA Storage MicroSD up to 32GB Connector USB 2.
z TC “Config.txt” default Type: Necker V1 Version: Vxx.
CTST (Contrast) : 32 ~ 88 (32)Soft (64)Standard (88)Hard DEF (Digital Effect) : 0 ~ 5 (0)Off (1)Art (2)Sepia (3)Negative (4)Black White (5)Vivid SPLIT (Split File Szie) : 60/180/300 (60)1 Min (180)3 Mins (300)5 Mins STAMP (Date/Time Stamp) : 0 ~ 3 (0)Off(Video stamp will disable in wifi mode) (1)Date (2)Time (3)Date&Time FLK (Flicker) : 0 ~ 2 (0)Auto (1)60Hz (2)50Hz APO (Auto Power Off) : 0 ~ 300 (0)Off (180)3Min. (300)5Min.
TC This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
