Operation Manual


CR626USB

Instruction Manual
Alarm Clock Radio with USB Charging



Please read the instruction carefully
before operating the unit.
EN
1
Location of Control
1. Alarm 1 indicator
2. Alarm 2 indicator
3. USB charging port
4. DC5V jack
5. VOLUME - / ALARM 2 button
6. VOLUME + / ALARM 1 button
7.
POWER ON/OFF / ALARM
OFF / MODE button
8. HOUR / TUNING < button
9. MINUTE / TUNING > button
10. TIME / MEMORY button
11. SNOOZE / SLEEP button
Power Supply
Mains supply : Insert the AC adaptor into a 230V AC ~ 50Hz mains outlet and the other end
of the cord into the DC 5V jack on the back of the unit.
Battery back up : The clock time and alarm (if set) can be maintained during a power
failure by 2 x AAA/ LR03 batteries (not supplied).
Once the power is restored, check the time to make sure it is accurate and re-set if necessary.
Inserting the Batteries
1. Open the battery compartment at the bottom of the unit by pressing on the catch and
removing the cover.
2. Insert 2 x AAA/ LR03 batteries (preferably alkaline batteries) into the battery compartment,
following the polarity as shown on the diagram inside the compartment.
3. Replace the battery compartment cover
Setting the clock and alarm
Setting the Clock
1. Press and hold the TIME button and the hour/minute digits will flash.
2. Use the HOUR button to set the hours. The PM indicator will light when the hour is
advanced into the PM time.
3. Use the MINUTE button to set the minutes.
4. Press the TIME button to confirm.
Setting the alarm
Before setting the alarm time, make sure the Clock has been set.
1. In standby mode, press and hold AL1 / AL2 until “0:00” flashes on the display.
EN
2
2. While “0:00” is flashing, set the alarm time by repeatedly pressing HOUR / MIN.
x Press and hold HOUR / MIN respectively for fast advance.
3. Repeatedly press AL1 / AL2 to select the desired alarm mode (buzzer or radio).
Using the Alarm Function
1. To enable the alarm function, use the ALARM 1/2 buttons to select buzzer or radio. The
selected alarm mode indicator will light up.
2. The buzzer or radio will come on at the set time.
3. To stop the alarm, press the AL OFF button. The alarm will sound again the next day.
Note: While the buzzer alarm volume is fixed and cannot be adjusted, the radio alarm volume can
be adjusted to your desired level using the VOLUME buttons. To select a radio station to wake up
to, see the section on “USING THE RADIO”.
Snooze function
When the alarm sounds, press the SNOOZE button. The alarm mode indicator will flash and the
alarm will sound again
after 9 minutes. To cancel the SNOOZE function and repeat the alarm the next day, press the AL
OFF button.
Sleep Function
With this function, you can listen to the radio for up to 120 minutes, after which it will turn off
automatically.
1. When the unit is switched on, press the SLEEP button repeatedly to select the duration:
120, 90, 60, 45, 30, 15, 05 minutes or OFF.
2. At the end of the set time, the radio turns off automatically.
3. To cancel the sleep function before the end of the set time, press the button to turn
off the radio immediately.
Using the Radio
1. Press the button to turn on the radio.
2. Press and hold one of the <TUNING> buttons to start automatic tuning up/down. Release the
button when the unit is
receiving a station you would like to listen to. For manual fine-tuning, you can press it briefly to
adjust the frequency
step by step.
3. Press the button to turn off the radio.

For optimum reception
Extend and position the FM antenna to achieve optimum reception.
Preset radio stations
You can store up to 20 stations.
Use the <TUNING> buttons to search for a station. Press and hold the MEMORY button to store
the station and a number to be assigned for the preset will be displayed.
