Instructions / Assembly

ManualsBrandsSalsbury Industries ManualsLockers18-51000 Series 1 Compartment Single Tier 18 In. W x 78 In. H x 21 In. D Metal Locker Assembled in Gray

18” Wide Standard Lockers – 18-51000 Series

Single Tier Installation Instructions

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Thank you for selecting Salsbury’s 18” wide standard single tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker

components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on

the outside of the locker or on the exposed surface.

One Wide Locker Assembly

Step 1: Attach the top shelf, bottom shelf, and the first single coat hook to the back

panel.

Step 2: Turn the back panel on its back with the shelves pointing upward. Attach the

first side panel, the left rear leg, and the hat shelf to the assembly from Step 1. Attach

a single coat hook with a double bend to accommodate the coat rod.

Step 3: Attach the second side panel and the right rear leg to the assembly of Step 2.

Attach a double bend for the third single coat hook and install the coat rod as shown

on page 3. The locker chassis is now complete.

Step 4: Attach the pre-assembled door frame onto the assembly of Step 3.

Step 5: Tighten all fasteners checking for squareness of the locker while tightening.

Attach optional sloping hood, end bases or front base (see pages 4 and 5).

Step 6: Place the locker in the installed location and anchor to the floor, wall, or to

both. Individual job conditions will dictate the type of fastening anchors to use (not

provided).

Step 7: Fasten all lockers in a row together by installing fasteners provided through

the side panels. Installation is now complete.

Summary of content (5 pages)

PAGE 1
8” Wide Standard Lockers – 18-51000 Series Single Tier Installation Instructions Thank you for selecting Salsbury’s 18” wide standard single tier lockers. These instructions are intended to assist you in assembling the lockers. Assembly of the various locker components will be with #10 - 24 x 3/8” long slot less screws and #10 nuts (provided). Loosely fasten a screw and a nut into every set of mating holes with the screw heads positioned on the outside of the locker or on the exposed surface.
PAGE 2
18” Wide Standard Lockers – 18-51000 Series Single Tier Installation Instructions Step 3: Attach the second top shelf, the second bottom shelf, and an additional single coat hook to the second back panel as in step 1. Three Wide Locker Assembly Step 1: Attach a top shelf, a bottom shelf, and the first single coat hook to a back panel. Step 4: Simultaneously attach the assembly of Step 3 (second Step 1 assembly), the second side panel, and the second hat shelf to the assembly of Step 2.
PAGE 3
18” Wide Standard Lockers – 18-51000 Series Single Tier Installation Instructions Three Wide Locker Assembly (continued) Step 7: Attach the last side panel and the right rear leg to the assembly of Step 6. On 15” deep lockers attach the last single coat hook. Attach a double bend and install the last coat rod. The locker chassis is now complete. Step 9: Tighten all fasteners checking for squareness of the locker while tightening. Attach optional sloping hoods, end bases or front bases (see pages 4 and 5).
PAGE 4
18” Wide Standard Lockers – 18-51000 Series Single Tier Installation Instructions Sloping Hood Installation (Optional) Step 1: Assemble the top panel to the rear panel with #10 - 24 x 3/8” slot less screws and #10 nuts (provided). Position the flange of the top panel behind the rear panel. Step 3: Attach the sloping hood to the top of the locker with #10 - 24 x 3/8” slot less screws and #10 nuts (provided).
PAGE 5
18” Wide Standard Lockers – 18-51000 Series Single Tier Installation Instructions End Base Installation (Optional) Front Base Installation (Optional) Position the front base between the front legs of the locker with the flange upward. Assemble to the locker with #10 - 24 x 3/8” slot less screws and #10 nuts (provided). Phone: 1-800-562-5377 Fax: 1-800-562-5399 www.lockers.