Installation Guide

ManualsBrandsSalsbury Industries ManualsKitchen19000 Series 30.5 in. W x 20 in. H x 6.25 in. D 8 A / 2 B Doors S-Mounted Keyed Locks Cell Phone Locker in Sand

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-624-5269 Int’l Phone: 323-846-6700

Fax: 1-800-624-5299 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Cell Phone Lockers - 19000 Series

Surface Mounted Installation Instructions

The surface mounted cell phone locker may be installed on the surface of a wall, on a table or a counter top. It is the installer’s responsibility to

ensure the unit is properly anchored to prevent tearing out of a wall or tipping over on a table or counter top.

Installation of the Surface Mounted Enclosure

Remove the locker unit from the enclosure. Drill mounting holes in

the enclosure to fasten it to the mounting surface. It is important to

use at least four (4) fasteners (not provided) and place one each at

the four (4) corners of the mounting surface (either on the rear panel

or the bottom panel). Choose appropriate hardware for the particular

conditions of the installation.

Installing the Cell Phone Locker into the Enclosure

Install the locker unit into the enclosure by sliding it into the enclosure

until its front peripheral flange is flush against the front of the

enclosure. Open the four corner compartments of the cell phone

locker. Install #8 x 1-1/4 in. long screws (provided) through the top

and bottom of the locker unit into the enclosure. Close the

compartment doors.

Summary of content (6 pages)

PAGE 1
Cell Phone Lockers - 19000 Series Surface Mounted Installation Instructions The surface mounted cell phone locker may be installed on the surface of a wall, on a table or a counter top. It is the installer’s responsibility to ensure the unit is properly anchored to prevent tearing out of a wall or tipping over on a table or counter top. Installation of the Surface Mounted Enclosure Installing the Cell Phone Locker into the Enclosure Remove the locker unit from the enclosure.
PAGE 2
Cell Phone Lockers - 19000 Series Recessed Mounted Installation Instructions The recessed mounted cell phone locker must be securely supported by a frame constructed of 2”x4” or 2”x6” lumber. Construct support framing as shown on page 4 of these instructions. Cut a hole in the wall according to the Rough Opening Dimensions calculated on page 3. Installation Instructions Place the unit in the rough opening. Open all left hand compartment doors.
PAGE 3
Cell Phone Lockers - 19000 Series Recessed Mounted Installation Instructions Overall Dimensions and Rough Opening Dimensions Overall Dimensions – 5” Deep Compartments Overall Dimensions – 8” Deep Compartments 7 Doors High 19078-14 19078-21 19078-24 19078-35 6 Doors High 19068-10 19068-18 19068-20 19068-30 5 Doors High 19058-09 19058-10 19058-15 19058-16 19058-20 19058-25 4 Doors High 19048-07 19048-12 19048-14 19048-20 3 Doors High 19038-06 19038-09 19038-10 19038-15 2 “A” Doors Wide 3 “A” Doors Wide 4 “A
PAGE 4
Cell Phone Lockers – 19000 Series Recessed Mounted Installation Instructions Top View of Cell Phone Lockers in Wall Side View of Cell Phone Lockers in Wall SALSBURY INDUSTRIES nd 1010 East 62 Street, Los Angeles, CA 90001-1598 Phone: 1-800-624-5269 Int’l Phone: 323-846-6700 Fax: 1-800-624-5299 Int’l Fax: 323-846-6800 Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted.
PAGE 5
Cell Phone Lockers – 19000 Series Identification Window Installation Instructions Installation of Identification Window 4 Identification labels, clear plastic windows, and metal window backup plates are provided, separately bagged, for use in marking the user’s identity on each locker door. The steps below are numbered according to the picture to the right. 1. Mark the user’s name or other appropriate identity on one of the ½” x 2” labels provided. Tear the label from the card. 3 2.
PAGE 6
Cell Phone Lockers – 19000 Series Resettable Combination Lock Operating & Resetting Instructions The resettable combination lock is a durable and easy-to-use lock providing resettable combination access without the need for keys. Please read this entire page before use. RED/GREEN INDICATOR WINDOW Setup for a Resettable Combination OPERATION KNOB FOUR (4) DIALS 1. If locked, turn the four (4) dials to the factory preset combination (0000) or the known combination that unlocks the lock. 2.