Installation Guide

ManualsBrandsSalsbury Industries ManualsStorage & Organization9000 Series 78 in. H x 24 in. D Standard Storage Cabinet Unassembled in Gray

Storage Cabinets – 9000 Series

Assembly Instructions

Thank you for selecting Salsbury’s storage cabinets. We are confident that the quality and construction of the cabinets will prove to be a good

investment. These instructions are intended to assist you in the assembly of standard, counter height, wardrobe, and combination models.

Individual job conditions will dictate whether the storage cabinets must be anchored to the wall, the floor, or both and the type of fasteners to use to

do so.

General Notes

1. Pages 1 through 6 provide instructions for the 18” deep and 24” deep standard storage cabinets. Pages 7 through 9 provide special information

required to assemble the counter-height, wardrobe, and combination storage cabinets. For other than the standard storage cabinets, use the

standard storage cabinet instructions as a guide while referring to the pictures and special information for the other cabinets. Parts and quantities of

fasteners used will be different than for the standard cabinets.

2. Figure 9 on page 6 shows all the parts for the standard storage cabinet that should be in the package with their names as used in this document.

The parts for the counter height, wardrobe, and combination storage cabinets are shown on pages 7 through 9.

3. All the screwed connections should initially be only finger tight. Square the cabinet assembly before firmly tightening all the screwed connections.

Typical Assembly – Standard Storage Cabinet

1. Lay the Back down on a flat surface with the bottom flange up. The end with no flange and four (4) holes along the edge is the top end. See

Figure 1.

Figure 1

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

www.lockers.com engineering

@lockers.com

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Summary of content (9 pages)

PAGE 1
Storage Cabinets – 9000 Series Assembly Instructions Thank you for selecting Salsbury’s storage cabinets. We are confident that the quality and construction of the cabinets will prove to be a good investment. These instructions are intended to assist you in the assembly of standard, counter height, wardrobe, and combination models. Individual job conditions will dictate whether the storage cabinets must be anchored to the wall, the floor, or both and the type of fasteners to use to do so. General Notes 1.
PAGE 2
. Place one of the Notch Strips along the right side of the Back with the notches inward pointed up and the Notch Strip holes aligned with the holes along the right side of the Back. The Notch Strips are symmetrical end-to-end, so either one fits on either the right or left side of the Back. 3. Place the Right Upright along the right side of the Back with the Back and Notch Strip inside the flanges of the Upright and the top of the Upright at the same end as the top of the Back.
PAGE 3
7. Place Door Frame Assembly upon the Uprights with the top of the Frame fitting over the Top panel. Fasten Door Frame Assembly to the Uprights using seven (7) screws and nuts on each side hidden inside the flanges. Fasten the front edge of the Top panel to the top of the Door Frame Assembly using four (4) screws and nuts. See Figure 4.
PAGE 4
8. Fasten Right Door with holes for Handle and lock to hinges on right side of Frame. Attach using two (2) screws and nuts per each of the three (3) hinges. Repeat to fasten Left Door to hinges on left side of Frame. For this step it may be more convenient to stand the cabinet assembly up vertically. However, the illustrations show the cabinet remaining in the beginning position. See Figure 5. Figure 5 9. Mount Handle on Right Door with two (2) screws and lockwashers.
PAGE 5
10. Rotate latch to position shown below. Mount Lock Bars on Latch as shown below. Do not fasten Latch to Handle yet. Rotate Handle to open (unlatched position or horizontal) position. Insert Lock Bars into plastic Guides while aligning square hole in Latch with square threaded shoulder on Handle. Install lock nut on threaded shank of Handle. Check that Handle, Latch, and Lock Bars operate smoothly and effectively. See Figure 7. Figure 7 11. Open the Doors.
PAGE 6
Figure 9 - Standard Storage Cabinet – Parts Identification and Count SALSBURY INDUSTRIES 1010 East 62nd Street, Los Angeles, CA 90001-1598 Phone: 1-800-562-5377 Int’l Phone: 323-846-6700 Fax: 1-800-562-5399 Int’l Fax: 323-846-6800 Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability. Copyright © 2010 Salsbury Industries. All rights reserved. (Rev.
PAGE 7
Assembly Special Information – Counter Height Cabinet The parts for the counter height storage cabinet are much shorter in vertical height than the standard storage cabinet. The only parts that are the same as in the standard cabinet are the handle, latch, lock bar guides, shelf, and bottom. The Top sits on top of the flanges of the Back and the Right and Left Uprights and the seven (7) screws and nuts to attach the top are hidden inside the flanges of the Top.
PAGE 8
Assembly Special Information – Wardrobe Cabinet 1. Assemble the Back, Notch Strips, Right and Left Uprights, Top, and Bottom in that same manner as in the standard cabinet. 2. Assemble the two (2) Rod Hangers to the outside of the centers of the side flanges of the Top Shelf. Each Rod Hanger is fastened with two (2) screws and nuts. Install the Coat Rod into the hangers before fastening the second hanger. See illustration below. 3.
PAGE 9
Assembly Special Instructions – Combination Cabinet 1. Assemble the Back, Notch Strips, Right and Left Uprights, Top, and Bottom in that same manner as in the standard cabinet. 2. Assemble the two (2) Rod Hangers to the outside of the centers of the side flanges of the Top Shelf. Each Rod Hanger is fastened with two (2) screws and nuts. Install the Coat Rod into the hangers before fastening the second hanger. See illustration below. 3.