Installation Guide

ManualsBrandsSalsbury Industries ManualsKitchen92000 Series 38.25 in. W x 74 in. H x 18 in. D 2-Tier Plastic Lockers Unassembled in Blue

Plastic Lockers – 92000 Series

Models 92168 & 92368 Double Tier

Assembly Instructions

Thank you for selecting Salsbury 92000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a

good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the

lockers must be anchored to the wall, the floor, or both. Please read the entire assembly instruction document before beginning assembly.

Step 1. Insert the back panel tabs into the pockets along the rear

edge of the side panel. Tap with soft mallet to engage two (2) latch

points.

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Step 2. Press another side panel onto the tabs on the other side of

the back panel. Tap to engage as above.

Step 3. Join and press down the sides-and-back-panel assembly

from step 2 above into the base panel as shown below. The base

panel is the thicker of the three (3) horizontal panels provided. Then

thread four (4) leveling feet provided into the bottom of the base

panel.

Step 4. Join two long interlocking plastic joint pieces and one short

interlocking plastic joint piece into a U-shaped assembly as shown

below. Press the U-shape assembly down onto the U-shaped top

edges of the lower (first) unit assembly from step 3.

LOWER

(FIRST)

UNI

Step 5. Assemble a second unit per Steps 1 and 2. Press this

assembly into the joint assembly on the top of the lower half of the

unit from Step 4 above. Then press down one of the two top panels

(thinner) onto the top of the assembly.

SIDE

PANEL

BACK

PANEL

OTHER

SIDE

PANEL

BASE PANEL

(

THICKER

)

SHORT

STRIP

LONG

STRIPS

TOP PANEL

(THINNER)

INTERLOCK

INTERLOCKING

JOINT

ASSEMBLY

LOWER HALF

OF THE UNIT

LOWER

(FIRST)

UNI

LEVELING FEET

(NOT SHOWN)

JOINT

SSEMBLY

LOWER

(FIRST)

UNI

JOINT

ASSEMBLY

Summary of content (4 pages)

PAGE 1
Plastic Lockers – 92000 Series Models 92168 & 92368 Double Tier Assembly Instructions Thank you for selecting Salsbury 92000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the lockers must be anchored to the wall, the floor, or both.
PAGE 2
Plastic Lockers – 92000 Series Models 92168 & 92368 Double Tier Assembly Instructions Step 6. If no optional sloping hood is ordered, install the three filler strips into the recesses in the top of the remaining (second) top panel. FILLER FILLER STRIPS STRIPS INSTALLED Step 7. Assemble a second compartment per steps 1 though 5 except without a base panel and using the second top panel with the filler strips installed. This unit will not have leveling feet.
PAGE 3
Plastic Lockers – 92000 Series Models 92168 & 92368 Double Tier Assembly Instructions Step 11. Fasten the eight (8) hinges (four (4) for each of the two (2) doors) provided in the hardware package securely to each hinge position with the screws provided as shown below. Fasten each of the two (2) doors to the appropriate set of hinges. Step 12. Install coat rods by pressing ends into locating tabs near top of compartment. Use the locating tabs behind the stiffener rib. HINGES COAT ROD Step 13.
PAGE 4
Plastic Lockers – 92000 Series Models 92168 & 92368 Double Tier Assembly Instructions Step 15. Install placards (optional) in the indentation near the top of each door. Step 16. If two (2) or more lockers are to be installed side by side, the lockers should be fastened together with the four (4) nuts and long screws provided. Select two (2) available holes toward the front and any two (2) holes toward the rear. The illustration below shows the 12 holes that are available.