Installation Guide

ManualsBrandsSalsbury Industries ManualsKitchen93000 Series 38.25 in. W x 74 in. H x 18 in. D 3-Tier Plastic Lockers Assembled in Tan

Plastic Lockers – 93000 Series

Models 93168 & 93368 Triple Tier

Assembly Instructions

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Thank you for selecting Salsbury 93000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a

good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the

lockers must be anchored to the wall, the floor, or both. Please read the entire assembly instruction document before beginning assembly.

Step 1. Insert the back panel tabs into the pockets along the rear

edge of the side panel. Tap with soft mallet to engage two (2) latch

points.

Step 2. Press another side panel onto the tabs on the other side of

the back panel. Tap to engage as above.

Step 3. Join and press down the sides-and-back-panel assembly

from step 2 above into the base panel as shown below. The base

panel is the thicker of the four (4) horizontal panels provided. Then

thread four (4) leveling feet provided into the bottom of the base

panel.

Step 4. Install a thinner top horizontal panel on top of the unit.

Step 5. Assemble two (2) identical units the same as Steps 1

through 4, except installing the thinner top panel on each instead of

the thicker base panel. These units will not have leveling feet.

Step 6. If no optional sloping hood is ordered, install the three (3)

filler strips into the recesses in the top panel of the upper unit.

SIDE

PANEL

BACK

PANEL

OTHER

SIDE PANEL

BASE PANEL

(THICKER)

SIDE

PANELS

TOP

PANEL

BACK

PANEL

LOWER

(FIRST)

UNIT

UPPER

and 3

rd)

UNITS

LEVELING FEET

(NOT SHOWN)

TOP PANEL

(THINNER)

LOWER

(FIRST)

UNI

FILLER

STRIPS

FILLER STRIPS

INSTALLED

Summary of content (3 pages)

PAGE 1
Plastic Lockers – 93000 Series Models 93168 & 93368 Triple Tier Assembly Instructions Thank you for selecting Salsbury 93000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the lockers must be anchored to the wall, the floor, or both.
PAGE 2
Plastic Lockers – 93000 Series Models 93168 & 93368 Triple Tier Assembly Instructions Step 7. Stack the two (2) upper units onto the lower unit. Press all units firmly together. Use a mallet if necessary. PANEL WITH FILLER STRIPS (IF NO OPTIONAL SLOPING HOOD) Step 9. Attach the plastic oval lock plate to the front of the three (3) doors with two (2) screws from the rear of the door. Insert the stainless steel hasp through hole in front of doors making sure cutout is facing downward.
PAGE 3
Plastic Lockers – 93000 Series Models 93168 & 93368 Triple Tier Assembly Instructions Step 11. Slide the shelves (optional) into the slots in the locker side panels. There are three (3) slots available for shelves in each of the compartments. SHELF Step 14. If two (2) or more lockers are to be installed side by side, the lockers should be fastened together with the four (4) nuts and long screws provided. Select any two (2) holes toward the front and any two (2) holes toward the rear.